Meteor65 HD Review + NEW BETAFPV 1S AIO FC with BUILT-IN VTX

[@Holyfield]

Hey Mr. ShutterBug, just wanted to tell you, I did what you recommended and swapped the Meteor65HD frame into a Meteor75 frame with 40mm props since I wasnt happy with the default setup at all. You were right, everything is sooo much improved now. Better flight characterstics, 30% longer flight time (on stock 1s 300mha), quiter. Its a much more stable platform for the HD recordings now. You gained a subscriber!!

[@fpvcruzer]

This is awesome. I have an extra meteor 75 frame and would love to put the meteor 65 parts onto that frame. What are your flight times like?

[@Holyfield]

@@fpvcruzer hey there, flight time is around 4mins (light crusing) on betafpvs 450mAh 1s lipo down to 3.3 volt, cant recommend the 300mAhs on it..

[@fpvcruzer]

@@Holyfield thanks so much for the information! I already have the 450s and would love to have the hd video footage. Your flight times sound good! I am going to order this drone and convert it.

[@fpvcruzer]

@@Holyfield So I bought the Meteor 65 hd and converted it just like you did and am very happy with it. Definitely an improvement and a lot of fun to fly. Love the HD footage and the sound isn't so bad in slow motion.... If I had to do anything else it would be to get a better rx because the spi receiver doesn't get as much range as I would like.

[@fpvcruzer]

@@sebasgovel there is no soldering required for this modification. You are basically disassembling the meteor 65 and The motors unplug. I used the meteor 75 frame because it has the same holes for all the screws used to attach the motors, flight controller and canopy. Go for it!

[@JuanCintron]

Thank you for this review! We will love to see a video of the upgrade results! Agree that the 75mm frame will be much better. Done that with my mob6 HD. Love to see the results on this 65mm convertion. Perhaps motivate me to order one too.

[@3DMOFO2020]

3:02 well that's the deal breaker for me Nate Great job on the video and the flight

[@AaronSchwarz42]

Too bad it has so much latency. I suspect the daughter board for HD video might be causal //

[@AaronSchwarz42]

Helpful heads up // Hello Nate, when your showing "Smoke" near your front yard, the street address across the street on the curb & street sign gives away cross street // I am telling you because that could make it easy for a bad actor to find a high precision location by extracting visual data from FHD version of this stream (I sincerely hope not) & you might edit to remove this kind of content FYI // especially if your channel becomes really well known or very popular - there are some seriously crazy weirdos near Seattle / though that part near MSFT a very low crime area // Cheers buddy & happy FPV action / I am just dipping my toes into the hobby // thanks for the quality content!

[@peterowland1552]

As ever great stuff, thank you! Really enjoy your further development ideas, brilliant. Stuck with tuning Tinyhawks but will one day switch, might just let the tech improve a tad more..

[@AaronSchwarz42]

Exciting to see how fast these little FPV drones improving // I got a DJI Mavic Mini 2 for CINE 4K stuff & its also amazing how fast that lineup has improved //

[@kaasovic]

Really nice! I agree - flew the meteor 75 with 1102 18,000kv and think this would probably perform better on that setup. A little quieter too it seems. Nice review, I’d like to try the board sometime

[@GKW25308]

Looking forward to seeing all that gear on the larger frame with 40mm props and bigger battery. Interested to see what flight times you can get and how much quieter it is.

[@zwaaaaaa]

+1

[@25JoaoRafael]

your wall decor is really cool

[@duncanwilliams5790]

Nice one. Hoping the FC has pads for an external RX as I prefer the reduced latency of crossfire for indoors. I have the NBD BBBL with crossfire & a goober canopy and LOVE IT. Excited to check out the motors, replacing my old & tired 0802 19500kv on this, my main whoop & see how they perform with a dry weight of ~ 21g.

[@MrShutterBug]

Unfortunately I don’t see any way to add an external receiver. SPI receivers may not be as fast as CRSF, but they are pretty fast. Faster than SBUS receivers. I run D8 which has 9ms of latency. Not bad.

[@duncanwilliams5790]

​@@MrShutterBug So no sign of spare UARTs broken-out on the board itself? Slightly disappointed at that, but will wait for the board to be released and their full tech specs before I lose hope. Fast is good, pretty fast isn't - when I have the choice, even if it costs me a few grams. Mine's 23.95g with BBBL & goober, along with crsf & minimortal-t which is pretty heavy, I'll admit, but it goes like stink! Must be 600+ batts through it as-is, so the new motors and maybe new FC is desirable ... just don't want to give up the stick feel of the Tango2 and the 150Hz CRSF responsiveness. I notice a pretty big diff between that & my FrSky/Taranis X9D. Tempted by the IRC Ghost for further-reduced latency and ultralight RXs, but will have to put a few more kays on the CRSF setup first.

