THE ultimate VESPA PLUG & PLAY pnp TUNING tutorial | FMP-Solid PASSion |

[@StoneCut]

Screwing the idle jet mixture screw IN makes the mix LEANER and not richer.

[@FreakMoPed8]

omg, did i really mix it up?!? HOLY SHIT! uuu thats really BAD and embarrassing, LOL thx stonecut for that tip. f*** so its also wrong in the short video, shit happens... will add a comment. thx again!

[@FreakMoPed8]

replaced the extra video and included a infocard in the pnp tuning guide. thx mate for the info!

[@bertiedoonerwind8061]

@@FreakMoPed8 wondered why my T5 just Chernobyld!

[@xterrared1]

The fuel filter cap rubbing against the carburetor case is a great tip! Thanks for making these videos!

[@FreakMoPed8]

:) u are welcome! its the biggest mistake piaggio produced, annoying so much People around the world and nearlly no one even pro workshops is Aware of it. watch here the extra Video: kzbin.info/www/bejne/bZ-le6NrhsyheLM

[@owengune]

Great video, helped a lot.

[@bertiedoonerwind8061]

Great video!!!! 2:43 Is that the 2.5mm drill bit widening the main jet hole? 7:01 is the arm/lever on remaining oil pump cut down? 11:03 image of top of modified piston. It appears to have some minor abrasions/figures on the top? Is that all? 14:04 you say but no OGM? what is the OGM? The smoothing of the ports in the cylinder and piston,( what do you use as your guide for specific enlargements?) is that similar to the work that the worb 5 guys would have done to the Malossi 172 cylinder and piston to make it perform to a higher level? It would be great to see your interpretation on a Malossi 172 kit.? I could send you one to do? ;)

[@FreakMoPed8]

yes / no / duno, need to check / OMG = "bgm" and is also sold by sip. / the t5 172 malossi does need some love yes.

[@bertiedoonerwind8061]

@@FreakMoPed8 thanks mista, would the porting and smoothing of the pistion on the 172 malossi be the same also.

[@FreakMoPed8]

11:03 image of top of modified piston: thats my FMP signature ;)

[@papanicc88]

any tuning recomendations for 177DR kit with polini box? thanks in advance and greetings from greece!!!

[@FreakMoPed8]

exchanging against vmc 177 superG

[@esencia78]

If I have matched 24 mm carburator and casing and I would like to reinstall a 20 mm carb, what could It occur then?

[@FreakMoPed8]

no problem

[@adwinoraeshad7091]

what is the purpose of removing the walls on the air filter?

[@FreakMoPed8]

more air flow. the less an engine can breath the less power he will generate.

[@FreakMoPed8]

+adwino raeshad more air for the engine.

[@LW91]

Remember, if you remove anything matching cylinder and case, is not p&p anymore.

[@FreakMoPed8]

definitions are dynamic, for me pnp is NOT opening the engine, just exchanging parts from the outside, some small adjustments dont change the basic just external work. call it "pnp advanved" or "pnp FMP style" 🙃 i can not mount ie a 24mm carb onto a 20mm casing hole, thats just wrong. It would be doing things without love (and thinking) thats why i of course adjust these things on hand which are easy solvable

[@LW91]

@@FreakMoPed8 as you say in the words "plug and play" , it will consider something that you take and mount on the engine. And most important of all, if you want to come back to the original form you can do. Try to do the same thing with modified case, I don't think it will work. Anyway I'm just saying this only because the word p&p is wrongly used. The work you did it's very good, keep going.

[@FreakMoPed8]

thx! maybe wrong in your definition, not in mine. it still fits cause the engine stays closed no need to have the same opinion here. "pnp advanved" ;) no worries, original 200cc cylinder ALWAYS works, why? simply cause it only has 1 real port, the other 2 are closed fake ports = they dont care if the case is not adjusted cause they are closed anyways AND simply think the other way round: when pnp without case modifying is possible, why should replugging the original cylinder not work? its also just simply pnp tuning same with 177, even when the case is adjusted an original cylinder will always works its a tractor engine.

[@LW91]

So is worth If I want to put a 177 polini without matching the cylinder with the case ? I know that the power it's a lot less. 60% for the p&p without porting

[@FreakMoPed8]

always port, even when its just pnp ;) ;) no polini 177 is in general not worth the money. loveless update as with the 210 with the still same old weaknesses for decades. pnp not much more power thatn a cheap DR 177. i would take a vmc 177 for pnp

[@nikolastonic96]

Where can i contact you to get some tips for my engine ? :)

[@nikolastonic96]

Yep now i know one of my problems the rotary pad is f***** mesaured it at 0.1 probably its even worse.

[@FreakMoPed8]

go2my Facebook page ie: de-de.facebook.com/freakmoped

[@FreakMoPed8]

try the rv trick while Assembling it. 0.1 should be okis, but with si carb u already see and feel the effects

[@seansimpson2586]

can you shave fins off malossi 166 to keep auto start?

[@FreakMoPed8]

Yes u can

[@inspetorgambiarra]

Hello, I live in Brazil, I have a 200cc wasp that only has one admission window, is it possible to rework this cylinder with two more windows? Do you know of any tutorial on youtube that can open more windows in the cylinder? I anticipate my thanks.

[@FreakMoPed8]

kzbin.info/www/bejne/goS3Z6ylnKite9U

[@inspetorgambiarra]

thank you mista.

[@rclavier]

hello.. what did you suggest for polini 177, as clutch cog and primary cog? thx

[@FreakMoPed8]

hy romuald. pnp runs fine with 68/23 and further tuning (timings of cyl and inlet Timings of crank 75°) the 65/23 is a musthave! everything else is too short and throttles the engine really bad.

[@rclavier]

hello!! thanks for your answer.. my cases are untouched, just polini 177 21/65 si24 and bigbox sport.. i just want to imagine if 21/65 is the only good thing? you make great job!!

[@FreakMoPed8]

so weired, i only see ur 2nd comment on Google as an alert but not on KZbin... and the button answer doesnt work... grrr so its a plug and play polini 177, then u take 22 or 23 cogwheel for the original 68 Primary. only 21 is too short, u loose Performance with that. the bbS is the totally wrong exhaust for your setup sorry to tell u that. bbS need proper inlet- and cylindertimings (75° crank and even 10° overlapping, and 120/176 cyl) to work well, otherwise it performs worse than a siproad, bbt or polinibox, These 3 are the right exhausts for your setup as u only have 45° inlet timing with the original crank, no adjusted side ports in the case, and Timings below 170° with the original 177 kit. get a polinibox! :) "romuald clavierhello!! thanks for your answer.. my cases are untouched, just polini 177 21/65 si24 and bigbox sport.. i just want to imagine if 21/65 is the only good thing? you make great job!!"

[@rclavier]

ok thanks, what do you mean by "polinibox"!!

[@rclavier]

which kind of dremel do you use?

[@robertofernandez5310]

exelente explicasion

[@adesunarya5557]

Please translate in indonesian

[@FreakMoPed8]

quite difficult as i dont speak indonesian ;) guess english is international and fine.

[@adesunarya5557]

@@FreakMoPed8 I can not speak english

[@bertiedoonerwind8061]

@@adesunarya5557 www.google.com/search?q=google+translate+indonesia+english&rlz=1C1GCEA_enNZ861NZ865&oq=google+translate+indon&aqs=chrome.0.0j69i57j0l6.8779j0j8&sourceid=chrome&ie=UTF-8