Miura CB 1008 golf club repair and Adams Pro golf club assembly

  Рет қаралды 7,614

McGolf Custom Clubs

McGolf Custom Clubs

Күн бұрын

Пікірлер
@td1138
@td1138 6 жыл бұрын
You are definitely a “Ferrule freak”, but that’s one of the reasons your build quality is so good. Forced me to ask myself with each club I build, “Is this McGolf-quality ferrule work?”. Thanks for making me better!
@kalyanrouthu
@kalyanrouthu 6 жыл бұрын
Really like the 4k video
@station2station544
@station2station544 5 жыл бұрын
From someone like myself who plays +1/2" over, those are some heavier than standard heads. I do my own building (and have for 15 years) and when I see a 6 iron weigh 263, I cringe knowing that I'm going to be fighting swingweight on my Modus 120 shafts.. I love when the 6 iron is 259'ish and 7g increments. In your experience are most Miura heads on the heavier side. I typically see American brand 6 irons living around 260/261. Thanks. Great video and thumbs up given.
@McGolf
@McGolf 5 жыл бұрын
I'm used to starting at the 5 iron for weights and typically I see 253 to 256 in weights. Doing 7 gram increments that would make the 6 iron 260 - 263g. That is typical for a set here. I believe Miura does that same. However you couls ask for lighter heads. They are very specific in their manufacturing.
@TTT-Turbo
@TTT-Turbo 2 жыл бұрын
Hi, how did you clean the heads, I have the same set and couid do with a wee ckean! Thanks Ian
@cwugrad396
@cwugrad396 5 жыл бұрын
That was so interesting. Great stuff
@kalyanrouthu
@kalyanrouthu 6 жыл бұрын
I can watch these videos all day. What was the shaft length on the hybrids? Thanks!
@McGolf
@McGolf 6 жыл бұрын
Kalyan Routhu to golfer requested 39.5 , 39, 38.5
@ccreel7474
@ccreel7474 2 жыл бұрын
which shaft will be the most similar to the Alta cb iron shaft regular flex graphite?
@McGolf
@McGolf 2 жыл бұрын
Look for anything counter balanced, although that will prove to be difficult. Id look to aldila or ust
@lukasrichter9708
@lukasrichter9708 6 жыл бұрын
Great video! I'm so if you want a bit softer of a flex (1/3) you put an 8 in a 9 and cut it down?
@McGolf
@McGolf 6 жыл бұрын
yes
@jteddy11
@jteddy11 6 жыл бұрын
Another great video, builder question I was cleaning out a hosel on a ping taper tip. Drill bit must have been low quality or cracked, didn't know but tip of drill bit broke off down (3/16's or so) down in the hostel. I tried some heat and Kroil but can't grip it to get jammed bit out. Everything I touch breaks, lol. Any suggestions to get it out thanks
@McGolf
@McGolf 6 жыл бұрын
jteddy11 you might try an easy out. Drill a smaller hole in the drill bit then use the easy out to back it out.
@jteddy11
@jteddy11 6 жыл бұрын
Damn auto correct, hosel I want to type. McGolf thanks for the reply will give it a shot.
@mikeb1149
@mikeb1149 6 жыл бұрын
I'd be interested in your feedback on those Adams hybrid heads. I bought the 2H,3H,and4H heads in the spring and had a local club builder put them on some UST Mamiya SmacWrap shafts. I felt this would be a great combination for distance and feel. When I took them to the range all I did was hook them horribly. As a right hander my miss with hybrids in basically a snap hook. When I set the clubs down in the address position however they look extremely closed. I usually have my grips as logo up, so they can be an alignment cue for my club face. The grips seem correct, but the face just points dead left for my eye. Is it possible the club builder was that asleep at the wheel and misaligned the heads that badly or are the heads built 'closed'? Thanks!
