MicroVision REVISIT With a Little HELP From My Mate VINCE

  Рет қаралды 38,111

StezStix Fix?

StezStix Fix?

Күн бұрын

Пікірлер
@Mymatevince
@Mymatevince 3 жыл бұрын
Hahaha, that was a fun video...apologies for the hair, at least it was a white one, I don't mind losing them. So on my one I changed out the 4 pin voltage regulator to make it work. I didn't film the revisit, but it was just bugging me what the original fault was. I believe these were prone to problems from electrostatic discharge, so maybe that might have been the fate of your one???? I wonder if the resistor trick would work on the faulty chip like it works on some of the Sega Mega Drive games. It would be interesting to see a diode reading with the red probe on ground, and probe each leg of the chip with the black probe to see if one may have a different reading from the working chip. Might not work in circuit though??? Glad to see your one working again. Thanks for the kind words and keep up the great work. Fantastic video Steve 👍👍👍👍
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Vince! That's a good shout regarding the resistor trick, I didn't think of that! I'll definitely test the chips and see if there is any difference. I think it will be a good learning exercise for me! I assume that chip is just responsible for driving the rows and columns of the LCD, so i wonder why yours had a few pixels missing? I did spot some trace repair work, so perhaps one or two of the chip legs weren't making a proper connection? Not sure, but it would definitely be interesting to see if my faulty chip could be saved and perhaps put back in to your one! 👍 thanks again for your kind gesture, Vince 👍
@MyklBlue69
@MyklBlue69 6 ай бұрын
Good man for sending this to Steve, Vince! 👍
@Rocky1138
@Rocky1138 2 жыл бұрын
Desoldering gun at regular speed: cow Desoldering gun at 2x speed: lamb
@ToxoRetro
@ToxoRetro 3 жыл бұрын
Stez & Vince, thank you for your persistence. It's a shame that this wasn't a "true fix" as such, but at least between you, the culprit component was found ending the project with a conclusion. There's something satisfying about knowing you did 100% all that you can do.
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Toxo! Yeah, a shame about that chip, but I might have another look at it off camera and see if there's anything that can be done with it, I'm not overly hopeful, but I'll likely learn something new so it'll be worthwhile! 👍
@TheCod3r
@TheCod3r 3 жыл бұрын
Great repair Steve! Great to see you working with the legend too by the way. I feel you've got that soldering technique down now too, absolutely awesome 👌
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks mate, appreciate that! It was really good of Vince to reach out and help me out. He is 100% the legend. Cheers 👍
@DanBird
@DanBird 3 жыл бұрын
Another fantastic video. Interchangeable games on a device over 40 years old is amazing.
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Dan! It's crazy, isn't it? To think that this was manufactured 10 years before the Game Boy! 😲
@tjmarx
@tjmarx 2 жыл бұрын
My favourite part of this video (other than your singing) was when you went to all the trouble of putting stickers on the shells only to immediately remove everything from inside them thus defeating the purpose.
@Beaps73
@Beaps73 3 жыл бұрын
Can I just say. I watch a lot of YT vids and most come across fake. I truly believe you are such a down to earth bloke and enjoy your vids no end.
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Beaps, I really appreciate that mate 😊. Nothing fake about Captain Bodge! I genuinely only do them for fun, and hopefully that comes across! 👍
@pedromimoso8804
@pedromimoso8804 3 жыл бұрын
Captain Bodge and his gun! Ta-ta-ta-da! Awesome work and awesome (and generous) collaboration. And every day improving your skills. Keep it going, Steve!
@StezStixFix
@StezStixFix 3 жыл бұрын
Haha, thanks Pedro! Really appreciate that! And yes, a very generous donation from Vince! 😍
@Rocky1138
@Rocky1138 2 жыл бұрын
Steve: please consider adding a socket any time you have to take an integrated circuit off to save time and sanity. Doesn't always work because you might not be able to get the plastic shell back on, but many times there is room.