[@marksherman630]

Very interested in your "how to improve it" comments in all your videos. Really helps in understanding how build options affect performance. Would moving from a 65mm to a 75mm frame improve the same way generally (1s or 2s with or without an HD camera)?

[@MrShutterBug]

Yes. If you take drone like the regular (non-HD) Meteor65 or Mobula6 and convert it to use 40mm props, it will have more power and get longer flight time. There is a real advantage to having those larger props. BUT I still love 65mm whoops, I just think they need to be as light as possible in order to be great. When carrying an HD camera, I think the larger prop size will be better. Cheers!

[@flipfpv]

Those betafpv 0802 22000kv motors are strong but they're really inefficient. I replaced some happymodel 0802 22000kv motors with the betafpv versions on a 65mm whoop and the flight time dropped from over 3 minutes to around 2-2:15.

[@sketchpv3080]

Went above and beyond taking out the AIO and weighing it! I’d like to see a variant of this board built without the pin headers for a non-DVR ultralight build. My HappyModel Mob6 AIO just started acting up.

[@dubzsquaredfpv7171]

I too am excited about the flight controller. I really think the AIO FC is where they 65mm whoop should be. I'd be interested to see the performance with just a normal non-HD camera. I think Happymodel should have included a U.FL connector on the Mobula6 board like this one.

[@fpvcruzer]

Thanks for this review. I have a meteor 75 and was thinking of getting the hd camera and dvr setup that betsfpv sells (which I think is the same one that is in the meteor 65 hd. I was holding off because of concerns over a big decease in flight times... perhaps I will buy the 65 hd and transfer it to my extra meteor 75 frame!

[@fpvcruzer]

I bought a Meteor 65 HD and put it on the Meteor 75 frame and it works great! For anyone considering putting the Meteor 65 Hd on a 75 mm frame I preferred the Meteor 75 frame over the Mobula7 v2 frame because the Meteor 75 frame had screw holes for the canopy, the Mobula v2 frame did not. This was a super easy upgrade Thank you Mr Shutterbug for recommending it.

[@pranavasthanaDelhi]

Nice video! Thanks and hope you are doing great!

[@djs134]

Solid video as always. I can’t wait will they sell the new meteor75 lite frames

[@MrShutterBug]

I asked them about that. Waiting to hear back.

[@djs134]

Mr ShutterBug wow , awesome and ty. I love how the new frames ducts are deeper to completely encapsulate the props like how any other 65mm frame does. I’m using a fpvcycle board with nbd 0703s in a mobula 7 frame with gnb 450s and omg is it amazing. I’m getting over 4min of crazy freestyle or racing flights. All I need is a better frame. I’m not as comfortable flying around the kids with this much prop exposed. Have a good weekend and ty for the reply

[@stylesuxx]

I have tested the BetaFPV Nano HD - the latency threw me off completely, and I built a small test rig to measure it - I had an average latency of 40ms and a maximum latency of 80ms. Flying indoors was super frustrating for me - although I flew an 85mm rig. Really like the AIO board - looks promising, wondering about its longevity...

[@amirkabiri6870]

Hi i really enjoy watching your videos

[@andrewgilbertson4226]

Great video, it helped me decide to get the Meteor65 HD as my first FPV quad! My plan was to use it as a "newbie's first cinewhoop" and practice for the eventual bigger quad with a better camera, but I've found the camera angle is very high for low speed flying indoors or proximity flying outdoors. Do you know any hacks (or parts) that would let me lower the camera angle?

[@MrShutterBug]

Good question. If you know someone with a 3D printer, then there are tons of whoop canopies on Thingiverse that can be printed. There are other canopies you can buy too, but I’m not sure which of them would fit the Nano HD cam off hand. Good luck!

[@andrewgilbertson4226]

@@MrShutterBug Thanks for your response! Since replacement canopies are so cheap, I ended up shaving a bit off the front of the spare and tying it down to the front of the frame with a twist tie. It looks like a hack, I can see the frame in the very corners of the image (this will likely not be noticeable once I stabilize), but the lower camera angle makes a WORLD of difference for my control. Now I'm easily flying under chairs and landing the quad on my lap.

