MUM5 Disassembly Process - Bosch Robot Multifunction Kitchen Machine

How to disassemble Bosch kitchen machine MUM5. Detaching top cover, motor unit and gear wheels. Basic repair process. Here is new video with complete disassembly and reassembly (gears replacement): • How To Repair - Gears ...
Model: MUM58250/06
Part Number: 12042424
proex.sk/produ...
www.proexservi...
www.proex.sk/
#diy #repair #kitchen #machine #assembly #disassembly #gear #replacement #bosch

[@proexservis]

Here is complete disassemble & assemble video of MUM5 +all gears replacement: kzbin.info/www/bejne/f36udYt_ib6Hb5Ysi=_pHw6qPuDrvZk9A4

[@proexservis]

…and swivel arm lock + side cover panel: kzbin.info/www/bejne/o5Cpf6KCbq1labssi=d_J1rOoBrFJGD8Ov

[@jogobew]

Thanki you! You helped me repair my MUM5 - excellent movie!

[@proexservis]

You are welcome 😎👍

[@Biela2008]

Is there a way to remove the fanwheel? (gray piece at the top of the motorshaft 4:15) Mine was stripped and I cannot get it off without risking breaking the plastic gears in the housing.

[@proexservis]

Yes, you have to hold tight rotor and unscrew that plastic gear for bottle, you can disassemble those white gears first to not damage it

[@Biela2008]

@@proexservis Hmm I wonder, if the shaft and the fanwheel are left threaded though?🤔🤔

[@proexservis]

@@Biela2008 google part number 00653825, there are pictures of this rotor without fanwheel 🫡

[@SO8ESO]

Hi, thanks for sharing the video, it's truly impressive! I encountered an issue with my Bosch MUM5 during its last use. There was a distinct burnt smell and subsequently, it stopped working. Could you please provide some insight into the problem? Do you think it is feasible to repair? Thank you!

[@proexservis]

Hi, probably carbon brushes worn out, but I would suggest to check rotor and gears inside before replacing only carbons. 👍

[@SO8ESO]

@@proexservis Thank you very much for your kind reply. Unfortunately I don't know how to check the rotor and gear. Would you please give me some hints?

[@proexservis]

First, disassemble machine, you should be able to see on carbons and rotor, then you have to unscrew torx20 screws from motor and by this you can check plastic gears and replace any damaged part

[@SO8ESO]

@@proexservis Thanks a lot, I will try.

[@jakobryden]

I need to replace my carbon brush I think. I ordered a new one and will try reassembling once the part arrives. Is there a good choice of grease for taking some precaution and lubricating the gears when I am at it? Can I just use any universal grease e.g. CRC (DIN 51502), or what do I need to consider? Thank you for this great video!

[@proexservis]

Yes, any food grease is ok, especially for white gears, they like to crack. There is never enough food grease.

[@dawidmatuszak8869]

​@@proexservis@proexservis where can you buy replacement parts for this robot? And are the brushes replaceable?

[@proexservis]

@@dawidmatuszak8869 from any BSH service (bosch siemens hausgerate) like us or directly from Bosch-Home site. Yes, brushes are replaceable.

[@HenkPoley]

Hey thanks, that looks decently easy, do you also have a video how to replace the side panel, swivel lock button and bottom plate? (e.g. to swap to a different color)

[@proexservis]

Hi, you are welcome 👍 Do you mean this swivel lock and side panel? kzbin.info/www/bejne/o5Cpf6KCbq1labssi=d_J1rOoBrFJGD8Ov

[@HenkPoley]

@@proexservis Yeah 👍, I also found all the outside coloured parts (€60 for a whole set of panels, buttons and stickers 🤔) getting disassembled here: kzbin.info/www/bejne/oJ6rgHeBZ9Fko8k

[@proexservis]

True, those are videos without preparation repairs, as it comes, so no video cuts, lot of background work during repairs (nothing happens in some parts so you need to fast forward a lot) 🙃

[@HenkPoley]

Yeah , I also found all the outside coloured parts (€60 for a whole set of panels, buttons and stickers ) getting disassembled at another of your videos: "Appliance Rescue: January POV Repairs - The MUM5 Day - 09/01/2024" (KZbin doesn't allow me to link, reject the post)

[@proexservis]

@@HenkPoley weird, i see your comment with that link 🤔 even with reply kzbin.info/www/bejne/oJ6rgHeBZ9Fko8ksi=oGqBJ5Hc1A1dZ4tk

[@MichalekEmbeEM]

Thank u very much!!!

[@proexservis]

I’m glad it helped 👍 and thank you for saving appliance from being thrown away 🔧😎

[@paweldobro]

I did as in the film and as in 2:21 I dismantled the body. But how to mount it now?

[@proexservis]

You have to put it on the body and turn clockwise, it should lock in

[@paweldobro]

@@proexservis Unfortunately, it does not lock. Maybe I'm doing something wrong, but I'm trying to reverse the process shown in the video.

