Mazda 3 LED Interior How To Install - 2003-2009

[@arc2rus]

Thanks a huge bunch, my car's speedo was flashing when I turned off the engine and I realized it was the glove lights blowing out and that was the 'symptom'. Had no spare bulbs and was worried the car would run out of battery overnight and used this amazing tutorial to temporarily swap out a bulb from the interior lights

[@matthewbrowne9955]

This helped me so much! I bought some LED's on Amazon, I wrote a product review and posted a link to this video with it. Very helpful, hopefully it will help other people too!

[@PrecisionLED]

We are glad to be of assistance!

[@Kasz2001]

Thanks heaps from Singapore - the most expensive place to buy a car in the world!

[@andreicuy8721]

Omg, thanks a lot, this helped me so much, thanks again!

[@jsonzbl21]

awesome tutorial! installed mine smoothly. thanks!

[@PrecisionLED]

Glad to hear!

[@spacecalander]

Just installed my interior kit from you. Very awesome thanks.

[@PrecisionLED]

Thanks for the support!

[@JasminMarsters]

What if you meed to replace the whole thing? I bought the replacement but feel a bit intimidated by all the wires 😅

[@aaronbridgeforth4942]

How do you remove the rear dome housingm My switch does not properly. Have to apply upward pressure for the bulb to turn on. Thanks

[@domnicfernandes4987]

Nice video thanks guys keep up the good work.

[@PrecisionLED]

We are glad to be of assistance!

[@sf945]

What is the size of the bulb 1:47-2:30? This was very helpful video, I managed to change all bulbs, thanks (but not that one I'm asking, can't say if it's 30mm or 31mm -does it really matter??)... I changed glove box light also.

[@PrecisionLED]

This would indeed be a 31mm LED fitment. It is likely a 29mm and 30mm would fit as well. You can find the bulb fitment here: www.precisionled.com/premium-festoon-31mm-canbus-3smd-5730-led.html

[@sf945]

PrecisionLED Thank you. Bought 30mm and it fits & works well. And thanks again for this video, very helpful!

[@rachelbbq]

Does the SMD matter for the festoon bulbs? Do you have to have a 4 SMD LED or can you use 6, 2, etc. as long as they are 31mm?

[@arturocivit]

Hi thanks for this, but how you get off the trunk bulb?

[@PrecisionLED]

The trunk LED installation should be the exact same as the other lights shown in the video. All of the lights are very simple to access with our trim tool set, which comes complimentary with any LED package purchase.

[@kev5525]

can i install any type of LED Lights as long as it fits? because i have a 2008 Ford Escape XLS (no sun/moon roof) i need 4 leds for interior and 2 for my license plate.

[@PrecisionLED]

If it fits it should work. Although we would recommend purchasing a set of LEDs specifically designed for your vehicle.

[@PokemSockemHockey]

i have a 2011 , whould it be good this way too ? and are the bulbs different ?

[@PrecisionLED]

juliano3101 The install is similar but some of the LEDs are different.

[@3rdWorldPrepper]

thanks for a great and simple vid Bro!

[@PrecisionLED]

We are glad to be of assistance!

[@Blabla1enjoy]

Nice tutorial very helpfull

[@PrecisionLED]

Glad we could hep!

[@Samsancas]

Thank you very much!!!

[@PrecisionLED]

You are very welcome!

[@cesarabanto387]

Great!!!!. Thanks.

[@PrecisionLED]

Thanks for tuning in!

[@ivanespinoza4108]

did you found any tutorial? i own a 2012 , glove box bulb is the only one i couldn't change.

[@PrecisionLED]

We will try to do a glove box tutorial in the future! However, the glove box installation should be very similar to the lights in the video. You would just use one of our tools to pry the casing open.

[@PrecisionLED]

Hi, This Mazda 3 does not have a glove box bulb replacement available which is why we didn't show it in the tutorial. Thank you.

[@TheEpistemologo]

PrecisionLED hi, thanks for the video. It was useful The glove box uses a t10 the same as the front map lights.

[@tosgaly]

They do have a glove box light and they turn to be troublesome if more than 2 bulbs are burnt. For instance, when my bulb was burnt my whole dash remained lighted on and had to turn the fog lights on as a workaround. My battery wasn't happy about it

[@mourinho9607]

I am so mad that i am late to this video. I removed the entire rear dome panel to change the LED light and now the whole thing doesn't fit in properly anymore. Am not sure if I have broken anything. Nothing falls down. Any idea?

[@PrecisionLED]

If you would like, feel free to send a picture to [e-mail] and we can try to help you out!

[@cobiej09]

What bulb sizes are they

[@PrecisionLED]

There are a variety of sizes, could you specify which bulbs you are interested in?

[@eric1086]

Hey, Looks like a great kit. I have to ask, how does this affect the fade on/off?

[@davidkearney3359]

I bought an LED kit and the fade on/off is still fully functional. I was also concerned about it and was pleasantly surprised it worked out.

[@PrecisionLED]

Thank you for the interest. There will be no difference with the fade in/out effect. It will still work exactly like your halogens!

[@tamez1988]

THANK YOU!!!👍🏼👍🏼👍🏼👍🏼👍🏼😀

[@PrecisionLED]

You are very welcome! 🙂

[@dadamichiko20]

will this be similar installation with a 2012 Mazda 3?

[@PrecisionLED]

We have a video for the 2nd gen Mazda 3 installation: kzbin.info/www/bejne/nWGwhWuVq76Jeq8

[@spacecalander]

What color was this kit, i like it

[@PrecisionLED]

In this video we used the 6000k.

[@tksqqo]

How to change a clove box light??

[@PrecisionLED]

The glove box installation should be very similar to the lights in the video. You would just use one of our tools to pry the casing open.

[@Naitsirhc0777]

Who is the model Led of Read dome in mazda 3?

[@PrecisionLED]

The LED we used is a 31mm festoon, which you can find here: www.precisionled.com/premium-festoon-31mm-canbus-3smd-5730-led.html

[@stormvayu]

thanks you

[@PrecisionLED]

You are welcome!

[@cobecerram]

Nice tutorial, but what about the glove box?

[@PrecisionLED]

The glove box installation should be very similar to the lights in the video. You would just use one of our tools to pry the casing open.

[@cobecerram]

I didn't find anything about the glove box bulb replacing, and mine had burn it :(

[@PrecisionLED]

The glove box installation should be very similar to the lights in the video. You would just use one of our tools to pry the casing open.

[@PrecisionLED]

6000K

[@silvanarias5595]

your shipment prices are way too much :(