Most Affordable 3 INCH Lift Kit for Jeep Wrangler DIY INSTALL and review | MotoFab Lift

www.Garagecouple.com
We finally did it! We lifted our Jeep Wrangler JKU 3 inches, and we could not be happier with the way the Motofab kit went in, as well as the new ground clearance for not much coin! We love it! We hope you enjoy this step by step DIY install guide. As you have seen, not all installs go smoothly, but this was the gold standard. Everything dropped right into place. Having done this once, we could do it again in under 3 hours for all 4 corners. Pretty awesome. Anyways, here are some links as promised: Jeep drives like Original, which was huge for us. Don't forget to enter our headlight giveaway! Cheers!
Motofab 3 inch lift kit - amzn.to/32bSdE9
Motofab 2.5 inch lift kit - amzn.to/2VD1S4e
Mechanics tool kit - amzn.to/33rdlGU
Spring compressors - amzn.to/2OIcn4W
Liquid wrench - amzn.to/314XEn2
3.5 ton floor jack - amzn.to/2VAdMvP
3 ton jack stands - amzn.to/2M9pEl9

[@Garagecouple]

Support our channel by checking out some of our awesome and recommended JK mods, all links are here: Bright LED headlights - amzn.to/2JR4fNP Smoked LED turn signal - amzn.to/2EQ7X67 Steel Stinger Front bumper - amzn.to/2WjykMA LED tail lights - amzn.to/2JPBL7f Under seat subwoofer - amzn.to/2JOKDK4 Red metal handles - amzn.to/2Wik8U1 Red shifter bezel - amzn.to/2HRZscH JK light bar - amzn.to/2EPEOYH Rock lights - amzn.to/2JPBUHP A piller switch pod - amzn.to/2MoWBw2 Door hinge side step - amzn.to/2ENee2A Trunk mounted table - amzn.to/2EOywbL Door hinge side mirror - amzn.to/31pQs5a

[@nautica1017]

I have been thinking of getting this, but after watching your installation video and then the review of 1 year later, I was sold. Love the channel you guys explain everything very understandable.

[@Garagecouple]

Appreciate your support! Howd yours turn out?

[@lalp01]

After a few months of getting the kit, and after an engine and transmission breakdown that required both to be changed, I finally installed the kit, following your advise. Worked like a charm. Took me about 6 hours to do the whole thing alone in my garage. I love it. Keep up the great videos. Cheers!!

[@Garagecouple]

Glad to hear!

[@lalp01]

@@Garagecouple So, I hear that you are a physician. So am I. I am a hand surgeon in Florida, Wesley Chapel, north of Tampa bay. I love doing things to my cars. My Jeep is my baby. Love your channel.

[@Garagecouple]

That's cool! I'm an Anesthesiologist.. sharing that same feeling about the jeeps as you! Cheers 🍻

[@appathejku5848]

For $130 it's a very good lift. My crew and I all run it currently and it's done all of us very well so far.

[@Garagecouple]

Awesome! I am glad to hear you like it. It's a solid entry level lift!

[@Garagecouple]

We're in southern California!

[@shawnyoung3033]

I just had this put on my 17 jk sport. I love it. Did you have to get alignment?

[@starkiller6740]

How much labor cost u think it would be

[@SZeeshanNaqvi]

Can you run 37's with this kit?

[@spartanCody08]

Great video! Really helps to see the scale of work it takes to put a lift onto a jeep. The voice over explaining what's going on was helpful as well!

[@Garagecouple]

Thank you for the comment! Let me know if you have any questions! Cheers 🍻

[@aggrex]

Great DIY budget lift video showing a few safety tips like jack stands, tire under the jeep and spring compressor tip etc (except for foot protection). Next look for some sway bar quick disconnects...makes disconnecting super simple when going off-road.

[@Garagecouple]

Awesome! Thank you for the comment! Will do, again thank you! 🍻

[@nicolasprice9860]

i would definitely be watching the cv boot on front drive shaft!!! common failure with any lift on jks. rzeppa high angle cv joint is good fix.

