Mycology Flowhood box tek ... Does this really work?

#WillyMyco #Mycology #Tripteamfamily
In this video I make and test out a new mycology product on the market. This a mix between a flow hood and a SAB.
PLEASE SUBSCRIBE ~ SHARE ~ LIKE
~~ Support The Trip Team Family Movement & Get My Full Library ~~
patreon.com/willymyco
~~ Grab A Trip Team Shirt Or Hoodie!! ~~
teespring.com/stores/trip-team-bodega
~~ STAY CONNECTED ~~
Follow on Instagram @Willy_Myco
Follow on Snapchat @WillyMyco
Follow on Twitter @Willy_Myco
Music by D'Rok The Menace "You Kan Not Deny"

[@alpalandfriends]

I'd recommend doing an open agar plate test to test the efficacy of this system rather than just relying on the pollutant meter you have. Would make a good follow up video.

[@omma-llama7860]

So here's a tip for drilling holes in plastic. Start the hole, but just let the center cut in. Then, switch the drill to REVERSE. Then drill the hole. The drill bit will create friction, and melt the hole to a perfect circle, and there won't be jagged edges, and there is less of a chance of the hole cracking from the drill.

[@omma-llama7860]

If this to help you, send me spores lol

[@OMFGORE]

I figured that out by accident, good tip.

[@trueheartintent]

If only I knew this before. Lol thanks for the comment!

[@davidcooper2352]

I've found that heating up a socket, melts the plastic with less mess. I get that there are fumes you don't want to inhale, just do it outside

[@TangoNevada]

I also find that Blue Taping both sides of the hole help tremendously. I just drilled 2 4" holes in a tub with Blue tape on both sides without an issues. Of course I went slow. But it was an none issue.

[@AnonymousCitizen777]

note that you cannot have the uv light on while working in the box or it will damage your eyes and microbes require at least 15 minutes exposure to kill them. "Long-term exposure to even small amounts of UV radiation can increase your risk of developing a cataract or macular degeneration. UV exposure adds up over time. Long-term UV exposure can also causes tissue elevations on the surface of your eye. These are called pingueculae and pterygia. Using sunglasses faithfully when outdoors may limit these." Also, I would recommend at least a triple layer MERV 16 material.

[@TangoNevada]

Too many people do no realize this.

[@ivan3465]

I'm literally shocked with this upgrade. There is so many ways to correctly use uv lamp, this is just crazy

[@baronchatdelamort3522]

Perhaps adding a metal reflector shield so the uv is never going directly into your eyes but only down towards your workspace? To be fair I'd actually be interested to see if one could find a smaller rectangular hepa filter that could be mounted in the "back" of the box to create positive pressure that could blow out the arm holes...

[@863Monster]

@@baronchatdelamort3522 I'm catchin what you're throwin. I was thinking the same thing about a small hepa filter.

[@shaunromero9826]

PPE? Gloves and shades?

[@bigsmalls1375]

Just getting back into my studies and I love to see that you kept on posting ❤️❤️❤️ a.ways love to see your videos not only are they informative. But your vibe is just magnetic

[@christianruiz6158]

UPDATE: you don’t need the filter or extras holes, run the light 15 - 30 mins prior of working, turn off when you work

[@samjones3433]

Wait what so just a still air box with a light in it?

[@momomeshtv7318]

tips for cutting plastic, I just use a used / unwanted surgical blade (which most people in the mycology have) and put it over my kitchen flame and cut threw the plastic like butter! I don't use kitchen knifes as they then to over melt my lines. try it, it works!

[@Oseanyboy]

Hey loving your videos, just wanted to offer some constructive criticism. I've found that the intro music audio level is very disproportionate to the mic audio level, I find myself adjusting my speaker volume. Not trying to be a negative Nelly. Peace.

[@swat1229]

I've found cutting bins by heating them with a torch and a razor works well to prevent cracks. Heat until it gets clearer, then use the knife and heat in front of it. Be safe with sharp things and fire.