[@addisonnugent1840]

Hi I just got the Meteor65 Acro. I binded it last night, flew around a little. Then flew a couple batteries this morning as well. However when I plugged in a battery about an hour later, all I get is red light and purple blinking light. It doesn't bind and I don't think it even makes it through the boot up sequence because there are only three beeps when I plug in the battery and nothing else. Is there any chance you might know the issue? Thank you so much

[@NoiseBoysGarage]

I just rebuilt my meteor 65 . But I like the 75 mm platform. I only worry about burning out the motors . Ima give it a try . I have the parts to convert over . Thanks 🙏🏽

[@fpvcruzer]

How did your conversion go? I just converted mine and also felt a bit of concern about the motors but after about 10 batteries I think I will be fine. It isn't a racehorse but a very nice cruiser with plenty of speed for ripping around my yard.

[@NoiseBoysGarage]

Lol that was months ago . But yeah I’m still flying it . I left my 65 beta kwad alone and converted my 65mm acrobee to the 75mm with only a mobula 7 frame and new 40 mm props . Great flyer I definitely like more then the 65 but that’s just me

[@fpvcruzer]

@@NoiseBoysGarage oh! You left your meteor 65 alone. I misread your post. It is a fun drone converted or not. I own a meteor 75 and the converted 65hd has a lot less punch which actually works better for flying low and in and out of obstacles in my yard..

[@GiffysChannel]

I'm curious if Drone Mesh tests the camera latency.

[@kaelstokes5804]

I just bought the beta65s and I have a betafpv bayang radio transmitter they both have D8 and I just can't seem to bind them together can you help me with this?

[@officerrage]

Thank you for the great review! Do you fly Acro or Horizon/Angle mode indoors?

[@MrShutterBug]

Thanks. I fly both. The indoor footage is angle mode, the outdoor footage is acro.

[@recycl0ps890]

Awesome video. I’d like to change the frame and motors also. I own the beta 75 lite from advance kit 2... can I just swap out the flight controller between these?

[@MrShutterBug]

Yeah, the FCs are the same size. You can swap all the Meteor65 HD parts into the 75mm frame. All you’ll need then are some 40mm props to fit the 1mm shaft of the 0802 motors. 👍

[@recycl0ps890]

@@MrShutterBug could I use the motors and battery from the advance kit? 450 mAh battery and 1102 Brushless Motors?

[@randov1991]

hello what firmware you use? and where to find cli file for that.

[@MrShutterBug]

It came with Betaflight 4.2.0. I flew it using the tune that Betafpv provided. If you need the factory CLI settings, you can find that here: support.betafpv.com/hc/en-us/articles/900005728906-CLI-for-Meteor65-HD

[@jairoortega7366]

Hi Nate, good video as all you upload. I have a question about the FC its is posible add a Frsky reciver..? I boutgh a meteor 65 two days ago with this FC and I can´t go around other rooms on my appartmet because I los signal with mi remoute controler .... I have a cetus Pro and 85 Pro 2 and dont have this problem with them.

[@MrShutterBug]

Is the Meteor65 HD the one that has bad range? First, I would check the little red antenna. It might be sandwiched between the FC and the DVR board, or it might be flying flat along the FC. You could try angling the antenna away from the rest of the electronics and make sure that the red antenna is as straight as possible. Sometimes I even put the antenna outside the canopy so it can go straight up. I don't know exactly which FC you have, because betafpv has made so many FC and they change which ones they are shipping sometimes. If the FC has a solder pad for SBUS, then you can wire in an external FRSKY receiver. For myself, I've been using ExpressLRS on all my newer builds. The range is fantastic and the gear is pretty cheap. Good luck!

[@jairoortega7366]

@@MrShutterBug First thanks, I appreciate your answer.The Meteor 65 i bought has the F4 1S AIO FC(SPI Rx) that is on their page of Meteor 65, that have pins whit RX1 and TX1, but i dont know if i can try to solder in a new reciver.?.... beacuse I moved the red antena out of the frame and did not work. Im new on this hobby, that why I stil don´t have an Express RLS RC.

[@BrandonBeans]

The most interesting thing about this is the new flight controller. I've been really happy with the Crazybee Lite boards, but the range kinda stinks without tinkering, so I may have to test this betafpv one out. My one hangup is last two betafpv boards I've bought had gyro drift out of the box (1 barely noticeable, 1 completely unflyable). Have you ever experienced this?