[@Garagecouple]

Thank you for the tip!

[@fixmeuphandyman]

@@Garagecouple yup, i had it happen with my 2.5' teraflex lift and 35" tires. Def a common issue, once you go up an inch or two in lift kits, that CV boot will give and the bearings in the front drive shaft will start to make cracking and popping noises because the OEM shaft isn't designed to run daily in that angle. Best thing is to get new drive shafts with yokes on each end and ditch the OEM CV setup. Curious to see how the spacer kit will work. It adds more bolt tie-in's which I myself am weary of bc it creates more points of stress and failure. Hopefully you guys don't experience that.

[@markmissildine961]

@@fixmeuphandyman hey what the fix for the CV boats and do you have a link to the drive shaft or is it going to have to be made custom

[@fixmeuphandyman]

@@markmissildine961 you will have to take a measurement of the driveshaft length after putting on the lift and have someone make you one. It can be done with or without the existing driveshaft in if the height of the lift allows. My fix for the moment was getting another OEM driveshaft from someone who had one in their garage until I can afford to have one made and ditch the CV joints and go with something a bit more robust.

[@adventure_48]

@@markmissildine961 This is Kevin, if you want to see my Jeep, head over to The Texas Exit page and check it out. I haven't done a full walk around but you'll be able to see a little bit of it.

[@daubie3]

Hey Guys, Great video. Just a little hint/tip, any time you are changing things with the suspension, it is much much easier if you loosen the control arm bolts and remove 1 bolt from the track bar. that will allow your axle to be much more flexable and give you more travel without fighting against you. The arms and track bar are holding the axles in place when they are tight. Besides, you should always loosen the control arms and then re tighten them back up after it is back on the ground with tires so they are not in a bind from the old ride height before the lift. Make sense? Keep up the good work... I still think Jerry was going to pick me.... :-)

[@Garagecouple]

Thank you so much for that pro tip. I will make a note of it and do that next time we do anything suspension for the rigs. I appreciate you taking the time to add that... Lol, Jerry was being a brat..if he was more into it he would have forsure grabbed your paper..Oh well, hopefully next time! Thanks so much for watching!

[@daubie3]

@@Garagecouple Well, I'm no pro by any means, but I have been wrenching on Jeeps and the like for a little over 40 years now and I have learned a few things along the way by busting knuckles and smashing fingers... So, that was WAY before this thing called the internet. Early on you just took your best guess at how to do something and try it until you got it done, and then hope you remember how you did it. (To help reduce blood loss the next time) But, like i had said earlier, it would still be a good idea to loosen and then re torque all of your control arms with the Jeep sitting on its wheels. That will relax the bushings and take the preload out of them from adding the spring spacers. Again, you guys keep up the good work. In case you were wondering I presently have a 2005 TJ RUBICON. I've had a couple of JKU RUBICONS, but really keep going back to the TJ's...

[@a13xsalinas7]

You guys are amazing very entertaining and keeps me wanting to upgrade my JKU

[@Garagecouple]

Appreciate the kind words! Right on!

[@Sami-rp7mf]

That was great. Not a mechanic or a great handyman so learned quite a bit. But. I'll have to to do this outside. Thanks

[@T3m0ur]

I subbed as soon as you mentioned affordable mods! Who doesn’t love great beginner mods on their Jeep!! Can’t wait to get one :(

[@Garagecouple]

Awesome! Thank you!

[@GF-pc5bt]

All I saw from this to this was a wardrobe change!!!

[@Garagecouple]

Lol!

[@jallwine]

Thank you so much for this video. I was EXTREMELY helpful!

[@Garagecouple]

Stay tuned for the follow up video, premieres tomorrow at 2pm Pacific

[@wykkydjvc]

didnt bother watching cuz you got the longest sponsor vid i ever seen holy crap

[@Garagecouple]

Oh okay bud

[@TonyArechiga]

Installating this kit and the brake line stuff made me nervous. Ha! Felt like I was going to break it. Ha! (Pun intended)

[@vanislandfishing4159]

The nut that wouldn’t go on was a stover nut it’s ment to go on and stay on

[@Garagecouple]

Thank you!