@Tidder007
@Tidder007 3 жыл бұрын
Nice! Desoldering/resoldering that chip must have been fairly time consuming, I likely would have given up after half through the first row. Good work, this was awesome. Literally gasped when the chip popped up and the pin bent. I thought that was the end for all of us! As always, very entertaining and impressive.
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Tidder! Yeah, the chip off Vince's console was a little harder to remove as I think he'd had it off before. But the other one came off so easy! I love that desoldering gun, it literally saved me about an hour of wicking and solder sucking on this! 👍
@MicroMageRepair
@MicroMageRepair 3 жыл бұрын
Nice work, and nice assist from VINCE!
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Micro. Much appreciated! 👍
@JoeyDoesTech
@JoeyDoesTech 3 жыл бұрын
Name me a better duo than Steve and the solder removing gun. Great little repair pal!
@StezStixFix
@StezStixFix 3 жыл бұрын
Haha 😄, cheers mate! Really good to get this one working. 👌
@chris-pike
@chris-pike 3 жыл бұрын
Good to see this repair with help from Vince there Steve another interesting video you did there Steve keep them coming - Nice 1 👍
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Chris! 👍
@jinxnatorx
@jinxnatorx 3 жыл бұрын
Yes Captain Bodge is here 🙌
@StezStixFix
@StezStixFix 3 жыл бұрын
The long-awaited return! 😂
@jinxnatorx
@jinxnatorx 3 жыл бұрын
@@StezStixFix For sure and you got to fix it 🥰
@guywilton7471
@guywilton7471 3 жыл бұрын
Steve.....the singing at the start & end.....what have we said about going to the pub before working on electronics???????
@StezStixFix
@StezStixFix 3 жыл бұрын
Hahaha 😄. That is a very good point, Guy! Never drink and bodge! 😊
@blueskies792
@blueskies792 Жыл бұрын
Stez, a copy of that chip can be made. @11:09 you should learn how to read/write chips. Its not that hard. TL866II kits are cheap and can be used to read and write many chips.
@KorAllRBare
@KorAllRBare 3 жыл бұрын
There were a lot of Dry solder joints connecting that chip and there is still some that I think need reflowing all over the PCB "A Dry solder joint usually looks dull and crackled and if you find any it's good practice to reflow them with fresh flux and solder", As it may actually be the cause of the problem, Yerp... Your chip may actually still be OK, Only way to find out is to plug it in to a soldered in "IC Socket" into My Mate Vince's one and plug yours into it. 😉 "Record the attempt just in case" And if it works you can let your viewers know why the chip didn't work in yours and why it now works in My Mate Vince's "Cause was Dry Joints". This is a Tip.. If you are going to replace through hole IC's "IC with pins going through the PCB" It's a good idea to first solder in an IC socket and then plug the replacement Chip into that Socket..
@ToxoRetro
@ToxoRetro 3 жыл бұрын
Fair shout; worth a go. 👍 Can't make it any worse. 😜 Also, the IC standoffs are a brilliant idea! 🤘😎 I'd long forgotten about these things. The less times heat is applied to the chip, the reduced risk of burning it out. Often the best ideas are the simplest, and often overlooked.
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks 🐨! I'll definitely do that, thanks for the advice. I did actually buy some of those sockets when I was working on a megadrive a few months back. I completely forgot about them! I'll give it a go. Thanks, as always! 👍
@555geoneo555
@555geoneo555 3 жыл бұрын
Great video Steve 👍
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Geoneo! 😊
@CS-rk6fu
@CS-rk6fu 2 жыл бұрын
You killed that kazoo mate mate
@N1ickem4n
@N1ickem4n 3 жыл бұрын
Another entertaining video Steve! So, I may have missed it, but how did you come up with ur channel name? Curious! 🙂
@StezStixFix
@StezStixFix 3 жыл бұрын
Thanks Nicklas! StezStix is my nickname from my early years. To be honest, I'm not entirely sure of its origins, but there is a drummer in an English band called The Macc Lads with the same name! 👍 All a bit weird, I know! 😁
@N1ickem4n
@N1ickem4n 3 жыл бұрын
@@StezStixFix Nah, not weird. Just fun to know where people takes their names from. Some names are weird for sure tho. 🙈🤣
@StezStixFix
@StezStixFix 3 жыл бұрын