[@CMZneu]

Why not use a vacuum cleaner hepa filter, those are relatively cheap... also don't ever work with the UV light turned on, it will burn your skin and eyes! he should have explained that the uv should be only used to disinfect the area prior to using it, not while you are working.

[@jakem6750]

This! There are a lot of hobbies and crafts that have been using the gambit of UV lights and most have no idea how damaging they can be, especially the C wavelength. It works because it literally breaks down DNA.

[@omma-llama7860]

Just because it says HEPA doesn't mean it will work. Vac filters suck. Check the specs.

[@michaelrandall2422]

The plastic should be enough to block the UV-c rays. Granted you don't want to spend a lot of time with your hands in the box, but if you multiply time spent by 10, so 15 minutes times 10, assume 150 minutes of uv exposure. How many of you would think twice about being in sunlight for 150 minutes? Wear sunscreen if you're really worried. Or you know, long sleeves and rubber gloves. UV lights can be very dangerous if used improperly, but a few VERY simple steps make them just another tool.

[@ryanturner6920]

I think just a true "still" box is better. Why move air if you can just work in a well cleaned still air box? This seems to be a "worst of both worlds" sort of idea. I also do NOT want alot of stuff in my still box. Just more to clean. I've got a small plastic lidded box for my clean tools and an alcohol spray bottle. That's all that stays in there.

[@Perryloc]

I have noticed a trend of places offering products for sale to 'automate' different stages for insanely high peives. Especially since they are using basic products available to everyone.

[@catsmoke5518]

All you need is air blowing in the box through a hole with a hepa filter on it and escaping the box around your two arm holes. No need for all the extra stuff. The UVC light will also kill your spores and mycelium so turn it off before going to work.

[@bobblew8530]

I do that but with a clear comforter bag so it folds away in my dresser drawer

[@LuckyChucker]

It'll cause skin cancer too

[@catsmoke5518]

@@LuckyChucker I use my uvc light primarely to sterelize agar cups beffore pouring. Not good for much else...

[@dr.doodledorf426]

I would think there would be the possibility of sucking air in the wormholes with those extra holes he's got

[@mycomama4209]

UV-C doesn't kill the mycelium actually.

[@taylorsutherland2595]

Built this, I accidently used a merv 17 filter but it's too dense for the fan to push air through. I also realized immediately after building this, that the science doesn't really work out. Sterile technique in a flow hood is to keep everything 'upwind', because contams can be blown off anything upwind onto whatever is downwind. In this design, your work is constantly downwind since the air is traveling across. The original design had the right idea with the fan blowing towards you. Like others have said, open agar plates would be the best way to test in a real world scenario, a meter won't be able to accurately account for an actual working environment where your work/hand is always upwind blowing off contams and turbulating turbulent air (because it's not laminar) even more

[@ryanpongracz8051]

I did this but way bigger, with a 20*20 box fan, and a much bigger tote, and used three filters, one pre 2200 HEPA 20*20*1, and two, 2800 HEPA 20*20*1 stacked and taped so the fan is enclosed by filters, no contams fam. Uvc in box, holes for outward air on right.

[@ryanpongracz8051]

The 2800 filtrate filters are the highest grade you can buy and very hard to find

[@Trevd508]

I've had sab boxes explode on me almost melted my gloves to my hands 😆 whenever I used bleach and or aerosol disinfectant instead of alcohol I'd have smaller deformed fruits. I don't know I'm liking the side mount design. Another guy just cuts a hole for a lam filter & epoxied it directly to a tote & strapped a variable fan to the side of the tote. I like this better because the box acts as a shield

[@chrishayes4023]

At about 45 seconds in you say you did not order thus and try it for fear if messing someone's business up. So my question is are you here to help us learn or keep the shoddy big businesses in business? And how do you know yours is just as good if not better if you've not tried thus products?

