Mira Jump Multi-fit - Step by Step Installation Guide

[@johnhayes3094]

Just fitted my mira jump shower and there is buzzing noise coming from it any idea what it could be your help would be appreciated

[@mirashowers]

Hello @johnhayes3094, I'm sorry to hear that you've been having issues. Hopefully you've been able to speak with a member of the Contact Centre about this? You can chat with them on our Instagram, Facebook or Twitter chat or you can call 0800 001 4040

[@rickpuigmusic]

for the fixing brackets for the riser bar is there metal hardware available? The plumber that installed my shower said the plastic bits are rubbish and eventually break.

[@mirashowers]

The Mira Jump Multi-fit electric Shower - find out how easy it really is to replace existing electric showers in this step by step installation film

[@parsi4159]

i love this mira very good product!!!!!!!!! my house now on fire please send help

[@robertbailey8003]

Is the Mira jump multi-fit a straight swap for the Mira "Zest (J96F)". The water inlet is from the side and has a direct connection to the shower. Will I need any piping is that piping supplied?

[@mirashowers]

Hi Robert, Yes, Mira Jump Multi-fit is a great replacement option for the Mira Zest. You may need to adjust the pipework slightly up/down to match the old product footprint.

[@samnewman5129]

Can the water pipe be fed in from the top right at the back as my pipe comes from the top under Tiles and about 6 inch showing and close to wall so right side a must ??

[@mirashowers]

Hi Sam, the Mira Jump and Sprint models accept the water and electrical connections up to 36 different installation combinations. The water supply can be bought into the unit from the top left, bottom left, top right and bottom right to allow the easy replacement of most electric showers.

[@christophergizmo1486]

My Mira jump mk2 electric shower stopped working while i was using it ,a KZbin video helped me to diagnose the problem (solenoid)... After replacing the solenoid the shower works again, However it has developed a buzzing noise , I would be really grateful if anyone could give me some advice on what this could be and how to resolve it...

[@Tokaisho1]

Buzzing sounds to me like a loose connection on the solenoid, where you reconnected the wires, check the spade terminals are tight and not loose. You can use pliers to push these tight again and push onto the spade.

[@valeriewilliams4334]

I have a 7.5 Mira shower and sent for a 8.5 to replace. Can this be installed without any problems

[@mirashowers]

Hi Valerie, there will be some electrical work required. If you get in touch with our customer service team or speak to your local plumber they will be to advise exactly on what might be needed.

[@daveparnham3050]

We had a Mira shower installed by Rotherham council in 2010 now it's not working can you help please

[@mirashowers]

Hi Dave, sorry to hear your shower is currently not working. Have you been in touch with Rotherm council? The best thing to do is contact our customer service team who will be able to advise on the issue and a solution which may be a repair. You can find our contact details on our website, visit - www.mirashowers.co.uk/support/contact-us/

[@slickvicg]

My Mira elite st just broke and I need a new replacement can you recommend one for me please

[@redblade8160]

victor... Triton T80Z

[@derekbicki2383]

What about backplate fixing screws? Do I need to seal them with silicon against the water getting behind an electric shower?

[@mirashowers]

+Derek Bicki The Mira Jump is IP24 rated, so there’s no need to use silicone sealant on the screws or around the flush fit casing.

[@superhuman2753]

Hi.. I just replace my old elec shower with mira go.. But only cold water is coming out after all the procedures

[@mirashowers]

+Jay Jamero have you tried to contact our customer service team? They can be contacted on 0844 571 5000 they will be able to advise what has happened during your installation of the shower.

[@fypoetry]

hii.. my mira jump start button is not working well. i have to push it along using shower. if i don't push then the water is not flow.. how to fix it? thank you

[@mirashowers]

Hi Theresa, you can purchase a new button for the shower or there are a few other options. We recommend you call our customer service on 0844 571 5000.

[@belindasullivan5214]

just moved into a house with an existing Mira shower, the water pressure is rubbish, is there a way to increase the pressure?

[@mirashowers]

Hi Belinda, it depends on the shower and the water system in your new house. If you have a mixer shower you could potentially install a pump. Our customer service team will be able to provide advice. You can find our contact information here www.mirashowers.co.uk/support/contact-us/

[@mychannel0743]

This is more reliable than a Triton T80 Z

[@benregler9872]

Any shower is more reliable than a T80Z 😂

[@nstheboss]

Save yourself from terrible showers and do NOT buy this shower. It is terrible, in the winter you might aswell just have a shower under the garden tap, you'd get more water out of that. The pressure from this shower is horrendous. If you're on a budget, get a redring bright shower, that was my old one and was brilliant.

[@bigpappa43ish]

Wth