That is very true! 😁
@Dukefazon
@Dukefazon 4 ай бұрын
9:50 - lifted trace on the top row? :S Pro tip: don't force out chips like that. Once you sucked away all the solder you can just apply some heat with a heatgun along the legs and it should lift out without the need to force it.
@TheDemoniusX
@TheDemoniusX 2 жыл бұрын
The sped up solder remove sounds like "Mini me" fron't Austin Powers XD.
@JT-il3fe
@JT-il3fe 2 жыл бұрын
Nice let’s go!
@DForce26
@DForce26 2 жыл бұрын
Great vid! just one note, though... Maybe clean your soldering iron once in a while :p
@Mephiston
@Mephiston 2 жыл бұрын
Its funny how both boards have stickers that says "boobss" on them
@jessragan6714
@jessragan6714 Жыл бұрын
A question. Are any of these parts still available, or do you have to filch them from existing systems? My Microvision doesn't want to power up... there's no screen, no sound, nothing. I'm thinking (hoping) that it just needs the switch replaced, but I don't know if that will solve its problems, and I don't know how far I want to go to repair such a simple system.
@dlarge6502
@dlarge6502 2 жыл бұрын
Now, was it the chip? or was it the solder joints on the old chip?
@kennethbarker852
@kennethbarker852 2 жыл бұрын
1st class video to watch thank you take care kind regards from me kenneth🍇🍈🍉🍊
@mistie710
@mistie710 2 жыл бұрын
"And Bully's special prize..."
@logothaironsides2942
@logothaironsides2942 9 ай бұрын
yeah! it actually doesnt seem a bad game. Always did like those off the wall games. Back in the day when a game machine literally had one game ,these interchangeable fronts must have seemed state of the art.
@tumbles8350
@tumbles8350 2 жыл бұрын
I was shocked to learn that mymatevince has hair, I always imagined he was techmoans twin
@jivillain
@jivillain 2 жыл бұрын
TOO HANDSOME
@OOOHBILLY
@OOOHBILLY 2 жыл бұрын
WWWOOOOWWWWW, ruin Vince’s game. Unbelievable. Lololol jk. He’s a champ for sending it out. Nice work!
@HillbillyRestoration
@HillbillyRestoration 11 ай бұрын
Is that hair still available for sale?🤩🤩
@jeffcarriere
@jeffcarriere Жыл бұрын
👍👍👍👍
@zarrow50
@zarrow50 2 жыл бұрын
I think the girl next door has a de soldering gun
@eclectarama
@eclectarama 3 жыл бұрын
Your solder removal machine sounds somewhat like a macerating toilet...
@StezStixFix
@StezStixFix 3 жыл бұрын
🤣 haha, it sure does! 😆
@davebrooks993
@davebrooks993 2 жыл бұрын
Your solder joints are way too shiny, tone it down a bit, you’re starting to affect my self confidence. Great video!
@StezStixFix
@StezStixFix 2 жыл бұрын
😂😂 thanks Dave!
@wolfcanine100
@wolfcanine100 Жыл бұрын
just wondering where you got the replacment chip from. im trying to fix a few
@kenRoberts1984
@kenRoberts1984 2 жыл бұрын
MOO
@Cluffo11
@Cluffo11 3 жыл бұрын
How much for the hair? Asking for a friend.
@StezStixFix
@StezStixFix 3 жыл бұрын
I'm gonna put it on eBay.
@SimonEllwood
@SimonEllwood 2 жыл бұрын
Your soldering is not how I was taught back in the day. You should feed the solder into the joint, not the iron. The easiest way to do that is to put the iron on one side of the joint and feed to solder into the other side of the joint.
Trying (AGAIN) To FIX This Toshiba TV With NO POWER | Revisit
19:56
StezStix Fix?
Рет қаралды 119 М.
Bringing MMV's MicroVision Back From The DEAD!?
19:21
StezStix Fix?
Рет қаралды 48 М.
How Strong Is Tape?
00:24
Stokes Twins
Рет қаралды 96 МЛН
eBay CUSTOMER RETURN BOXES - Can I FIX Them?
54:56
My Mate VINCE
Рет қаралды 286 М.
Broken META QUEST 2 VR Headset - Can I FIX it?
53:18
My Mate VINCE
Рет қаралды 55 М.
Prior REPAIR Attempt Gone WRONG! | Can I FIX It?
12:23
StezStix Fix?
Рет қаралды 111 М.
This BAR Keg Font Doesn't LIGHT Up! | Can I FIX It?
15:02
StezStix Fix?
Рет қаралды 64 М.
This small CRT monitor is less than 2" thick
31:45
Adrian's Digital Basement
Рет қаралды 344 М.
More More MORE AMAZON RETURNS - Can They Be FIXED?
44:13
My Mate VINCE
Рет қаралды 180 М.
This SNES Game is Worth Around $400 IF I Can Fix It!
20:18
TronicsFix
Рет қаралды 779 М.
USB Voltmeter BROKEN by BALD HEAD MACHINE - Tea Break Fix
22:49
My Mate VINCE
Рет қаралды 42 М.
This AMAZON FIRE HD 8 Doesn't Charge | Can I FIX It?
18:41
StezStix Fix?
Рет қаралды 53 М.
FULL VERSION | FAULTY Game Boy COLOR | Can I FIX It?
1:00:08
StezStix Mix
Рет қаралды 53 М.