[@TonyArechiga]

Had the exact same problem with the supplied nut. It wouldn't go on with any tool.

[@luigarci5202]

Gracias a este video también levanté mi Jeep aunque yo use Rought country 2.5 me ayudó mucho este video

[@Garagecouple]

cheers

[@luigarci5202]

Saludos desde Austin Texas

[@luigarci5202]

@@Garagecouple Right now go to suscribe

[@terryderush7066]

What a man will do to keep a Beautiful Woman HAPPY!!!! Great job.

[@Garagecouple]

Thank you so much!

[@doctordeath5519]

Stright forward lift. Good job !

[@anthonycalderon3569]

Looks good guys 👌🏽 Recommend to buy new links for the sway bar and some extended bump stops

[@Garagecouple]

Solid advice, will likely do that soon! Thanks for the tip and thanks for the comment! 🍻

[@L319DNHUSA]

FYI. If you would have unbolted shocks and sway bar links on both sides let suspension hang install springs on both sides before re assembling anything. It would be much easier to do your coil spring spacers

[@Garagecouple]

Thank you !

[@jasonfiveash005]

Yikes! Only one spring compressor? Good thing it wasn’t tightened much or it could shoot out at you! Always use two.

[@Garagecouple]

Totally!

[@williamsmyth8703]

My headlights are completely shot would definitely like a new set

[@mcplar1971]

Great video.. bought the RC version which is pretty much identical and will be installing it this week. Word of caution, I noticed the speed sensor wire was the issue with the first rear corner. Careful not to snap that, another hundred bucks to replace. Disconnect the wire at the frame and it should give you plenty of room. Glad to hear you're still happy with this lift!

[@Garagecouple]

I'm glad to hear you love your kit too! Thank you for the suggestion! All the best!

[@johnortlip1140]

"And it's in". That's what she said. "Just tug on it; it will work" y tambien

[@Garagecouple]

Lololol

[@johncourtneyscott2757]

It looks great guys

[@Garagecouple]

Thank you!

[@BadInfluence_JKU]

How has the lift been since install? Would like to see an update video

[@Garagecouple]

We are planning on making one soon! Its been great

[@BluePen-AZF]

@Garagecouple this was 4 yrs ago.. How did the factory shocks hold up with using the spacers? Did you end up going for lift shocks or keep going as you did?? How was the road travel??

[@Garagecouple]

Still on the same set up rides absolutely amazing

[@BluePen-AZF]

@@Garagecouple Thanks for the feedback!! And congrats again with the Baby!!!

[@4LowConcepts]

Awesome video guys!!

[@Garagecouple]

Thank you so much!

[@michelskelling]

Wow! I need that. And it look so easy.....

[@Garagecouple]

Was very straight forward! Let me know if you have any questions! 🍻 🚙

[@caponyx]

just bought a JKU and im wondering what lift kit youre using. love the channel Ive got crazy mod bug so thanks for the links to the products

[@Garagecouple]

Hi there! Welcome to our channel 👋! We are using the motofab lift. The link is in the description 👍

[@paulnnateproductions]

Ok the only error I see was that the "biggest bolt " is actually for the rear spacer. The bolts are very close. Your rear spacers welded nut is upside down. Otherwise helpful

[@ReverseTurnstyle]

How is this lift holding up? Any need for a longer drive shaft?

[@Garagecouple]

Hi there! Lift has been completely issue free. Literally couldn't be happier!

[@richweber5090]

@@Garagecouple did you need to get an alignment after? do you use an adjustable track bar? Basically was it just 'plug and play'? Great video!! ~R.

[@randellwagner3454]

Thanks for video an chance to win those headlights..

[@Garagecouple]

Be sure to check out ourblatest video for another chance!

[@williamrunsatlanta9491]

Hey I know I’m late but are you still giving away those LED headlights?

[@riderkonkle9972]

Great vid!!Just curious if you had any kind of lift on the Jeep before putting on the spacer lift kit? or if you just ran the 35's on a stock suspension/lift. Thanks in advance!!