[@MrShutterBug]

I had a gyro go bad on a Crazybee Lite once. It was so bad the drone would just flip over. I have not had the problem on BetaFPV boards, but that is probably just luck. They use the same MPU6000 chip, so I don’t think it is really the fault of either company.

[@BrandonBeans]

@@MrShutterBug It probably was bad luck, but I still have a bad taste from fact that I got ghosted by BetaFPV support on the matter. I ended up returning $140 worth of BetaFPV stuff to RDQ after waiting for a week for response.

[@MrShutterBug]

Brandon's Baked Beans sounds frustrating. I don’t blame you.

[@grege2383]

As much as I love my meteor65 and 85 Pro 2 I've had nothing but problems with them. When they fly, they fly great but I've had 2 85 Pro 2 where when changing the battery after a regular flight it wouldn't boot up.

[@Holyfield]

Hello again Mr. ShutterBug! Were you able to get RPM Filtering working on this Drone? Ive flashed the latest JESC Firmware with Telemetry but no matter what I try the Drone wont arm. I also noticed that the ESC shows up as O-H-5 in BLHeli but on the BetaFPV site its advertised as O-L-5. Ive wrote BetaFPV support already but they are pretty slow with the replies. Thanks!

[@MrShutterBug]

What it says in BLHeli is the real thing. There is no version of the Meteor65 HD that has "L" type ESCs, but the first batch of non-HD Meteor65s did. They probably just copy-pasted that part of the specs on accident. But even the "L" type ESCs can do bidirectional DSHOT if you use JESC 2.3. If you have JESC and you paid for a license, and you flashed telemetry on the ESCs, then I'm not sure what would stop it from working. Are you sure bidirectional dshot is what prevents it from arming? Is that what it says on the OSD?

[@Holyfield]

​@@MrShutterBug Yes I double checked JESC "ESC 1: JESC-OH5-48 (2.3) with Telemetry (2.3) - activated, licensed". When I turn on "bidirectional dShot" in Betaflight I get a "RPMFILTER DSHOT_BBANG" warning. I also dont hear the final beeps when I boot up the drone anymore. Really strange since I dont have problems with my other drones, including the regular Meteor65.

[@inthewindfpv644]

hi! i have a problem with it, i can´t acces the VTX and at the time of watch throught my goggles (hdo2 ) it lonely changes the channel in the Same Band. do you know how can it happens? thanks!!!

[@MarkFisch]

To get the video off the drone do u need to remove the SD card or can u plug the drone into the PC to grab the footage. Thanks

[@MrShutterBug]

Yes. Remove the MicroSD card to get the HD footage from the drone.

[@MarkFisch]

@@MrShutterBug thanks for the reply doesn’t matter drone wasn’t flying correctly and now the ESC failed and I got a new board and that one also failed. My third one comes in tomorrow so hopefully it’s good. I need a recommendation on an easy cinawhoop that flys. All these KZbin videos I’m confused lol

[@jedovcela840]

What drone is the one on the left top corner in 0:45 ? Looks interesting

[@Max_0578]

I think it is his new babytooth build

[@MarkFisch]

Do u have a link to the update u made to the drone with the 75mm

[@MrShutterBug]

I have not made a video about this specific drone converted to 75mm, but I have built quite a few 75mm whoops with the same size motors. My favorite 75mm whoop is this one, which I made extra light: kzbin.info/www/bejne/ZoGWgYV7grCXesU

[@pelipelilg2]

I've been a week with my new meteor65 HD (1s), but it has a lot of vibrations, I have activated the rpm filters and it follows the same problem. Please, can you share your diff all? I am very desperate. Thanks you my friend

[@25JoaoRafael]

Hello, how do I configure the LEDs?

[@MrShutterBug]

Using the LEDs tab in betaflight.

[@25JoaoRafael]

@@MrShutterBug about the led I still don't understand how to use it. The tutorials are everything for a 5 "drone with lots of LEDs. But thanks

[@MrShutterBug]

@@25JoaoRafael it works the same as a 5” drone except that it only supports 2 addressable LEDs. If you have more than 2 in betaflight, the others will be ignored. You also have to make sure LED Strip is enabled on the Configuration tab.

[@andrewpalana8073]

Hi Mr. ShutterBug I'm new to FPV drone and just want to ask do I have to register this small drones to FAA?

[@MrShutterBug]

No. In the United States, you do not need to register with the FAA unless the drone weighs 250 grams or more, in the air.

