The same thing happens to me, but the white launcher thing gets stuck in one position, and I can't rev the blaster. How to fix?
@hongrand9 жыл бұрын
Same to me, I really need an answer.
@ElmoNL509 жыл бұрын
You dont know how to fix it ok so wat are you going to do get the rubber flappen out
@DaddyNoahontop9 жыл бұрын
hongrand take clip out
@MRFailKing7 жыл бұрын
Korex Studios. .same
@kasperfk7 жыл бұрын
You have to open up the blaster and take out the orange box behind the magwell and unscrew the screws and take it apart, once it's open you should be presented with a wheel with a little dot which spins when the gun's trigger is pressed down, and usually it jams in one position and you need to jiggle the wheel a little and push the arm (that pushes the dart out of the blaster) and put everything back together and everything should be fixed.
@Jonny_____11 жыл бұрын
I've removed the rubber thing on my rayven and it does make a difference, it hardly ever jams now
@BasicNerf11 жыл бұрын
I've removed the white jam skirt/rubber and it's reduced my jams a great amount. Also if you watch the video again, the darts are coming. Their just getting stuck somewhere at the top of the mag/rubber skirt area.
@chrisgoodman73384 жыл бұрын
Are the rubber skirts used to guide darts?
@rygelbaladad41338 жыл бұрын
i think the cause of that is how you load your darts in the cilp because sometimes the darts stuck inside the clip, then it pushes the dart not properly.
@kingraptor34578 жыл бұрын
Ok, use pliers and go through the jam door and grip the rubber skirt, then pull, that will remove the rubber skirt. It will also increase its range + power
@RexCT756711 жыл бұрын
This happens to my Stryfe all the time. I just chuck the dart and reload the mag and move on. Probably dart quantity. I use all used darts as well. And since the Roughcut came out dart quality on my end is horrible because the tips are being destroyed when people load the Roughcut..
@Hzburdick11 жыл бұрын
It will be totally fine if you take that skirt out, everyone did it in their Rayvens
@BasicNerf11 жыл бұрын
Try inserting an empy mag/clip. Make sure the blaster has fresh batteries in them. And then hold down the rev trigger, and then push or tap the fire trigger. That should get the pusher back into place.
@crusaderonthebox4 жыл бұрын
Basic Nerf I’ve also taken the magazine out, pressed down of the white buttons in the mag well, which lets it rev up, fixing the problem
@loco51696 жыл бұрын
How to fix it: Take out the mag, then you can reach to get the dart or you can do it when the mag is still there
@anandnair11843 жыл бұрын
this happens to my hyperfire. most easiest way to deal with this is to put less darts cz when i put less darts in my hyperfire magazine total capacity 25 , i put 17 so it dosent jam it happens when the dart is going forward the down dart will push it up to cause the jam so put less darts and try it
@poffusagi265810 жыл бұрын
But my Deploy CS-6 IS. KEEP. FREAKING. JAMMING!!!!!
@nitra019 жыл бұрын
Deploy fuckingmsucks
@banana_in_a_tuxedo5 жыл бұрын
@@nitra01 shut up you mindless sheep
@atnorange54915 жыл бұрын
@@banana_in_a_tuxedo it's true though. The deploy always jams and it's really hard to put in a magazine.
@banana_in_a_tuxedo5 жыл бұрын
@@atnorange5491 yeah but it doesn't mean people aren't allowed to use it and like it. Sure, i was a bit harsh (sorry bountY) but the way he said it sounds like he was one of those people who just say that the deploy sucks just cuz everyone else does. Iv'e used a deploy and it didn't jam and the mag well wasn't the smoothest but ive seen worse. Therefore, i think akie's deploy is either old, damaged, badly cared for, or just a lemon.
@imabrokebeebidiot77414 жыл бұрын
Me too, is very not good the wonder they stop selling it for this model because sucks 😒
@Sigh_itsDavid11 жыл бұрын
it is basically the dart quality and because of the revving of the two front motors, if you want to eliminate the problem stick two RM2 motor into the flywheels. Im saying this because everytime the dart is fired the motors rotation speed drops, so by changing the motor to a powerful one it will not drop that fast
@Kuanhui11 жыл бұрын
i had the same problem on my rayven too, it might be due to the dart quality, all i did was just spray some WD-40 to the inner side of the clip where the rubber tip of the darts are facing, and now the problem is solved
@toastyboy51474 жыл бұрын
don't know why i'm commenting on a video this old but the rapidstrike seems to work fine with the accustrike darts. I don't really know why, but i didn't have the jamming problem with the accustrike ones like i did with the n strike elite ones.