[@Garagecouple]

Thanks for the kkind words! We didn't have any lift, we were running stock height with 35s without any rubbing or issues, but we had to cut the fenders! loving the lift kit! Cheers

[@starkiller6740]

Can u stack this if u have 2in lift kit

[@nelsonenaccion4x424]

Great video guys i just buy an Rubicon 11 is original so that is my begin lift i would like to do it looks great guys question did you have an video how you cut the fenders flares thanks ill ready suscribe

[@Garagecouple]

Hi there! Thank you for the support! Yes we have a video, check it out on our channel! Cheers

[@sl15026]

Have you had to change the drag link or track bar after this? Any wobble?

[@2000wrx]

How did you address the driveshaft being much closer to the exhaust. Most lifts will need exhaust hanger extensions.

[@Garagecouple]

We didn't have that issue!

[@kenvetter3603]

Hi guys, great job! Did you end up getting an alignment after lifting?

[@Garagecouple]

Thanks for the kind words! We aligned ourselves and made a video on it! Just search align on our channel

[@christianaguila8297]

Aweosme video, but I’m curious because when I see other body lift kits the rear bumper stay in the same place and the car goes up?

[@donnstambaugh1506]

Love the concept of your channel, great job.,.

[@Garagecouple]

Love this

[@AI5KP]

Could you do both sides at one time to make the spring change easier? Or are you using the intact side to hold it together?

[@Garagecouple]

You totally van!

[@scottdworakoski5824]

Thanks for a GREAT Video! BTW, you two are really cute together!

[@julie_society]

When giving instructions lower the music.

[@Garagecouple]

Thank you

[@youngmoneyoutdoors841]

Well done. Not an easy project without a lift. Great video!

[@Garagecouple]

Cheers and thank you!

[@staceycampbell3640]

We have this kit and thank you for your video! Just a question we have two small 1 1/2 spacers that we can’t figure out where they go.

[@Garagecouple]

Hmm.. I'm not exactly sure where they go either..

[@Isteveym]

If they are H shaped , with tubes at the end perhaps they might be the shock extenders ?

[@G-I-JOE]

Look at 10:14 in the video. It is the spacers that go into the lower shock mount on the front axle. There is also a good shot of the spacer at 10:50 and 13:37. It keeps the bolt from collapsing the lower mount when you install the shock extension.

[@kyleb.7870]

Most affordable lift kit n spacers for a 2020 jl unlimited sport

[@Garagecouple]

Link in our bio!

[@BlazingChicknMan]

Hey guys where did you put your jack stands in the rear for the rear installation. I am having a hard time finding a place that is even on both sides so i can let down the weight of the jeep to lower the axels with the jack. I was trying to see where you had it mounted on the video. Thanks in advance! Love the channel!

[@Garagecouple]

On the control arm mounts! Good luck and let us know!

[@BlazingChicknMan]

@@Garagecouple I was able to install the 2.5 lift on mine thanks to your video. Thanks for replying

[@Garagecouple]

Oh thats awesome! How do you like it??

[@BlazingChicknMan]

@@Garagecouple so far so good. Nice to have it leveled out. That coupled with Rubicon shocks gave me a nice lift

[@hugoavalos6402]

Can i do 2.5 lift kit on 35s . Great videos very useful

[@Garagecouple]

With cut fenders yes!

[@g.w.stegall]

Where can I find the third brake light that goes behind the spare tire that’s fully functional turn signals and brake light

[@Garagecouple]

I havent heard of that before

[@josephvitale321]

You mentioned that you have Rubicon shocks... can I put that on my Wrangler Sport Unlimited?

[@Garagecouple]

Yup! We put rubicon shocks on both our tj and our jk. It takes modifications to fit a tj but bolts right up to the jk. The shocks are amazing

[@soccergolf413]

With adding this kit, did you guys have to change the front driveshaft? Or was there no real change in driveshaft geometry? Was there anything you guys had to change afterward that you didn't realize at the time of install? Thanks, this video and all your others are very informative!