[@elotherios9524]

@@rumi108 for real

[@TOPskunkfisher]

Man killer idea sir I was wandering down this path in my head, then found this video so stoked that the concept does work quite well, was wondering if having this setup but with a larger inline fan and a hepa on the intake plumbed to the box would be the same???

[@tommykarlsen3245]

I have been thinking of something similar, only with small hepa filter (for vacum cleaners) and no extra holes, so that it would be positive pressure all the time. filter and fan in the back or top and air exiting through the holes where my hands go.

[@LbaTR05s]

I bought an intake fan for a pc and a 6"x6" MERV13 air filter and used that. I get my positive pressure pushing out of the hand holes instead of drilling the extra holes.

[@freddymyrick1852]

Exactly what I was thinking

[@christophertucker900]

Yo Willy what does that meter read in front of a flow hood? I wish u would have done a comparison...

[@Zlaptheentity]

I was also wondering this. It’s a good way to figure out just how well this works vs. the best equipment out there (a flow hood)

[@jamesstaplesv]

SO GLAD TO HAVE FOUND YOU BACK; YOU ARE a hero of mine, thanx sooo much. Someday $$ follow. !!

[@mindfulmagic]

Both Blotter Art Pieces I have in my room LOL, the sunshine is signed by 3 of the Brotherly Love members, simply amazing :)

[@sparkeyjones6261]

Brotherhood of Eternal Love? So, Casey Hardison, William Pickard, and Tim Scully? That's awesome.

[@mindfulmagic]

@@sparkeyjones6261 10-4 will post pics when I get to it

[@mindfulmagic]

AMAZING I LOVE AND COLLECT, will sell soon

[@sparkeyjones6261]

@@mindfulmagic Very cool, I'll keep an eye out for them.

[@mindfulmagic]

@@sparkeyjones6261 I will get around to it eventually man :) got so much to do in this house before summer...blotter art is amazing though. Simple times I sure miss

[@williamcozart8158]

"trippin' on acid in a hotel lobby, errything movin' hella fast Ricky Bobby'" Those some genius lyricisms right there.

[@TURK_182]

You're being sarcastic right

[@PatrickMeyer-f1m]

what is the advantage of air movement in the box? Wouldn't it be better just to have the box without it operate fan filter? I mean, the fan just increases the risk than if you use the box without a fan?

[@maroosk]

I always wanted to ask why people dont use quilt batting in rolls? Only a question. People stuff or tape but can't we use plastic filters and batting by the yard or is the pillow fluff cloud just better flow and super easy?

[@ppt513]

Looking for help because I must be missing something. I followed the instructions and bought the same fan as Willy. I first tried merv 16 and there was no airflow through the filter. Tried merv 13 and same thing. I'm now down $90 in filter material and all I have is a tub with holes in it. Very disappointing. Anybody else try this and find the recommended fan too weak or have any thoughts about what I could have done wrong?? Many thanks @willy'sworld

[@ryanpongracz8051]

Also your description of this being a negative air pressure system is false. This is positive because the intake flow is higher than the out take flow. In order for a flow to be negative there would have to be a seal to the environment to start, and the air intake would have to be lower than the outtake therefore making a suction effect in the intake flow and creates a slight vacuum to the room, thus making it negative pressure. This is definitely positive pressure.

[@caje5658]

OK I have two points to help out all the people below having problems with 1. not enough pressure to push air through the filter and 2. the people who are concerned about air moving in the box. 1. Its a bit of work, but if you disassemble the A/C infinity fan unit and turn the individual fans around inside the unit. the fan will now be sucking air through the filter instead of trying to blow it through. The air wont "bounce" off the filter. now install the fans INSIDE the box so its sucks air through the grill which is now outside the box and is sucking air through the filter into the box (still positive pressure in the box) It takes up a bit of space in the box, i know. but it works better. 2. The reason we want STILL air in a SAB is because the air isn't filtered, Its full of particles. we want the particles to settle out of the air and on the surfaces of the box, so it does not land on our culture/spawn/agar. but once the air is filtered and there are longer any particles in the air. it can move around all it wants. because there are no longer any particles that can settle on our culture/spawn/agar. I hope this helps a little

[@kittenvibe7599]

@willy’sworld I built a monobox out of a litter box led strip grow lights a bullet shell and pvc pipe and I have an airflow problem I even switched the puffs to make them less dense and I’m still having an airflow problem any ideas on how to fix it

[@FYahooo]

Why didn’t he use a HEPA filter?