@joshuajones611311 ай бұрын
Still appreciated, thanks!
@KempoSensei10 жыл бұрын
Came here looking for help for my son's blaster that stopped working. The white pusher stayed out. I happened to have 2 extra batteries and tried that, and it made a difference, so if your white pusher stops working, try batteries. (the motor wouldn't even move so I thought the thing was dead, and we just got it last week).
@danib55384 жыл бұрын
Its mainly the quality of the dart because the main cause of a jam is when the pusher pushes the back of the dart but the dart bends out of the way of the pusher not allowing the dart to be pushed into the fly wheels or the pusher might not have the power to push the dart into the fly wheels so in that case just change the batteries
@medalgear6546 жыл бұрын
I have a different problem with my CS-16. Just Added new batteries but my gun won't shoot and it's not even jammed. Can someone help me.
@swager64024 жыл бұрын
You have a better Rapidstrike then I do I don’t like the XD Rapidstrike because it’s not firing fast enough
@Ron_381311 жыл бұрын
Try using a old stampede magazine instead, they have less pressure on the darts. It is the magazines actually. Stampede magazines work fine for me.
@oneinsixcom10 жыл бұрын
Jamming too often. If you watch the darts rise up from the magazine sometimes it is slow to pop into the firing chamber due to either weak magazine spring or the mag is too slim hence friggin darts rubbing as they try to rise on up and the firing hammer hits emptyness before the dart gets loaded throwing it all out of sync. Taking apart the magazine is impossible without breaking it. Might be better with slimmer darts but then it will cause further problems in the chamber. The magazine needs to be wider. Can try oiling it so darts don't catch in it. Useless thing. Must be made by GM.
@mrwhoperz79799 жыл бұрын
So true.
@harveybarton75557 жыл бұрын
Bobby Nikki i take apart mags all the time it clean them
@ContainmentCrew11 жыл бұрын
Mine has had a lot of problems right out of the box as well. If this is indeed jamming up at the skirt try removing it. If the darts are used and a little too soft/used they might be bending from the pusher and not making it through. This doesn't look like a motor as the darts aren't making it that far in correct? Sounds like the flywheels are still spinning free.
@shootoutthelights10 жыл бұрын
one possibilty causing jamming could be the orange rubber part of bullet is catching or sticking against the magazine before bullets are fired.....
@shootoutthelights10 жыл бұрын
my son thinks that if a different mag was used it would fire better, eg. 35 dart drum mag.....
@austinlee91474 жыл бұрын
That’s why Nerf improved it and released Rapidstrike Elite XD!!
@crusaderonthebox4 жыл бұрын
Austin Lee I have one. It still has the problem. Maybe because mine is australian it still has the problem.
@tjthegamer33544 жыл бұрын
The rapidstrile XD is just a reskin and it shoots slower
@GriffenSpadeIsBack4 жыл бұрын
the pusher in my stratohawk doesnt even move at all which im pissed about cuz i paied $64 for it.
@ebolian.81474 жыл бұрын
I got my 2nd rapidstrike for $6
@CreativeGuy82310 жыл бұрын
If you pull the trigger while taking out the mag it wont jam
@CreativeGuy82310 жыл бұрын
your welcome
@ДианаГеракьян10 жыл бұрын
That doesn't work for me :(
@virtumin15985 жыл бұрын
Total Destruction you just replied to yourself
@callofgamingwithishan40785 жыл бұрын
It no work bro
@mudzakeerzack77059 жыл бұрын
Now I fixed it and many jams are caused by the spring of the magazine of the gun try pushing the darts down when it is fully loaded if it not get back into its place its mean your spring is not strong\weaken
@Suiax9 жыл бұрын
At least yours sort of works. My doesn't even push the dart forward.
@zackalchemy8607 жыл бұрын
Try loosening the rubber skirt if you can
@vmanic6 жыл бұрын
how?
