HUGE PROBLEM - Polaris Ranger 800 900 1000 - Rear Axle CV Joint Replacement - Back Noise - Boot Rip

[@BlackDrinkFilms]

Good stuff. Replaced mine by using this video. Made it very easy and saved money.

[@MidNebraskaMotorsports]

Love to see comments like this. Let us know if you need anything: www.ebay.com/str/midnebraskamotorsports Hit that subscribe button if you get a chance.

[@taylorford1807]

Lil' spider made an appearance at 10:16 and crawled up into the knuckle. LOL. Great vid.

[@MidNebraskaMotorsports]

Hahaha. So I've been told. Thanks for watching & the comment. Let us know if you need anything: www.ebay.com/str/midnebraskamotorsports

[@escott1140]

💯The exact info I needed without any fluff content. Thank you✌️👍

[@MidNebraskaMotorsports]

For sure! Let me know if you have any questions. Thanks for watching and the comment! Check out this kit that is on sale now! amzn.to/3RbDjIV

[@timmytool1231]

Thanks, help a lot. One thing I might suggest is jack stands, my buddy has his Rzr 1000 fall over on him crushing his foot while doing the exact same job.

[@timmytool1231]

@@MidNebraskaMotorsports Welcome, right after watching your vid I started on the axle job on my 900, I had put jack stands under the frame on both sides, did one side then decided to do the other the next morning, when I came out my motorcycle jack had bled off the pressure and was laying flat, the rig was just sitting on the stands, good thing for the jacks otherwise the rig would of come down on the rotors. I will subscribe, and again thanks for the vid it was much help.

[@KJMJ1228]

Made it a little harder taking the rotor off. Just take top bolt out and then axle will come out. Saves a little time

[@MidNebraskaMotorsports]

Thanks for the comment! And for watching! Subscribe to catch more on the Quadrunner 250.

[@erikbaker3818]

Looks like you were in a race to get this done, but my recommendation is to use some type of anti-Cs on the axle ends

[@MidNebraskaMotorsports]

I hate wasting time! Thanks for watching and the comment. Check out: kzbin.info/www/bejne/hIfGf6h4nrp_fMk . This is one of our best Ranger videos. Let us know if you have any questions!

[@terrytrank4237]

I have two battery in my 2012 polaris 500 side by side how do I keep both charge with a trickle charger.

[@MidNebraskaMotorsports]

Terry. I would build a jumper lead or if you'd like to add another trickle charger, you'd be able to charge the batteries quicker. This is the best trickle charger on the market! amzn.to/3DeYQKy

[@terrytrank4237]

Thanks

[@JeffSnyder-v3z]

Nice video. Thanks

[@MidNebraskaMotorsports]

Happy to help. Thanks for watching and the comment. Let us know if you need anything: www.ebay.com/str/midnebraskamotorsports

[@Dxpa1980]

How do you tell if the axel is going bad?

[@MidNebraskaMotorsports]

If it is making noise or slipping. Thanks for the comment! Let us know if there is anything we can help with. Check out: kzbin.info/www/bejne/jmGklXmuoK-chck for more tips. And: www.ebay.com/str/midnebraskamotorsports for all your parts.

[@travisroy7122]

i see you used a hammer to put the axel in what would make it pop off of there well driving because i just had it replaced and drove it a week and it popped out?

[@gwgillman1]

whenever I pull a axle,I always use antisieze in the threads just makes it easier if you ever have to pull again,good video though

[@scottmilton6766]

Thank you

[@MidNebraskaMotorsports]

For sure!! Thanks for watching & the comment. Let us know if you need anything: www.ebay.com/str/midnebraskamotorsports

[@chrisdove7362]

Do you use anti seize on the spline

[@georgemartens8158]

Good video thank you

[@MidNebraskaMotorsports]

Thanks for watching! Check us out on ebay: www.ebay.com/usr/midnebraskamotorsports

[@chrisdove7362]

What brand axles.Use Oem

[@donbrunski3840]

I heard a loud pop and now my passenger side rear wheel won't engage. What do you think broke?

[@themarcel6.6]

Same here. Find Out anything?

[@hav1byte]

nice, but dont need to remove the lower bolt on the nuckle, just the top and it will flop over and easy to remove the axle

[@MidNebraskaMotorsports]

That might work, but you are really taxing the boot at that point. I've seen boots splits while trying your trick. Hope it keeps working for you though! Thanks for watching and the comment. Let us know if you have any questions or need parts: www.ebay.com/str/midnebraskamotorsports

[@daveharding5874]

How do you diagnose if the CV joint is bad? Can you do a video diagnosing the problem? You mentioned clicking, but I'd like to know more.

[@ronburnside3790]

good job thanks

[@MidNebraskaMotorsports]

Thanks!

[@skulldaddy8431]

just curious why you tighten with an impact wrench and do not check torque values. Good video

[@hailystaton4242]

What is the best way to remove the front prop shaft on a 2015 900crew

[@couchrider6228]

You will have to drive the Roll Pin out and the two halves will slide apart.

[@bingobandit]

No need to take rotor or caliper off. Just take tire off, take top bolts out of A arm, loosen bottom bolts on A arm, take cotter key out castle nut off, swing hub down, pull axle, no need to deal with shock, reverse procedure.

[@Merritt3246]

What brand of axles do you use for replacements? Great video

[@gcnewd]

Great video. I was looking for just replacing the boot? how difficult is that?

[@gcnewd]

@@MidNebraskaMotorsports thank you.

[@ballzonurjaws]

Was there an answer here I’m in the same boat. Boot only

[@alphapackoffroad]

Grease everything before reassembly! Especially the axle end going to trans. And you didn't tighten that axle nut very much, will probably be replacing the hub bearing pretty soon after running it a couple miles.

[@alphapackoffroad]

@@MidNebraskaMotorsports not trying to correct you my friend. I've got a ranger and have experienced everything with it that can go wrong with a polaris all on one unit. I know you know your stuff, thats why I love your channel. Sorry if I came across as correcting you. Wasn't my intention at all. I use air impact not electric, and I and lots of others grease everything cause of what we ride in. If I don't grease everything then when I have to pull back apart, everything is Seased together and super difficult to remove again. Maybe I need to get me one of those electric impacts. And ill watch how I put things in a comment. Like I said I enjoy and respect all you do for us here on KZbin. My bad. Didnt mean to come off that way.

[@dirt_ripper8734]

Wheres the top CV boot?

[@patrioticrider8265]

Am I the only one that noticed the black widow go down the back up on the brakes at 10:11 - 10:18

[@MidNebraskaMotorsports]

Oh yea. I've had several comments on that. Thanks for watching and the comment! Let us know if you need anything!

[@teuvohannuksela4129]

How to replace a dry shaft on a 2014 RANGER 900 POLARIS

[@veronicadillard6729]

My 2013 polaris 800 efi the wheel locks up if I roll it backwards any suggestions on what that could be my gears are fine

[@porterwilson4665]

thanks gonna save me from the wraith of my parents

[@lucasretaud1226]

merci pour ta vidéo de France :)

[@whowasit1]

Anybody else see the spider coming down his web at 6:48 look close a the a-arm

[@kevinrisher7658]

Dude use some jack stands! Just saying. Be safe.

[@elkbow]

Screw the jackstands, it isn't going anywhere.

[@kfelix2934]

If it falls it's not going any where and he's not under it.