MS05c. [Siemens S120 #2] SINAMICS S120 Configuration and Commissioning via Startdrive TIA Portal

[@gelearn2362]

Thank you very much for the lesson

[@electricalautomation]

Welcome!

[@محمدالسروري-ه4ه]

goooood

[@electricalautomation]

Thanks! Enjoy

[@bartw4245]

very, very helpful:) thx

[@electricalautomation]

Glad it helped! Welcome!

[@alejandrojulian804]

So good your tutorial series, i have a question, how i know what kind of memory cp works with the CU 320-2 PN, please help me :)

[@electricalautomation]

'memory cp'? not sure what do you mean. Thanks watching!

[@derina.maleek9408]

You nailed it

[@electricalautomation]

Thanks! My friend!

[@damianhl5448]

Very nice video. I have one question. The CU320-2 PN can only be used with S7-1500 CPU if i want commission in stardrive (i'm using stardrive v17)? If i want connect to a s7-400 i need to commission the sinamics in starter?

[@vorapobautomation9760]

How can do it in TIA ?

[@electricalautomation]

If you are using S7-400, you can not use the 'TO'. You can use the position loop in the CU320, then the S7-400 just send position command.

[@vorapobautomation9760]

Is the CU320 can use in startdrive with S7-400 ?

[@alejandrojulian804]

It can works with the S7 1200 PLC too@@electricalautomation

[@shahzaib1994]

Hello I am Using 1 CU with 2 Drive of Servo. I am using telegram 1 for Both Drive & Telegram 390 for CU. I am using profibus connection with s7300. With Programming Blocks sfc14 & sfc15. With DB. I have a Problem that only One Drive is Sending & receiving Data. Both CU & Drive 2 Show No Telegram in Interconnection setting. Could you please help me

[@electricalautomation]

Have you set the telegram 1 at the drive side? Why you are using the telegram 1 (the speed control) for S120(a high end servo drive). Aslo your question is far away from this video topic, I would recommend contact Siemens support for your application, my feeling is that you are directing not quite direction for using your control devices.

[@shahzaib1994]

@@electricalautomationYes I am using Telegram 1 for both 2 Drive. But in My Program I call sfc14 & sfc15 3 Times. 1 for CU, 2 for 2nd Drive, 3 for 3rd Drive but it only read Sfc of Drive One CU & Drive 2 Register not Sending & receiving. is there any Method to Increase Profibus Cycle. I think it is Profibus Cycle Issue.

[@electricalautomation]

@@shahzaib1994 This link should be helpful support.industry.siemens.com/cs/document/8894584/micromaster-4-(mm4)-sinamics-g120-(cu240s-d-dp-dp-f-pn-pn-f)-essentials-for-profibus-and-pkw-mechanism-?dti=0&lc=en-CA

[@aminfathy216]

Thank you good one 👍.....>3

[@electricalautomation]

Thanks! I am very busy these days, the next video will be launched slightly delay, but will be.

[@bhagyodayasinghjadhav]

Very good...

[@electricalautomation]

Thank you! Cheers!

[@movies1774]

Very good Sir

[@electricalautomation]

Thanks and welcome

[@veys9655]

how to prevent when we stop and start the cpu or cut off the power of control panel to loss home position ? I want that when I set home position once, then I wanna keep it always. it doesn't matter then whether I cut off the power or cpu stop. Can you please help ?

[@electricalautomation]

Using multiple revolutions absolute encoder for your servo drive.

[@veys9655]

@@electricalautomationBut I'm already using absolute encoder ? can't I do it with Control unit?. I mean CU320 in startdrive side ?

[@devendrachowdary2333]

I am not able to connect the plc S7-1212C with the drive S120 CU310-2 Pn

[@electricalautomation]

S7-1200 (v4.x) can not use 'TO' to control S120. You can use 'GSD' method and EPOS telegram 111 to control S120.

[@ariancontrol2430]

hello thank you for useful video! i have a sinamic cu320 version 2.6.2 with CBE profinet card and i want to have it in TIA portal but there is not such model in TIA hardware catalogue!! is it possible to add this model in tia portal ? if yes how?

[@electricalautomation]

I would recommend using Starter software and ' auto config' function, you can view from kzbin.info/www/bejne/b6DHpqVjdpaSoqs

[@vorapobautomation9760]

Good Thank you

[@electricalautomation]

Welcome 😊

[@vatsalthaker2122]

Hello sir... please resume the series....

[@electricalautomation]

Thanks watching, yes, the Step3 will be launched tomorrow. I am very busy these days, sorry for releasing delay.

[@dmitrijbozhok]

Good afternoon. Does anyone have a SINAMICS Startdrive V14 SP1 S120 under TiaPortal V14 SP1?

[@electricalautomation]

support.industry.siemens.com/cs/document/109746466/sinamics-startdrive-v14?dti=0&lc=en-WW support.industry.siemens.com/cs/document/68034568/sinamics-startdrive-v14-sp1?dti=0&lc=en-DE