@rokroxon54023 жыл бұрын
My problem is when i bought new batteries for it shot like normal it shot far firerate was good now a day later range is like 5-10 meters and firerate is slow its got a lot of jams i will try to replace the batteries
@h.k.92988 жыл бұрын
Ik the prob its actually the darts moving into the place when u fire them the darts slow down leaving the thing pushes the front part while the back part is down
@antihero69883 жыл бұрын
My access door is jammed. It only opens a tenth of the way and then stops as if there's a lock stopping it from fully opening. Anyone with any tips?
@hardcoregamershibe43382 жыл бұрын
First of all your darts are have some very tiny scratches. First take a paper bag and a hair dryer Step two.swicth on the hair dryer and put it on max heat Step three .put your darts on your paper bag and dry it 30 seconds with a little shake
@AwkwardHypernerd4139 жыл бұрын
I have the same problem with my XD rapidstrike. Will it be better if I get rid of it he skirt?
@JelliThePilot11 жыл бұрын
Whenever it happens to me, i need new batteries. Usually the pusher won't go back, needing new batteries. Hopefully nerf issues a recall which fixes the problem
@samdigby131911 жыл бұрын
I do have a rapid strike and had the jam but the mag or clip is in line with the fly wheels so I don't know why nerf put in the rubber flaps
@aaroncooloffyu5 жыл бұрын
My stryfe does that ones in a while i have a camo and orange one btw
@sarp85944 жыл бұрын
jabroni17 _ most semi auto or fully auto nerf guns do that the best way to fix it is to check dart quality before use also the stryfe trigger can sometimes jam and to fix that you have to slap the stryfe
@moosi2378 жыл бұрын
It's based on how you put the darts in the mag
@MugenCivic3 жыл бұрын
I put it on the middle of the mag
@harjimatharu97359 жыл бұрын
so how do you make itnot jam becuz i have the same problem plz quickly answer i have a nerf tournament at my school coming up in about 3 days plz help
@p_42253 жыл бұрын
It’s like this cuz batteries are low, it’s happened to me and when I switched my batteries it went to normL
@tiantian3296 жыл бұрын
I used 3rd party “waffle” darts because they are cheaper and more accurate. My Rapidstrike works fine if I load one waffle dart into the mag, but if I load more than one the blaster jams and the flywheels stop revving completely. Then I have to take the mag out and it looks exactly like what you showed us. Any advice?
@jamesnixon584110 жыл бұрын
its probably because of the rate of fire combined with dart quality
@ProWeiJun11 жыл бұрын
The problem of jam is because of your clip system. Try hitting the bottom of your clip system and it will work.
@jakeroberts896111 жыл бұрын
Yet why does it do that when its older version doesnt
@insertname94754 жыл бұрын
I got the new nerf rapidstrike with the repainted mag and stock and it keeps jamming! I didn’t see the rubber curtain or anything, and it just keeps jamming! I have a Nerf war event coming up and I really wanted to use this gun!! Someone plz help!! Edit: the nerf darts I used for the rapidstrike r perfectly new, right out of the box, and it still jams!
@nobuenozone362910 жыл бұрын
the skirt is the main problem also, the new clip the spring will be to strong so, weaken it
@raulbelmudez81523 жыл бұрын
I just bought mine and it doesn't shoot manz need help
@hongrand9 жыл бұрын
My Rapidstrike's white launcher won't go back, and I can't rev up the blaster. Any tips?
@DaddyNoahontop9 жыл бұрын
Put clip in and out
@winter23728 жыл бұрын
+RyanHong [Hongrand] bad wiring, go to the nearest workshop or hardware store to repair
@wabi470211 жыл бұрын
Isn't it bad for the blaster?
@Stxphennn9 жыл бұрын
What would happen if i take out the rubber skirt for the darts? Will it perform better cus everytime this happend its been stuck on the rubber skirt
@winter23728 жыл бұрын
+COOKIE GAMER123 the reason why the rubber skirt is there is to stop the dart from firing fast. but you can modify it to fire rapidly by removing it but im not recommending it cause it will more likely to jam
@dharmendramishra3036 жыл бұрын
I have the same problem with my nerf elite stryfe (xd)😭😭😭 please I beg for help
@hecker97534 жыл бұрын
Me too
@dominic22818 жыл бұрын
My Problem is that the Rapidstrike is not very powerful and the batterys are low after short time
@dominic22818 жыл бұрын
VY Canis Majoris Now solved this issue: just bought 3 photobatteries with 3V and then put them in a line in the storage, you need also 2 old normal ones for the other line. I used a little pipe, that the batteries fit. Now it has 12 V which is enough.