[@TURK_182]

Most of what you said was unnecessary and you didn't even go over the dangers of UV radiation ☣⚠️

[@mikecurry6847]

I worked in the inoculation lab at a really big mushroom plant. I swear, I was the _only_ person there that respected/understood uvc. I was always telling people to be careful and to not look at it but usually they'd just kind of laugh it off lol

[@alext8610]

@@mikecurry6847 They ain't gonna be laughing when they get cancer and start dying by age 45. Keep doing the right thing bud! 🍄❤

[@LuckyChucker]

Yes. I think recommending the UV light is a really bad idea. Willy seems to be a great dude, and I hope he corrects his message to the people.

[@Chip1189]

leaving that light on wont kill youre spores?

[@slimgrows]

Joined the 20 dollar tier my guy

[@robertharrelson8655]

The way the other box works is the fan is inside the box and pushes the air out. There is only the one opening. The one you built would be better if the hand holes were sealed off like a glove box.

[@johnstamos4629]

yea.. it doesn't make sense to filter air on the way OUT. LOL

[@paulyssacharides4690]

Yo I can’t find a “Pan”cake video anywhere’s

[@bobblew8530]

I have limited space so I use a clear comforter bag and a desktop HEPA to make a positive air chamber

[@wickedjack1222]

Put a few layers of the filer material in, wouldnt that cut down even more contams ?

[@witchdoctorguru]

You would think so. I built one and installed MERV 17 filter medium. Why not? right?The fans are too weak to blow through it at all. So I ordered MERV13 and the flow you get is adequate to pressurize your box if your vent holes arent too big or too many. These fans are not strong. There is actually more air blowing out the intake as a result of back pressure caused by the MERV13. Doubling the MERV13 would probably stop the air flow altogether like the 17. You need adequate pressure to be able to keep particles from entering the holes. That being said MERV 13 seems to allow adequate pressure at the vent holes with my arms in the arm holes. How well it filters remains to be seen. I'll report back.

[@Dillyg978]

Willy please increase the master volume on your videos. I find at max volume its very faint

[@MCT812]

Where can I get a mask like yours Willy? TTF

[@TheSaltyOG]

This is a question I can get behind! lol

[@danvelazquez1649]

Yo man where is the link to that UV light so I can get one

[@markbaker1286]

Mush Luv to the Trip Team Fam

[@dadec22]

You’re a legend Willy. Thank you thank you thank you

[@hea92484]

I have that exact light, but I don't use it because of the ozone it produces. Plus I read it will burn you/blind you. I got it for something like this but all I read made me nervous.

[@hea92484]

If you know more, please enlighten me. I know I'm dumb, and always looking for better information.

[@timothywhite3465]

It will cause UV radiation and potentially skin cancer and the ozone will cause cell damage in your fucking lungs. Did i miss him mentioning the dangers of that? Or did he just tell all his followers to go get fucking cancer. Jesus man.

[@constantringingtech2230]

@@timothywhite3465 sometimes (most of the time) he tells viewers stupid shit. He needs to go back to basics.

[@timothywhite3465]

@@constantringingtech2230 i think honestly its because he doesnt go off any type of script at all and forgets important details like, DONT POISON YOURSELF. Bitches be watching these videos because they are new. I mcguivered mine and still use it and let my plates dry in it with the fan off and the doors closed. My shits a little classier in some ways a little ghettoer in others lmao but I have a UVC that i dont fucking use when im even in the room because its dangerous.