[@proexservis]

@@paweldobro if you can, send me photo of both parts to mail: [e-mail]

[@jakobryden]

Unfortunately I have the same problem- there is a minimal plastic latch in the engine housing that might have broken off. It is hard to say, but perhaps it is supposed to slot into the gap in the hinge and latch on, but it’s too worn down to attach. If that is the case, it is very poor design of the latching mechanism imo, unless the screws clamp it in place once tightened, perhaps?

[@proexservis]

@@jakobryden it holds thanks to bayonet mount, then you have to add something to 2 holes from top (before you attach top cover), it should hold until you connect all cables and mount motor unit (with regulator). Then put white top cover and screws

[@obican]

Just got one of these and the whisk attachment hits the bowl towards the front of the machine. Do you think there's any way to adjust that? Feels like the head is sitting slightly too low on the hinge.

[@proexservis]

That whisk can be assembled without any problem? it cant be probably fully locked inside due to faulty top part (00622181) that should hold whisk

[@obican]

Hi, all accessories lock in place just fine.@@proexservis

[@proexservis]

@@obican then whisk have to be faulty, deformed

[@obican]

@@proexservis my guess is that the head isn't parallel to the ground but since it's a brand new thing, I think I'll just return it instead of trying to fix it. Thank you so much for all your time and effort!

[@proexservis]

@@obican oh, if it is new, someone assembled it on friday afternoon 😅 dont fix it in warranty, return it and ask for new if it is possible. You are welcome 👌

[@StOKRATzoom]

dobrý deň. dakujem za video. v kombajne sa mi rozpadlo veľké ložisko, to na 4:24 min a prasklo puzdro. prosím, povedzte mi, čo mám robiť?

[@proexservis]

Toto video možno pomôže: How To Repair - Gears Kit 12042424 - Bosch Kitchen Machine MUM54240 Robot kzbin.info/www/bejne/f36udYt_ib6Hb5Y

[@StOKRATzoom]

dá sa kúpiť len jedno veľké ložisko?@@proexservis

[@proexservis]

@@StOKRATzoom ano, 00622182

[@StOKRATzoom]

добрий день. дякую за відео. в мого комбайна розсипався великий підшипник, той що на 4:24 хв, і порвалася манжетка. підкажіть будь ласка що робити?

[@proexservis]

Try this: How To Repair - Gears Kit 12042424 - Bosch Kitchen Machine MUM54240 Robot kzbin.info/www/bejne/f36udYt_ib6Hb5Y

[@christapilsner9506]

Hallo können Sie mir zeigen wie man die Maschine Mum 5 unten öffnet? Möchte die Stromzufuhr prüfen. Vielen Dank im voraus

[@proexservis]

Hello, do you have cord winder in that MUM5? If not, then you have to open in on top, like in video and blue/brown wires on circuit board is end of the electric cable.

[@andreynt1]

Какой используешь шуроповёрт?подскажи пожалуйста мадель

[@proexservis]

Standard T20 torx bit, on Bosch GSR 12V-35, look for 12V-35 HX or FC (it is new model of mine, better, mine is 7-10 years old)

[@adiirawan9928]

Thanks you so much

[@proexservis]

You are welcome 👍

[@contagious_smile]

Do you have assembly video?

[@proexservis]

Soon it will be uploaded, one MUM5 is waiting here for parts

[@ahmetbalcioglu8196]

Hallo ich kann die abdeckung nicht öffnen :(

[@proexservis]

Welche Abdeckung? Manchmal kann es schwierig sein, aber in meinen anderen MUM5-Videos war es immer einfach kzbin.info/www/bejne/f36udYt_ib6Hb5Ysi=cGWzPmV11SMJsN34 Which cover? Sometimes could be hard but in my other MUM5 videos it was always easy

[@iblis123123]

Dzieki, przydało sie. Btw klucz Torx 20.

[@proexservis]

Yes, this MUM Torx20, but few models of MUM robot has Torx20 & Torx15, so I was not sure, I tried T15 first 🙃

[@UT.USSRMB]

Процесс неполной разборки БОШа :-) самый геморройный процесс это боковую пластину снять после нижний, что бы не поломать.

[@proexservis]

It is not that hard 👍 Here: kzbin.info/www/bejne/o5Cpf6KCbq1labssi=U9JORT0oUMuVnGx0

[@AgaJed]

Ja mikser urzywam do traćia błki ido mizleńa sera na serńik

[@timothy790110]

its fucking impossible to get that top cover off

[@proexservis]

There are just plastic latches 🥲 first try to pry up that top latch rly hard and then slide cover. Sometimes it can be stuck coz of some liquid from mixing, but almost everytime it just need to be pushed up before sliding: kzbin.info/www/bejne/f36udYt_ib6Hb5Ysi=mKT96fcLpm9FU-hR