Joe, thank you very much for this video. I just got my Rode Wireless Pro and will be setting it up with my Sony ZV-E10, so this video is just perfect for my needs. Thanks for all the content you post and for sharing your gifts and talents with us.
@zer089278 ай бұрын
Yep, got the same camera! 🤘🏼
@narptАй бұрын
I know you said "just go over all these settings" but the manual piece of setting up -6db is pretty important so people should be aware of that first, before @4:29
@kylemckenna Жыл бұрын
Nice video! Just got these to work with my FX30 and your video was very insightful.
@austingnz5 ай бұрын
Hell yeah, this video came in clutch bro. Thank you!
@SusannahPerri3 ай бұрын
Thank you so much, I have been having the same problem with the audio being too low when the camera audio setting at "1." I'm going to bump mine up and that should help. I really appreciate this video!
@AnilKumar-zo2eu8 ай бұрын
Thank you so much sir for your packaged information.
@waldeckalex11 ай бұрын
Thanks my guy this was very helpful
@waltjennette4 ай бұрын
IMO I would adjust the gain on the receiver and not the Camera! Set it to 1 to make sure that you're not relying on the camera's pre-amps and you're getting the most ouf ot the mics! Setting the camera audio above 1 raises the noise floor. That's the reason they say 1 for Sony cameras.
@DanieleBuccheri2 ай бұрын
agreed!
@ginetteco Жыл бұрын
i just got my mics and needed this! great video!
@Alpha_Paranormal12 күн бұрын
Hi maybe you can help me i Have a Sony Ax53 and i cant find it on the Gain Mode what can i do?
@markstambaugh32732 ай бұрын
Great Video but wanted to know how to set the time and date. I can't find it anywhere. My recordings all have year 2000 dates.
@DanieleBuccheri2 ай бұрын
I also noticed that they were too low. I think it's better to raise the gain in the transmitter, and leave the levels in the camera as low as possible.
@johnnyweissmuller583810 ай бұрын
Dont put sonys to 1, correct is 3, there is a software limiter active on 1
@patrickfalls681910 ай бұрын
Is this stated in the manual? If not, can you drop a link to where this information is stated?
@romainissa4 ай бұрын
do you recommend to keep setting on manual instead of auto when using with FX6 ? cause I always get low volume signal...
@BrailleSounds3 ай бұрын
Super helpful thanks!
@Sir-Kay2 ай бұрын
What if I don't use mirrorless camera, what preset should I use? I record mainly on Iphone 14 pro max and my Rode Wireless Pro recordings are too damn low. firmware update is right but, when I open Filmic Pro, I can clearly see my level is set to max but, unless I swallow the mic, the monitoring maxes out around the green bar, it's not even reaching the yellow or the red. Do you have an idea what could be wrong?I've tried Merge & split, gain assist etc nothing seem to work.
@starnod11 ай бұрын
Do you have the setup for Sony 6600? What are the gain levels for the RX & TX?
@arhon8886 ай бұрын
Hi, thanks for sharing. Much appreciated. I have question, if you set your camera to 2 for example is it possible to increase the gain on the receiver until you get the levels you need in camera ie. between -12 and -3db? I am considering upgrading my Wireless Go II's to the Pros, as I am guessing the above method would be possible without introducing any white noise. With the Go II the maximum I can set the gain to is 9db (-3db max) before white noise becomes a problem and on the camera the limit is about 5.
@benjieitech Жыл бұрын
Thank you very much for the video. You already have a new subscriber. You can make a video using the settings on the iPhone.?
@Freep-m2l7 ай бұрын
Hi what if no camera preset for Nikon z8?
@MarcAltshuler Жыл бұрын
Thanks for this. My Wireless Pros seem to have a lot of noise. Have you experienced on-board regarding to be very noisy?
@johnatwar5 ай бұрын
make sure you're turning down the gain in the camera, i don't recommend to do what he does and turn that up in camera to get his levels right, that's going to introduce a lot of noise and his because the preamps in the camera. that's why they recommend to turn it down in camera, there should be dB adjustments in the rode video mic pro for this.
@MarcAltshuler5 ай бұрын
@@johnatwar thanks but I’m talking about the receiver/recorder themselves being very noisy, even at baseline and no gain.
@VeldingNl Жыл бұрын
Thank you very much! Very helpfull!
@r2junot17422 күн бұрын
🙏 v helpful ty
@MarshaeBradbury3 ай бұрын
Hi! In post I noticed that there is no sound playing in the video. It sounds like my mic isn't on. Any thoughts on how to trouble shoot that? I'm afraid to record if there won't be any sound
@SusannahPerri3 ай бұрын
Hi, maybe you already solved your issue, but did you happen to be using one of the lav mics when this happened? I had this issue when using the lav mic the first time. It turned out it wasn't screwed into the TX all the way. The way the instructions are written is misleading as they instruct you to turn the gold screw in the wrong direction. Maybe this wasn't your issue. In any case, I hope you figured it out.
@MarshaeBradbury3 ай бұрын
@@SusannahPerri Girllllll I brought mt camera and mics to church so that one of them could help me. Turns out I plussed my mic in the headphone jack not the microphone plug in😩 I’m a rookie haha!😂
@MarshaeBradbury3 ай бұрын
Thanks for your reply btw!🫶🏿
@mosiahmtz11 ай бұрын
Can these transfer the audio to my iPhone ? Is there an app for that ?