#mx5 #miata The engine needs to come out for a few reasons, so why not show you guys how its done. enjoy Please consider helping me finish this project by visiting the link below www.buymeacoff... thank you
Пікірлер: 43
@bassbombdom7 ай бұрын
My engine went bang last night. Need to get it out and a new one in this weekend, thanks for a super informative video with no useless filler content!
@Project3807 ай бұрын
o damn, i hope you find this video useful, no useless filler to be found on this channel 😉
@bassbombdom7 ай бұрын
@Project380 new engine is in and she runs! Just a few teething problems I'm yet to overcome haha
@tedstriker7542 жыл бұрын
So glad this video is posted. I have to pull an N/A 1.6 engine to fix a leaking oil pump. I pulled it years ago leaving the gearbox in the car, but was wanting to watch a refresher video. Yours is the only one I found that doesn't remove the transmission. I'd also forgot that to pull the oil pan off I need to pull the press.plate/clutch/flywheel off. That darn oil pump uses a small thin paper gasket between it and the engine block. If it starts to leak an engine pull is mandatory to repair it. Anytime a Miata engine comes out for rebuild, that gasket should be replaced.
@Project3802 жыл бұрын
I find it the easier way to do it
@jsportgarage76652 жыл бұрын
Appreciate the help Project 380! I gotta pull out two 1999 Mazda Miata engines. It's astounding how easy it is to pull the engine in these cars.
@Project3802 жыл бұрын
Glad ive helped you out 😊
@Beardchanics4 жыл бұрын
Very useful video, we're about to pull one out of a MK2. Haven't catch up on all yet but love the build so far. Level of details in engine look, bay ect... Very nice work :)
@Project3804 жыл бұрын
thank you and good luck with the engine removal. why are you pulling the engine out ?
@aidanbeauchamp95882 жыл бұрын
Most helpful video I’ve found so far thanks for not filling your video with unrelated content
@Project3802 жыл бұрын
Glad it was helpful! i always try and be straight to the point
@richalsop4 жыл бұрын
Great video! Funny and informative! "I just pick it up...coz I'm hench 💪" 😎
@Project3804 жыл бұрын
thanks mate. cant wait for the gym to open again
@funboy666ganja2 жыл бұрын
thanks for all your videos much apperciated
@Project3802 жыл бұрын
You are very welcome😊
@DonteWilsonChrisDornerКүн бұрын
Curious. I've seen most people say that it is easier to pull the engine with the transmission. Why didn't you pull that as well?
@Project38023 сағат бұрын
ive pulled so many of these engines, in my opinion its easier to disconnect the gear box from engine. pulling the gear box means you have to drain the gearbox, fight with the PPF bolts, take your centre console out, redo everything and then align your PPF again
@evoking123452 жыл бұрын
Thank you mate good guide, nice n simple 👌 i shall sub 😎
@Project3802 жыл бұрын
Thanks for the sub!
@nolahahnshouse33893 жыл бұрын
Your video has been a God send while removing my miata engine removal..are you on Instagram bro?
@Project3802 жыл бұрын
thank you , @project_380
@billysbikes86712 жыл бұрын
Great vid just about to do this to my mk1 so doing a bit of research but a have 1 question.... are you from norfolk?
@Project3802 жыл бұрын
close to Norfolk , the accent gives it away 😏
@rufusz10 күн бұрын
Is it a must to get the starter motor out? It’s a pita on a LH car, can’t reach the bolts
@Project38010 күн бұрын
im not sure about the left hand drive one as you have got a steering shaft in the way, the bolts are not easy to get to anyways
@XIVdot3 жыл бұрын
Thanks, the only video about removing the engine without gearbox. Is it easy to install the engine back with gearbox in place?
@Project3803 жыл бұрын
Its all down to personal preference. i prefer to do it this way but i find it just as easy. if the standard coil packs are being used i take them off before removing the engine and put them on last when installing as you can smash them on the bulk head. to remove the engine and gear box together you need more room and more head height which i never have.
@Austiiizy3 жыл бұрын
@@Project380 brother, what tool did you use to get to the top gearbox bolts?
@Project3803 жыл бұрын
@@Austiiizy Just an extra long ratchet spanner, easy with coil pack out the way
@kkm98062014 Жыл бұрын
do i need to drain transmission fluid before removing bolts that connected to engine?
@Project380 Жыл бұрын
Nope as long as you keep the prop shaft in
@streetstarusa2 жыл бұрын
DUDE I NEED THAT RADIATOR SETUP
@Project3802 жыл бұрын
HAVE YOU SEEN THE MISHIMOTO SET UP I INSTALLED?
@streetstarusa2 жыл бұрын
@@Project380 just peeped the cooling upgrade video 🔥
@DrifterDavid2 жыл бұрын
Hey man, love your vid. Could ya tell me what oil relocate that is? Been looking for one to move forward instead of firewall as I've got my catch can back there.
@Project3802 жыл бұрын
from what I can remember it was just a cheep china eBay one with the correct fitting
@chevybarboza Жыл бұрын
Hey bro what size bolts are you using for the engine stand?
@Project380 Жыл бұрын
i really cant remember but i thing g19 do a bolt kit
@chevybarboza Жыл бұрын
@@Project380 appreciate it brother
@sethy5372 Жыл бұрын
How do I depressurize fuel rail?
@Project380 Жыл бұрын
check out my video on fuel filter replacement, i explain it in detail in the video, i hope it helps
@ZeoStyleAutomotive4 жыл бұрын
I have a forged 1.8 nb engine for sale that’ll handle 380 🤷♂️
@Project3804 жыл бұрын
where is the fun of putting someone elses engine in? built no bought :)