[@Garagecouple]

Hi! We haven't changed a thing! Been running it this way without any issues

[@miguelfloriano9039]

Go back to that :)

[@Garagecouple]

🍺

[@kevinyin209]

Awesome video! Does this 3 in lift mess up your steering and alignment?

[@Garagecouple]

Hasn't messed anything up in the few years and 30k+ miles we have had it on

[@jacklee5071]

Installed on my 2018 JKU. Had to re-center steering wheel slightly. Left front wheel needed slight alignment. Also had to replace the rear track bar with an adjustable one to re-center the body to axel. When installing my new longer rear sway bars, I had to move them to the inside of the mounting brackets to avoid top bolt contact with the wheel. Note: JT gladiator rear sway bars are also mounted on the inside of the brackets.

[@kevinyin209]

Should I purchase a Rough Country Rear Track Bar Bracket, a front track bar bracket, and 2 sets of Rubicon Express RE1157 sway bars, 1set for front, 1set for rear? I have read a lot of reviews that an alignment is highly recommend. What about steering geometry? Does steering needed to be adjusted? Sorry, I'm new to the jeep culture. Just got a lot questions and want to make sure that's all! 😅

[@savethecivic96]

Quick question what size wheel spacers are you guys running? They look beefy.

[@Pnwutvadventures]

Hey guys just wondering how has this 3in lift held up? I purchased a 3in fab tech lift kit with coil springs new shocks front sway bars and rear trac bar relocation but now I’m having people telling me I will need a driveshaft control arms and trac bars just wondering how yours handled after this lift kit?

[@GhostshooterGames]

I have 33x12.5R20 tires. The front of my truck measures 43 inches. How much would it be lifted?

[@altonwilliams4654]

Ight you guys talked me into it.

[@dustinramsey358]

Question: I just installed synergy front end parts… New track bar, new tie Rod, new stabilizer, and new drag link that mounts to the top of the passenger side tire top knuckle(flip over kit). Also installed track bar relocation bracket that now matches the same elevation mount point of this new drag link flip mount. I currently have 2” lift on the jeep, but now the top part of the track bar relocation bracket is hitting the bottom of the jeeps frame when I hit a bad pot hole or bump. Will this 3” lift kit from Amazon solve my issue by providing more clearance, or 4” lift??

[@Garagecouple]

That's a good question. I'm not sure. If you have a clearance issue then yes. You would have to measure how much more clearance you need and buy the appropriate kit.

[@rlawrence2]

"the supplied nut" was a lock nut; that's why you couldn't put it on by hand man.....

[@Garagecouple]

Lot has changed since we made this video

[@natewelch6608]

My 2008 jeep wrangler has the smallest looking springs. Did you guys change out those at some point as well? or just put the 3" spacers on it?

[@Garagecouple]

We put in the rubicon springs and added the spacers, but we are completely re-doing the suspension soon, stay tuned

[@MattBrownbill]

Great vid, thanks 😁

[@Garagecouple]

You are very welcome! Thank you for watching!

[@kellianderson2582]

Did you use the factory sway bar links when u installed the lift kit or did you have to install longer sway bar links I have a 2015 jku I ordered this kit just wondering before I get started

[@Aamilahpeso]

Do you have any recommendations for a 2021 Willy’s lift..this won’t fit my jeep

[@fieldsbazen543]

Have you had any problems with this lift kit? I’m thinking about putting this on my 2011 jku. Thank you guys!

[@Garagecouple]

No problems at all! Been a long time and 0 issues

[@fieldsbazen543]

Garage Couple thank you!

[@vanessafrmtx1687]

Would you suggest brake line extensions or were you comfortable with how taught they were

[@Garagecouple]

We were happy with the brackets that came with this kit. So far has been working really well for us

[@juliansandoval1204]

Would I be able to use the stock springs with this lift kit, or should I buy different ones?

[@Garagecouple]

You could use the stock springs!

[@MT-lv7xn]

Awesome video... do you not need new control arms with this kit?

