Respect to him for doing all this custom work himself instead of just paying a shop to do it all for him
@WZ_TV3 жыл бұрын
Thank you sir!
@VirginiaPatriotRebel3 жыл бұрын
Mad respect bro, you're a true speed master. I had a ton of questions about this trans and you just answered them all... Bravo 👏🤘
@WZ_TV3 жыл бұрын
Thank you sir. Thats what im hoping for, that these videos become useful to someone 🔥🔥🔥
@raquielcross57573 жыл бұрын
Always enjoy watching your progress in this super project 👍😁 and skill...
@WZ_TV3 жыл бұрын
Thanks man. I see your comments in all my videos. Apprecaite you!
@raquielcross57573 жыл бұрын
It's a pleasure ☺
@matthewnivens73513 жыл бұрын
I need to do this with mine. My transmission took itself out of 6th and locked in forth. Now I have a reason to do this. Thanks for the info man
@WZ_TV3 жыл бұрын
Awesome! 👊🏻👊🏻
@davidseupakisi14 жыл бұрын
Awesome, your work is on point 👌 looking forward to seeing it completed
@WZ_TV4 жыл бұрын
David Seupakisi thank you sir! Apprecite it
@buckrogers88583 жыл бұрын
Mad respect for this guy. I love the content. Ha I might start working/modding my 14 year old Speed 3
@WZ_TV3 жыл бұрын
Thank you sir 🙌🏻🙌🏻
@bigboostmcgee42114 жыл бұрын
Awesome progression.... keep it up 🤙
@WZ_TV4 жыл бұрын
Thanks ✌️
@akaitv66062 жыл бұрын
Excellent work mate
@davidg111344 жыл бұрын
Nice job ! love that ecu relocate! lol
@edgarcoward11663 жыл бұрын
Plan on doing this since I'm grinding when I shift from 1st, 2nd and 3rd... But I'm going to be wearing gloves...
@ChrisVega-eq8gf2 ай бұрын
Eres un caballo Arielito!
@michaelregalia253922 күн бұрын
Are the first and 2nd gear shift forks the ones with the pins?
@MrPatc074 жыл бұрын
Sick!! Nice job
@AhmedBahgat2 жыл бұрын
Hello mate. Great job. may I ask you a question please. After you finished everything including painting then closing the two halves of the gearbox, was it easy to put the transaxle cover back on, bearing in mind you have limited time to intsall the cover because of the RTV, my concerrn is how all these bearings and rods align exactly in theor resting spots while you are colsing the two halves? Your input and expereince will be greatly appreciated. Cheers
@WZ_TV2 жыл бұрын
It just falls in place with no issues. You will have to press open the C clips on top so the shaft sits all the way. I would say thats the last 1/4” before is fully seated.
@akaitv66062 жыл бұрын
Hi mate , I've got a lot of play on my gearbox , where the LH cv shaft goes into the gearbox/diff , what part is likely to be causing all the sloppiness ??. Is there some tind of bearing in the diff that would cause 2mm of travel??.
@WZ_TV2 жыл бұрын
Yes the diff has a bearing on both side. Maybe one is worn out and is letting it move.
@zakura70jr Жыл бұрын
Which gear stacks hold which gears?
@AhmedBahgat2 жыл бұрын
Good job mate, I want to do my nazdaspeed3 gearbox but really scared, maybe your video will help me but may I ask you please, I have a little whining on 6 gear at about 100 km/h but only if I let go of the gas pedal, if I press the gas pedal even slightly the whining disappears, what bearing inside the gearbox you reckon is causing that? Cheers
@WZ_TV2 жыл бұрын
Thank man. This transmissions dont have many bearings. Just 1 on each end of the stack. Is hard to say exactly whats wrong with yours. Specially since im not a transmission expert by any means. You would have to take it apart to see where the damage is.
@AhmedBahgat2 жыл бұрын
@@WZ_TV Thanks for the reply mate, started the project two weeks ago and just managed to get the gearbox opened today, so heavy man, I am doing the job with weak health and jwith just the help of my 18 years son who has absolutely no experience, I am teaching him, I am taking my time doing the project as I have no time limit, I am changing all 3 shafts rear and front berarings, as well the input shaft oil seal and the whole diff with Quaife LSD ATB diffrential, new diff bearings and oil seals as well. but I am worried about the ring gear on the diff as I have to remove it from the old diff and install it on the new diff, are those 16 bols holding it tight? and what size in mm as I have not removed the shafts and diff yet to find out, just opned it and horrifically scared, how you managed to tight those 16 bolts to about 100 NM while the diff is loose, should I use a press to hold the diff? Should I use blue lock tight with those 16 bolts? Thanks a alot and sorry for the hassle. Cheers
@WZ_TV2 жыл бұрын
@@AhmedBahgat i took the bolts off with an impact gun. You will need a press to get the ring gear off. And to put the new one on as well.
@jmeza1572 жыл бұрын
Hey brother! What adhesives did you use for the pads? Also what sealant did you use to seal up the trans again?
@WZ_TV2 жыл бұрын
Pads are pressed in. For the case gasket maker.