[@dambirtrogech3976]

Lol, you guys are talking like you're gonna live under that light. A few hours a month won't do nothing to you, relax.

[@ronaldtownsend5745]

The fan should be mounted so as to create positive pressure within the SAB. In other words, the fan should be blowing air into the box. The filter should be a HEPA filter which will trap particulates down to 0.3 microns and keep them from entering the box. The positive pressure will keep particulates from entering the box from all the holes that have been drilled in it. I personally would not drill the small holes in the sides. The holes for your arms should be enough. If you are making a gloved box then you need the holes in the side.

[@TOPskunkfisher]

Did you watch the video it is setup to produce positive pressure, this is a killer budget flow tote not a professional laminar flow hood, clearly not the same but definitely better than a still air box or nothing at all and it's a minimum investment

[@ronaldtownsend5745]

@@TOPskunkfisher, Yes I did, but I missed the point where he said his fan is mounted to produce positive pressure. The original design produced a negative presure.

[@freddymyrick1852]

The small exhaust holes should be eliminated the arm holes are good enough to push contaminants out from the source which is you

[@apepanthera]

Hello guys. I'm new to mycology, just did my first grain preparation, autoclave sterilisation, inoculation about a week ago. Needless to say there is a fair bit of contamination but I'm glad I got that out of the way and I'm ready to do it again, this time on agar in a still air box. I have a chance of buying a 2in1 beurer EPA purifier/humidifier (110$) and I'm fiddling with the concept of whether running it for an hour or so in a chosen innoculation room coupled with a simple still air box setup would work. The model of purifier seems not to come with HEPA filter but rather EPA filter, even though the small research I've done indicates mold spores are relatively big (4 microns). Is this setup better/cheaper than building a laminar flow hood, considering the machine also has automation functionalities, which seems like a perk when it comes to fruiting. Thanks anyone

[@c.odubhlaoich2948]

Cheaper, yes. But a legit flowhood really can't be beat. A lot of people would also probably tell you don't even worry about that set up and just make sure you have sterile procedure down with a simple SAB though. Get a towel wet and ringed out with 1:10 bleach/water, lay it out flat and put your SAB over top of that and have some kind of cookie sheet or something to elevate your tools and jars off the towel, and spray the insides of the SAB with soapy water and you're good to go. Anything more than that is really just peace of mind, so flowhoods are really nice just because you can work openly and know youre doing it in a clean spot, but plenty of experts know that a simple SAB can be very sterile.

[@thejohn6614]

@@c.odubhlaoich2948 why the bleach/water towel? So it will gas off and kill things in the air?

[@c.odubhlaoich2948]

@@thejohn6614 No, you don't even need it, just damp with regular water is fine, bleach is just a bit more protection. You just wet it to help catch any mold or bacteria that might fall to the floor of the SAB

[@thejohn6614]

@@c.odubhlaoich2948 i see. Thanks

[@rajum5817]

.can any one suggest any good website were I can get the kit deleverd to India and spores ...plz I need your help

[@TheBookofLab]

the real test is to do some sloppy agar work in there and see if they contam

[@paulyssacharides4690]

There’s a lot of hepa filters to buy in the internet that would work great.

[@JohnnieKatsMind]

Won't you burn your eyes if you keep the uv light on?

[@williamcozart8158]

N... no. Just don't stare into it.

[@TURK_182]

Yes

[@TURK_182]

@@williamcozart8158 look at the thumbnail, the light is gonna be in your eyes the whole time your using it, Willie is very irresponsible

[@williamcozart8158]

@@TURK_182 No, that light is not going to blind you if you used it in this way.

[@williamcozart8158]

I mean for one thing it's INSIDE the plastic bin, that right there will filter and diffuse enough of the uv to not blind you.