[@Garagecouple]

Nope!

[@stephanieball7521]

I keep getting told not to put a cheap lift kit on my jeep. Are the cheap ones as good as the 1k ones?

[@matthewgribble744]

I've been eyeballing this lift on Amazon, but wasn't sure of the quality. Have you guys done much off-road wheeling since you out on? How has it been?

[@Garagecouple]

Hi there 🖐️! We are very happy with the kit. We were just looking for some more ground clearance and we didn't want to spend a fortune. The jeep drives just as it did stock, which is great! We don't do heavy off roading, we take the tj when we do more involved trails. It has held up great though on sand, dirt roads, and mud all the best 😊

[@matthewgribble744]

@@Garagecouple awesome thanks for the quick reply!! I take mine on Forest service roads, dirt roads, and moderate trails, but nothing crazy. I'm definitely not rock crawling it or anything. Looks like I'll go ahead and snag the lift!

[@Garagecouple]

Yes, it sounds perfect for that!

[@chrischenusa6323]

The nut provided in the kit was a Nylon stop nut, it is a great nut and always fits tight Do not be afraid to use it! Oh, I forgot, I called Dickies, your safety shoes are on their way! LOL Tks

[@camachosrusticwoodwork5653]

Nice video, how's driving and off road any difference?

[@Garagecouple]

It drives like stock!

[@CYoung-fv4vu]

Question,,,, I have this kit installed. also have a set of JKS Quick Disconnects up front for the swaybar links. Wondering if I did disconnect the links would that front spacer stay put if it gets fully extended going offroad????? Have a trip coming in a few days

[@Garagecouple]

Not sure about that! I'd check with a professional!

[@crkaiserman1442]

Based on my knowled, really this basic Kit will impact in the geometry of your jeep. Using 3" should be required to adjust the Track Bar with a recolocation bracket or well replacing with new adjustable track bar, also is the same issue for Panhard bar. Really I think is better to do this lift work with a complete lift kit.

[@Garagecouple]

Its been driving like this perfectly fine for years

[@alyssahernandez9780]

@@Garagecouple I have to agree with about track bar as well as a few other parts are necessary to make the Jeep stable. I had this installed on my JKU and the steering was all over the place. But then I learned why. Driving it felt like the sway bar was disconnected but it wasn’t. Super scary.

[@fvkn_savage]

Just put this lift on my 2017. Still have the rake in the front but regardless i like how it came out and the height i got and clearance for the 35”s i put. Great video watched it a few times before installing mine. Thanks for the vid

[@Garagecouple]

Love thia comment! Glad we helped! Cheers

[@tonyrudd5769]

I wish you would have not sped up while placing parts from lift kit.

[@Garagecouple]

Sorry about that...

[@williamvarner3541]

I’ve heard of people having to use longer sway bar links for front and rear. Did you guys have any issue with that?

[@Garagecouple]

Nope!

[@williamvarner3541]

Awesome I bought a similar kit and was reading of people having to do so! Thanks for the info!!! Love the Jeep btw!!

[@richsmith3120]

I just hope you torqued all the bolts back to spec.

[@Garagecouple]

We did not! We just gave it some "ooomph" and 1 yr later still holding fine!

[@richsmith3120]

Consider yourself lucky so far.

[@Garagecouple]

Not really! Not lucky, things don't loosen when given oomph..hehe

[@MyTomatoesHateMe]

Did you need any additional components, like sway bar links or rear track bar bracket?

[@Garagecouple]

Nope! Just whatever you see in this video. It's been driving fine since we installed it. Still has the same lift kit

[@MyTomatoesHateMe]

@@Garagecouple Thanks for letting me know! I actually purchased this kit over the weekend and just found your video. I was wondering if I needed to order anything else. Is there no change in its handling, both highway and off road? I'm no wheeler, but I'd like to have that option

[@Garagecouple]

@@MyTomatoesHateMe drives just like stock just higher. Didn't need anything else

[@MyTomatoesHateMe]

3000 mile checkin. It's just like the factory ride. I had a bit more difficulty than your video, but it was not difficult.