[@andrewpalana8073]

@@MrShutterBug Thank you

[@DOHCtorMiguel]

If you move everything over at 75 frame does it matter if I use 3 or 4 blade props. I can't seem to find 3 blades any where. Also could I get away with using 1102 18000 kv motors? since I have extras laying around

[@MrShutterBug]

For 0802 motors, I would suggest the gemfan 1635 3-blade props with 1mm shaft (bit.ly/2TFy9aE) or the HQ 1.6x1.6x4 (bit.ly/3mGOqbP). You could even cut down those HQ props to make light 2-blades, like I showed in my most recent video. 1102 18,000kv motors are OK, but I personally prefer to the lighter builds. If you go with 1102 then I recommend using the most aggressive 40mm props you can find. Otherwise, the extra torque will be wasted. So for 1102 I would use the 4-blade version of the gemfan prop (with 1.5mm shaft), or if you can find them the old style of prop is actually really good on 1102s. I'm talking about the style they used back when the 75X first came out (bit.ly/2TJTP5y). Cheers.

[@DOHCtorMiguel]

@@MrShutterBug Thank you. The 3 blades are on back order. I tried the 1102s with the 3 blades I had (40mm) but I didn't like the handling and I barely got another 30 secs. I went back to the 65 frame for now.

[@omidmohajerani]

tnx for the review

[@25JoaoRafael]

is it possible to install an external vtx on this fc?

[@MrShutterBug]

I believe the answer is yes, however, you might not be able to get OSD. You would need to wire the camera signal wire to the external vtx instead of wiring it to the FC. Your external vtx won’t have smart audio unless there is a free UART for that (I can’t remember if there is). Also, if you use an external vtx then you should disable the internal vtx or put it in pit mode to avoid interference & heat.

[@25JoaoRafael]

@@MrShutterBug Thanks for answering, I understood and I was thinking this, but as the betafpv did external rx I thought I could have an external vtx. But thanks

[@glytch5]

I keep getting RX disconnected, and VERY bad video range... like extremely bad. I bought the frsky version but could not bind my remote to it without changing betaflight to say "frysky_D" instead of "frsky_x" Do you know what the difference is, and is this why my range is so horrible with the receiver? Thanks!

[@MrShutterBug]

FRSKY_D is the D8 protocol. FRSKY_X is D16. Your radio has to use the same protocol or it won’t work. The FC has a little red RX antenna. It might be pressed against to FC or the DVR board might be blocking it. If so, you might get some additional range if you make the antenna stick straight up (outside the canopy). Good luck.

[@glytch5]

@@MrShutterBug i'm using the literadio 2 which should support both.. however the d16 did not work at all for binding. The sku on amazon said frysky lbt. Isn't the big antenna out the back the receiver for rssi? And the little baby one inside for the VTX? Thank you for the answer. I am going to try the antenna thing.

[@MrShutterBug]

@@glytch5 there are two versions of D16: LBT is sold in Europe and the FCC version is sold in USA and elsewhere. I believe the Lite Radio 2 can broadcast either version of D16, if switched into the right mode, but I believe the drone can only receive one version. They have to match. D8 is simpler. It is the same everywhere.

[@glytch5]

@@MrShutterBug Thank you. I wanted to make sure... if it bound to d8... then its a d8 receiver right? I'm not loosing something by not being able to get LBT or d16 to work am I? If so... I may need to go back and try some more things. That kinda through me off that I had to turn on frsky_D and it came set to frsky_x

[@derecktaitt8457]

Great review I have this drone the only problem is the props fly off most of the time when I crash

[@MrShutterBug]

Try getting some other Gemfan props (not the white ones from BetaFPV).

[@derecktaitt8457]

Thanks for the advice muchly appreciated

[@markus9666]

FrSky ACCST v1.x or v2.x? Given its advertised also as LBT I trust it comes as D16 SPI Rx?

[@MrShutterBug]

It supports D8 or D16 (FCC vs LBT depends on which version you buy). I'm pretty sure it's the older protocol not the newer one used by the ACCESS radios (because those only work with FrSky branded radios). I fly all my whoops in D8 mode because it has 9ms less latency than D16. Cheers.

[@MCHeli]

Which chips are used in the ESC: BB1 or BB2?

[@MrShutterBug]

BB2

[@thongdtk3]

I wonder why the quality of your video from meteo 65 is so good

[@MrShutterBug]

This isn’t a normal Meteor65. This one has an 1080p DVR built in.

[@GiffysChannel]

I like your Oculus shirt. Do you see VR and FPV coming together in the future?