[@MattRoadhouse]

I use a HEPA, UV-C, negative ion "air cleaner" unit with optional ozone generator (rectangular box that's like 6" x 8") - mounted into the short side of a tub with the opposite end of the tub cut open for the workspace at the end of the clean air tunnel. Setup workspace at the end of a 4' folding workbench

[@flowerspower2345]

Your setup sounds nice. Any chance of uploading a photo of the setup? thx.

[@soithascome2this]

where do i get a fan like this ? ... can't find anything on ebay

[@zoghunter82318]

Man, willy use to make way better videos before he started his patreon, use to be his videos showed the tek, now his videos are 95% just showing himself 5% the tek. He also use to make way more videos. Every time a good channel starts a patreon, the content goes to shit.

[@aled721]

Sadly this is more to do with KZbin ad revenue, KZbin is to find new people. Try Reddit for more in-depth research and info.

[@The_Google_User]

KZbin doesn't even put prerolls on his videos, he makes 0$ from youtube and if he shows too much they will ban him AGAIN

[@aled721]

@@The_Google_User yes, so how can he make money? Or do you want all his info for free?

[@Thesacrednetwork]

What filter material?.?

[@dienosorpo]

UVC light looks really cool? Really? Even tho most UVC lights cant penetrate clear materials, sticking your hands into a container with UVC light is such a stupid idea... and some of the UVC light will make it through the plastic container soo.... Please learn about saefty precautions with UVC light...

[@martinsteele5171]

Hi am I right in thinking that you aren't supposed to expose your eyes to u light it makes them very sore.

[@Perryloc]

I don't think you want to expose yourself to light while it is on. Unless there is a different type of uv c light. I know they are in hospitals but they are up high with fixture on bottom.

[@philipjnz9923]

Hey did you take down the video where you did the review of shroom supply grow pack?

[@LuckyChucker]

No UVC!

[@TheTubejunky]

This is not that great of a suggestion! Good luck willy. I like you stuff man but with all your experience you should know better. Good luck my dude. I went from glove box to still air box and works fine for agar. This is going to create air flow and a lot of it. Depending on the level of airborne tams in your environment it's going to spray your work. Hope you guys figure out what works for you.

[@cerealkiller8921]

It's filtered, lol.

[@ryanpongracz8051]

Why is the position of your filter catching the debris IN your box? Why not attach the filter to the outside and catch it in the filter before the air enters? That way when changing out it's also less likely to get anything in the box.

[@ryanpongracz8051]

My solution was to put one pre filter on intake side, and two stacked on outtake side. Encased fan in filters to stop contams. Will kill fan faster than intended, but who cares, they are cheap and this works way better this way.

[@manny8039]

I’m pretty sure uvc light is extremely dangerous for human skin and is not safe for us to be around , this scares me

[@Loki_Morningstar666]

actually uvc is considered the safest uv light source for use in tanning. Most newer tanning beds use uvc. Its uva and uvb that cause cancer.

[@manny8039]

@@Loki_Morningstar666 you can look it up uvc is installed in air vents to kill the bacteria and that’s about as far as they go with it because uvc rays that make contact with skin or eyes will cause damage , according to The FDA.gov

[@michaelroe8547]

🙏🏻 Willy!!!!

[@CheifinKeif]

So I’m building this step by step and it appears mine looks like a negative pressure system my fans brackets are on the inside of the tub that means its blowing out right??? Mush love

[@CheifinKeif]

Sooo i flipped the fans and then it just stopped working. Fug this flow box lol i was having success in my SAB just wanted an upgrade

[@wildman2894]

a hot coffee can works great and a copper 1 inch pipe works for vent holes do it outside for air flow heat with torch

[@mikelilly538]

Willy where did you get the hoodie!???

[@JohnKomp]

Good info but I'd love to see more of what's being talked about, less of the speaker. I learn better by seeing as well as hearing.

[@garryneyman3300]

Could we use MERV 16 Filter material to improve the filtration rate and would that lead to better results ?

[@jasmineohara4751]

Did you end up trying it ?