@AhmedBahgat2 жыл бұрын
Hello mate. Great work, thanks for all your videos. I have a question please, my Mazda 3 MPS whines a lot on 6th gear when you release the gas pedal at 100 km/h, that whining disappears when you accelerate but if you release the gas pedal the whining comes again. I am thinking it is a bearing, but which bearing? Cheers
@WZ_TV2 жыл бұрын
Hey thanks. Im no expert on transmissions to be honest but you are right whinning noise is usually a bearing. I would say since the gear itself doesnt have a bearing it should be the closest to gear 6. But it can also be the way 6th gear engages with the main shaft. Like when diffs make whining noises its the engangement between the gears that is worn out and makes the noise. You would have to open it to get a better look at whats going on.
@akaitv66062 жыл бұрын
Mate where do you get preload shims for the diff from and spider gears , are there any good parts available??
@WZ_TV2 жыл бұрын
Any part you need for the tranny needs to go through mazda dealer. Havent found any online store with parts.
@luistroll224 жыл бұрын
Almost ready for that first start! Y salud pana mio
@WZ_TV4 жыл бұрын
Jose msp3 almost there! Saludos!
@meowschwitz29923 жыл бұрын
Where did you get the longer gears. I’m looking for some longer gears for the gen 2. Like euro gears.
@WZ_TV3 жыл бұрын
Speed performance. I think they discontinue them
@dairagitcrew25213 жыл бұрын
VeryGood build 🥰, just discovered youre channel , nice to see more people reping the speeds 🤜 how much did the gearbox re furb cost in total please?
@WZ_TV3 жыл бұрын
Thanks man! How did you find my channel? The final drive was about $1200 and the fork pads was around $300.
@dairagitcrew25213 жыл бұрын
@@WZ_TV literally the orange caught my eye 👁 on my KZbin feed noticed it was about mazdaspeeds and here I am 😂 thanks for the info, im hoping to get the final drive done in my 6 after I get a real turbo lol another thing I wanted to ask is do ss supply both?
@WZ_TV3 жыл бұрын
@@dairagitcrew2521 hahaha ok thats cool. No they only had the pads. The final drive i got it from speed performance.
@dairagitcrew25213 жыл бұрын
@@WZ_TV thanks again, hope to see some pulls soon 👌
@WZ_TV3 жыл бұрын
@@dairagitcrew2521 thank you sir 🙌🏻
@cyraxkkcb2mo104 жыл бұрын
4rd power zoom zoom Mazda
@kwbalance1083 жыл бұрын
11:43 Hol up, though. How did you get the pins out? Picks? Magnet?
@WZ_TV3 жыл бұрын
For the pins i used an Air Hammer.
@kwbalance1083 жыл бұрын
@@WZ_TV Good to know, thanks man!
@WZ_TV3 жыл бұрын
@@kwbalance108 no problem!
@jmeza1572 жыл бұрын
great contact bro! can you help me identify 1&2, 3&4, 5&6 shift forks?
@WZ_TV2 жыл бұрын
Thanks man. 1st and 2nd are the biggest gears. That should let you know.
@jmeza1572 жыл бұрын
Thanks man and las question what adhesive did you use to apply the pads and did you use any thing to seal up the transmission?
@zacharygardner20873 жыл бұрын
How did you get the snap rings off of the shafts and how did you get them to drop down so you could separate the gear Box from the bell housing
@WZ_TV3 жыл бұрын
I think i explain that in the video. The gear box has 2 C clips holding the gear stacks. Just have to expand them and they will drop from the case.
@dread3453 жыл бұрын
@@WZ_TV tips on getting the shifter back in i cant get shifter and the tabs to line up perfectly in the middle to install shifter once bellhousing is back together
@WZ_TV3 жыл бұрын
@@dread345 i use a long screw driver to get all the forks aligned inside. The wiggle the shifter in. It’ll fight you for a bit. The problem is more at the end. There is a bearing hole that the shaft needs to sit on. Just keep at it
@dread3453 жыл бұрын
@@WZ_TV yeah bearing hole is where im stuck at now, cant seem to get the shifter tabs aligned and into the bearing hole, why does this have to be made so complex lol
@dread3453 жыл бұрын
any tips as far as the back tabs? how will you know if you messed up the synchros, will everything not align?
@williamalarie49744 жыл бұрын
Is that still the speed 3 beacause the last Time i watch you is 5 year agi
@WZ_TV4 жыл бұрын
William Alarie yes sir same speed. Welcome back!
@guy2423 жыл бұрын
Looking good. Where did you get the brass pads?
@WZ_TV3 жыл бұрын
Thank you! Speed Solutions sell them
@guy2423 жыл бұрын
@@WZ_TV awesome. Thank you.
@WZ_TV3 жыл бұрын
@@guy242 no problem
@ariancasas15044 жыл бұрын
👌👌👌👌sweet 👍👍👍👍
@tylerwoods94453 жыл бұрын
Where did you buy the packs at?
@WZ_TV3 жыл бұрын
Speed performance
@lesthercurbelo44164 жыл бұрын
nice shirt bro. .😂😂😂
@dantheman19982 жыл бұрын
how much HP can these trannys handle?
@WZ_TV2 жыл бұрын
I ran it for 3 years with 800hp no issues.
@speedy_polak47112 жыл бұрын
What RTV did you use when mating the case halfs together?