[@MrShutterBug]

Who knows! VR is great too!

[@ktmjay9920]

Great video 👌

[@BryonCLewis]

Can you set the mW to higher than 25 on this board?

[@BrandonBeans]

Good question. The crazybee lite can push out something like 250 mw and doesn't even get hot, although I keep mine set to power level 2 (default setting) which works out to about 150 mw (and I have low power disarm on just in case).

[@MrShutterBug]

It is advertised as 25mW. I haven’t tried cranking it up, nor do I have the tools to verify the output. The CB Lite does indeed have a powerful VTX, but the CB Lite has a poor antenna. If you want to get the best reception you need a good antenna (on either board). One side note about the CB Lite, I’m told that even the “25mW” setting is closer to 50mW true output, which is cool unless you are in a race where 25mW is required.

[@BryonCLewis]

@@BrandonBeans just wondering because I built a nice 1s ion zero grav using the mobula6 fc and without upgrading my goggles and getting a middle the video seems to be the limit on my range. For reference using ev800dm and a betafpv lite radio 2. I noticed that newbeedrone has a 1-2s fc that I think can go up to 100mW.

[@BrandonBeans]

@@BryonCLewis you can turn it up using smart audio in OSD.

[@flipirider22]

Hi! How do you bind it? It is being Imposible for me. Thank you

[@zachmachina]

How is the latency compared to the Mob6 HD?

[@MrShutterBug]

I believe the Mobula6 HD has better latency then the Meteor65 HD, but I don’t know the numbers off hand.

[@zachmachina]

@@MrShutterBug wow quick reply! Thank you! I'm less interested in actual numbers than I am just knowing if there's a difference. That's very helpful, thank you!

[@jermadjesty]

Do you have a favorite 1s board?

[@gonebdg]

Mobula6 HD looks better for me, the Runcam split 3 lite is better than the Caddx Baby turtle lite which I think was used or adopted by betafpv for this Meteor65 HD. Not sure about the motor, which one is better ... the New Happymodel EX0802 or BetaFpv 0802SE ?

[@lis739]

Does it bind it with futaba?

[@MrShutterBug]

There is a version of the drone made for Futaba. You just have to select that option when ordering: bit.ly/meteor65hd

[@arnobvlogs2862]

Nice..

[@MrShutterBug]

BLACK FRIDAY EXCLUSIVE: If you want anything from BETAFPV, I can save you 25% on your whole order! Just copy the following link and code, then use them between Nov 27 - Dec 1. It is an affiliate link, so it helps me out if you remember to use it. Thanks. Link: bit.ly/2ZuZ4Xc Discount Code: Nate25Beta

[@blastofffpv]

At least with mob6hd the fpv latency is sdcard and framerate related. With a sandisk extreme pro and 1080p30 it’s pretty ok in my case.

[@MrShutterBug]

I haven't tried recording at 30 fps. Doesn't that make your FPV video 30 fps as well? I know the other Caddx Turtle cameras do that and it feels much worse while flying than 60 fps. I also have not compared different card speeds, so that's an interesting point too. I was using a SanDisk "Ultra" 32Gb card.

[@blastofffpv]

Mr ShutterBug There’s definitely something wonky that maybe could be solved with a firmware update. For eg, even without the sd card the latency is there, maybe it uses it to cache memory or something weird. (Mobula6HD)

[@aythixfpv]

Conversation to babytooth video!!!!!!!!!!! Edit nvm due to the 75mm build.

[@irisshi2731]

hi NIce video!

[@alexmoil6256]

Dear Nate, Always apreciate your vidéos ! My shutterbug 85 always in the air, with the new caddx ant, way better video

[@MrShutterBug]

Awesome! I've put the Ant on a few more builds now! It's SO good for the price & weight! Have fun.

[@jacquemeier2005]

Hack this algorithm! Whoop yourself in the top ten! :)

[@paulterl4563]

Hi

[@JoshPaynter87]

Got any free drones you want to give away?

[@MrShutterBug]

Yes actually. I'll probably do some give aways in the future. Too many are collecting dust right now.

[@engizmo]

hi

[@Cre8ionz.]

Still they haven't heatshrinked the end of the VTX Antenna 🤦‍♂️ If it breaks, video range will be very bad..

[@whoopsquad]

I think I’ll pass.

[@MGozz]

Yeah, I kind of just want the FC for a racing build myself. Looks like it is better than the mob6 aio.

[@Sackenstein]

Hi