[@LuckyChucker]

Willy! You must fix this! Love you dude! No UVC

[@dienosorpo]

Whats wrong with UVC?

[@LabelsAreMeaningless]

@@dienosorpo Really bad for skin and eyes. Pretty sure it would hurt the mycelium as well. Never leave it on when working. It could be good to toss on 15-20 minutes before work and then shutting it off.

[@jamesstaplesv]

Gluteraldehyde, is an excellent Spore penetrator, thus hammering hell on any mold spores. pricey, maybe, i will report bacl.

[@michaeljoyce6683]

I just wanna know where to buy the masks from.

[@junniedoggjayday774]

I used a air purifier fan with a filter

[@hunterreddin5366]

could you put a air purifier ina SAB?

[@burnin4buddha713]

And two years later you don't hear about anyone using them so I'm guessing your assumption was correct and they don't work better

[@ShroomShaman]

I wonder if a Merv 16 would work. After all it promises .03 um purity

[@sin-lab2791]

Ok so made one same fan lil dif filter lil cad and alum tape! I've now poured over 100 plates, transfers, and a wild oyster clone and 0 contam I'm honestly baffled and don't know what to say it's amazing so far! Fb me for pic if intrested

[@johnstamos4629]

cad? do you use a UV light too?

[@sin-lab2791]

@@johnstamos4629 cardbord aided desighn and no uv and yes worked ok for a time' have since upgraded.

[@positivevibesveda]

@@sin-lab2791 what’s your facebook?

[@sin-lab2791]

@@positivevibesveda absolutely worked great had around a 98% contam free will work if done proper i did not use uv light just the filter

[@XxCHATTELSxX]

Hey Willy! I'm a new subscriber and love your work and vids. If I may, I have a special request. You never here anyone say what strain they have, or what strain is the absolute best. Is there any way you can make a video about the different and best strains, best techniques for the particular strains and ware to get the spores. Mabe how long to inoculate before fruiting. Kind of a crash course for beginners who want to succeed. Thank you so much for taking this into consideration. You guys are amazing and I look forward to your new videos!

[@lorentzianmanifold718]

No he can't and if he does it will just be shroomery posts he reads and makes a video!!! Willy the joke!!!

[@jojoex9073]

The UV light would kill the spores also if it kills bacteria it kills everything else

[@stynski86]

Good work but omg you gesticulate so much lol 😂

[@wildwilly1363]

👍

[@nutri8healthylife233]

Is UVC dangerous to eyes and skin ???

[@brettlatulip67]

No laminar flow to the design. Turbulence will mix everything.

[@mikecurry6847]

That's honestly kind of what I was thinking. That being said, he does know how to calculate laminar flow as he's done it in another video. He didn't mention it so maybe he didn't, but he very well could have done the math to figure it out.

[@mikecurry6847]

I would think that even if it was laminar flow, the improper filter would still be an issue especially over time.

[@dannyboi7695]

21:00

[@yvonrouillard9755]

Interesting video, tanks for this

[@msbeth420]

Thank you so much for sharing ❤️

[@CheifinKeif]

Cracked the fuck out of the container soooo easily I’m pissed

[@CheifinKeif]

went and got another tub and used the reverse drill method i saw on another comment and it worked beautifully!

[@theaveragefarmer5635]

I really what to know the song from your vids hotel lobby song thanks

[@gulcinbetiner]

Wont the uv light also damage your cultures?

[@dressedanddepressed2301]

Nope! I work with one in my SAB and even put it on time to time in my incubator and it won’t penetrate the plastic or glass that the mycelium sets in. If you removed the lids then exposed it,it can cause mutations etc

[@dreamweaverskennel2952]

Made 100% successful your a real one willymyco!!!!