[@johnbelch8919]

Awesome lift

[@Garagecouple]

Thank you!

[@Fabuliciouz18]

How big are your spacers?

[@Garagecouple]

2 inches

[@Fabuliciouz18]

With a 3 inch lift kit can you put 35 inch tires without modifying anything ?

[@baldeagle7604]

Shouldn't you be getting springs that are meant for a 3" lift? Going to be a pretty wobbly ride.

[@Garagecouple]

Its been over a year with this set up and the jeep drives like original. It drives GREAT and we couldn't be happier with it!

[@martinkolar3595]

Is yours JK or JL? Thanks

[@yeyosrepairs6634]

Good video 👍🏼

[@Garagecouple]

Thanks for the visit

[@zumezoom9593]

how much lift should i install on my jeep if i plan to install steel front and rear bumpers, with steel rock sliders and skid plates? obviously i'll also need to install a winch and carry a minimum of 35x5 inch tires?

[@Garagecouple]

How high do you want your jeep?

[@jeffw7233]

Can you share what the shop light or link to the LED light is? Thanks

[@Garagecouple]

We have them in our amazon shop, just google garage couple amazon shop

[@coreydawson5689]

Does this lift get rid of the factory rake and make the Jeep sit level?

[@Garagecouple]

Ours didn't have a rake from the factory!

[@coreydawson5689]

Garage Couple did you regear the Jeep to run 35s

[@augustusanderson6949]

Harbor what? I thought u said 😱 fright! No

[@Garagecouple]

LOL!

[@rivvercooper2410]

How is the lift working still and did you guys need to upgrade your front driveshaft

[@Garagecouple]

Lift has been perfect. No issues at all. We didn't upgrade the drives haft or anything else aside from the kit.

[@liontigar7135]

After lifkit installation,does your traction control light stays on??

[@Garagecouple]

Nope!

[@rcpartsyard3840]

you need to center the steering wheel

[@Itsaveragejoey]

What size spacer are you running? Where did you find it? Did you make a video on spacers?

[@Garagecouple]

2 inches and we havent had the chance

[@Itsaveragejoey]

Sure, where can I find a link to these or what is the brand?!

[@Itsaveragejoey]

I’m curious if it’s an Amazon type deal. Can’t find any 2 inch spacers

[@Garagecouple]

They have them on amazon, ebay, and all over :)

[@Itsaveragejoey]

Garage Couple, ah I need links. It’s hand looking for this stuff with an older phone.

[@stratdemakis1115]

Did you have the stock shocks on your jeep before and after you did this installation?

[@Garagecouple]

We had stock jk rubicon shocks

[@hummdeez]

Did this kit level the front or is there still some noticeable stock rake ?

[@Garagecouple]

It doeant change the stock setup in terms of angles. Adds 3 to the front and rear

[@hummdeez]

@@Garagecouplethanks for the reply! do u still notice the that the front angles down a bit?

[@Garagecouple]

@@hummdeez ehh not really! We are actually preparing to do a suspension lift soon! Stay tuned

[@dejanae305]

Is this stock height before??

[@probam10]

What kind of fender flares do you run

[@Garagecouple]

Metalcloak

[@jeffchoura821]

One thing you guys did wrong and I would like to say to all your subscribers the nuts that you put on the rear frame to install the rear spacer were backwards that the rear spaces should seat tightly bolted to frame lol if you don’t tighten bolts down all the way they will rattle just a FYI good luck mine works well

[@Garagecouple]

Hasn't given us any issues or noises now in over 1 year

[@dadedadesmile]

…Hello!! I wanted to ask you if the suspensions you mount are original, and if after the assembly you felt the jeep too stiff while driving… thanks for your answer!🙏🏼🙏🏼

[@w159]

Dear Lord, it was a nylock nut… it’s supposed to be like that.

[@gilbertomartinez3087]

I have 2 inches suspension in my jk I need an inch more to put tires 37 you think this works

[@Garagecouple]

Yes with cut fenders it will work