@McGolf
@McGolf 6 жыл бұрын
I would set the club on the ground without looking at the grip and see if it looks closed. If not then realigning the grip may be needed. Again if it does NOT look closed, grab the grip and take a swing. then you will know
@jasjar72
@jasjar72 6 жыл бұрын
Did the customer request all of these specs? How did he know what to ask for? Did you assist him in any of the choices of shaft, flex, length, etc?
@McGolf
@McGolf 6 жыл бұрын
Jason Jarrett the customer asked for the specs. I am assuming he knew the spec as they were specific parameters. I did however question the hybrid spec. After a quick phone call all was smoothed out
@allenwilson8913
@allenwilson8913 6 жыл бұрын
How many sets of irons could you build in a day? Assuming you didn't have any interruptions or big problems with the clubs and worked a normal day....
@McGolf
@McGolf 6 жыл бұрын
Allen Wilson my personal best is 4 full sets that including frequency, lofts and lies etc. it takes two day due to waiting on the epoxy to dry
@Otis790
@Otis790 6 жыл бұрын
How many of those honing( hosel ) brushes do you go thru a week ? Is Golfworks your source ?
@McGolf
@McGolf 6 жыл бұрын
Bean Alampi about one set every six month and yes Golfworks
@tnfbfan76
@tnfbfan76 6 жыл бұрын
How do you frequency match Nippon shafts? Do they not come pre cut?
@McGolf
@McGolf 6 жыл бұрын
Henry Frankenberg they do but the .370 shafts are long and can be done
@mattrevilock2038
@mattrevilock2038 6 жыл бұрын
I love these post. Awesome. Did you get to play in Scotland?
@McGolf
@McGolf 6 жыл бұрын
Matt Revilock two rounds until a blew out my knee changing out rain gear arggggggg. Going to docs tomorrow
@jamesbosuego
@jamesbosuego 6 жыл бұрын
What are the specs for the ferrules you used?
@jamesbosuego
@jamesbosuego 6 жыл бұрын
oh and did you find the flow/spine?
@McGolf
@McGolf 6 жыл бұрын
Jason Bourne 3/4” .370
@McGolf
@McGolf 6 жыл бұрын
Jason Bourne yes I did
@tnfbfan76
@tnfbfan76 6 жыл бұрын
what was the hosel size on those CB1008?
@McGolf
@McGolf 6 жыл бұрын
Henry Frankenberg they come in .355 and are usually bored to .370
How to Build a Golf Club - ferrule and epoxy
24:12
McGolf Custom Clubs
Рет қаралды 11 М.
Adam Scott Visits the Miura Factory
12:49
Miura Golf
Рет қаралды 726 М.
How to have fun with a child 🤣 Food wrap frame! #shorts
0:21
BadaBOOM!
Рет қаралды 17 МЛН
요즘유행 찍는법
0:34
오마이비키 OMV
Рет қаралды 12 МЛН
She wanted to set me up #shorts by Tsuriki Show
0:56
Tsuriki Show
Рет қаралды 8 МЛН
$1 vs $500,000 Plane Ticket!
12:20
MrBeast
Рет қаралды 122 МЛН
Do you need new irons?
24:45
McGolf Custom Clubs
Рет қаралды 22 М.
I BOUGHT MY FIRST SET OF MIURA GOLF CLUBS...
16:10
SAS Golf
Рет қаралды 56 М.
I got sent Adam Scott's ULTRA RARE Miura Irons!
15:23
Rick Shiels Golf
Рет қаралды 382 М.
Ian's WITB 2020 // Detailed Look at All 14 Clubs
24:12
Club Champion
Рет қаралды 175 М.
Building precision machines is simple, until it isn't.
39:53
Not An Engineer
Рет қаралды 303 М.
How to Polish and Plate a Golf Club - 2004 Mizuno MP-32
7:10
Brad Meehan
Рет қаралды 117 М.
How to have fun with a child 🤣 Food wrap frame! #shorts
0:21
BadaBOOM!
Рет қаралды 17 МЛН