[@Thee-_-Outlier]

This is similar to the bag method. I like the UV idea. A little closet with uv lighting and this positive flow device can make a good budget lab.. I would flip on the UV and use the bag method by turning on one of the HEPA purifiers they use in that tek on a little table in a closet. Let it run with light on for 30 min the enter and it should be pretty clean, minus you lol

[@timcanup8522]

Willy is a great person but I don't agree with this setup. I also don't agree with the rude comments, you guys need to somehow get willy to get you a bag cause your mushrooms aren't working.

[@paulmildner6093]

Hey everyone, I need your advice/help! I inoculated a rye grain spawn bag with golden teacher spores abt 6 days ago. The makeshift injection port didn’t seal up right so I taped over it. I keep the bag in a rather dark space inside a tote at room temperature. I haven’t seen any mycelium yet Idk if I should be seeing any or if I’m doing sth wrong.

[@genghis_quan]

Now AC infinity is repping the mycology iculture AND the cannabis culture

[@getbrainseeds]

i got a 8 inch ac infinity pushing air into my filter in my cannabis room and i love it i never have once had any grow problems and never get odors thanks to my filter, ac inifinitys are nice

[@anthony7788]

Grommets bro. Grommets!

[@douglundy5755]

thanks for isolating your virus on video..And do you ever conclude any information? I keep fast fowarding hoping to hear some information. 'splaining how to drill holes is not mycology...so you used a 'filter material' rather than paying $20 for a hepa air filter as the others have done? Ok I get what you did..Nothing about the results of your experiment and how it performed which is what we would learn from. Still telling us how to drill a hole..OK I took shop in school, but no I didnt need that class then either.

[@danielduncan2672]

Willy my boy youve got a lot of great content. Tons of valuable information, tips & tricks! I gotta tell ya bro you really screwed the pooch on this one! I followed your direction to a T! Tryin to push air through that filter material with those tiny little fans is like tryin to blow a fart out your ear! Fans could barely move air to the other end of the box without the filter? The UV-C doesn’t have high enough nano to do anything except piss off a germ! You lost ALOT of cred on this! It’s a great theory but you need to sharpen your pencil on this one! Much Love!

[@rileeyjanaee4834]

The price of the fan has doubled 😭😭😭😭 39.99$ Now

[@mycomama4209]

Has anyone actually tried this? Does it work? I think I will stick with my actual flow hood and a regular SAB.

[@pyrogee33]

I've tried it, works perfectly fine. Not 100% contam free. I get maybe 1-3 contaminated plates out of like 40. Usually get contams with swabs not transfers. But it also comes down to sterile technique. I also have 3 sterilizing UV-C lights instead of regular uv light.

[@mycomama4209]

Yeah I got the stuff to make this but never did. Still getting 100% no contans with my DIY SAB and my flowhood.

[@alancarr195]

It really needs better fan/filter set up, 4 in inline grow tent/carbon filter type fans are only 25-28 bucks on ebay/Amazon, using one those and least HEPA filter and secondary filter with the UV-c it would be a lot more effective I'm sure. The filters in the fan are just not enough

[@mycomama4209]

@@alancarr195 I bought a flowhood. Lol.

[@jeebs2009]

This guy likes to hear himself talk

[@mnemonic5819]

sharing info requires talking. go back to facebook

[@Heyron420]

I'm thinking an angle grinder would be perfect also. It's like a giant dremel tool.

[@dannyboi7695]

What uv light should i be looking for?

[@oscar_delicsonig8389]

Order from adam_shrooms on Instagram...He sells psychedelics discreetly and recommends too...He got shrooms,Dmt,Lsd,dope asf🍄

[@constantringingtech2230]

Where does one get the particular measure device?

[@omma-llama7860]

It's called an air quality monitor, detector, analyser, etc.., you can find them on Amazon. If you want the professional level indoor air analyzers, you can get those from Grainger.

[@constantringingtech2230]

@@omma-llama7860 ty

[@splattered63]

Willy PLEASE upload ALL your videos to RUMBLE. PLEASE

[@jamesstaplesv]

it is not pretty but i use a wood burning pen. no breaks