@arthurshreds85278 жыл бұрын
my rapidstrike's pusher mech gets stuck and doesn't work
@patrykkruk29048 жыл бұрын
+ElitePhoenix32 yeah mine too
@arthurshreds85278 жыл бұрын
its a lock, it think
@isaaccolletti22578 жыл бұрын
My does also
@hazeldalangin37377 жыл бұрын
SpartanDonutGD '
@sageanbu31237 жыл бұрын
you p8t to much dart
@Meeperstein1019 жыл бұрын
Do you know how to remove the rubber skirt?
@morganfe58039 жыл бұрын
Me I had a rapid strike I fixed jam by changing the battery you should try
@chitozc31568 жыл бұрын
What kind of batteries do you use
@edwardperez-herrera787011 жыл бұрын
my pusher won't go forward i think it's broken. i bought it from walmart on wed. oct. 30th and i need to fix it by friday PLEASE HELP :(
@ProWeiJun11 жыл бұрын
How do u remove it, by opening or just cutting it in the jam door?
@ryancadil12449 жыл бұрын
Anyone Could Help Me Fix My Nerf Stryfe Ive Removed The Locks And The Censor And The Gate In The SpinWheel.... What Should I Hella Do!
@winter23728 жыл бұрын
+Ryan Cadil not good......... by removing the gate in the spin wheel it will jam !!! better put it on again
@samw8 жыл бұрын
I bought mine today, and it makes horrible rumbling sounds. PLEASE HELP
@whimsical22237 жыл бұрын
staradar5 bad battery's if you use the same type you'll still have the problem
@samw7 жыл бұрын
thanks m8 i will try that
@cynicalchill7 жыл бұрын
Did it fix yours? Mine does the same rumbling.
@catherine60258 жыл бұрын
Hi, my son's nerf stopped to function even though he changed the batteries...help me...merci
@winter23728 жыл бұрын
+Catherine Thine what the nerf name or what it look like ? i can help you with that
@squidwardtentacles2447 жыл бұрын
I have the same problem on my modulus ecs-10 help me pls.
@thempire452310 жыл бұрын
this happened to me and i found that if u use new batteries it wont jam as often. my rapidstrike is modded now so i use 4 trustfires and this never happens so YOLO
@soaringdoge67267 жыл бұрын
the same problem happens to me to and it happens to me if I have a fully loaded mag or almost loaded mag.
@MugenCivic3 жыл бұрын
Same problem happen in my demolisher...
@cod2bros4728 жыл бұрын
That wasn't helping u were just showing people u have the same problem
@SneppySymphony10 жыл бұрын
My rapidstrike does jam too. However i fixed that by just putting 2 pieces of tape on my clip.
@jgrover27359 жыл бұрын
can u make a video on where u put the tape cause i seriously need it i would subscribe
@fernystein95169 жыл бұрын
+F.U.C.K where did you put the tape?
@clarkpraiseong2944 жыл бұрын
Just put oil or wd-40 the white one that pushes the bullet...my nerfs work again..
@EXTREMERC4168 жыл бұрын
I think its the magazine jam friction or it can be your dart is a little bit too smal i think
@EXTREMERC4168 жыл бұрын
The second jam is because of friction of the magazine that why the xd version shoot a litle bit less faster like 3 dps (the original is 3.5 dps)
@EXTREMERC4168 жыл бұрын
And reload your clip corectly
@harveybarton75557 жыл бұрын
RogerNerfclub ooo wow
@alfalfagaming50828 жыл бұрын
its the dam mag it shoves all the darts and the battery quality such a shame i love my rapidstrike but its sad that my semi auto stockade has better performance
@mrey56788 жыл бұрын
im getting rid of mine
@YutaaGamin4 жыл бұрын
Buy a fake one my darts always jam so i bought a fake one that has 30 darts and it dosent jam now! I used it for 1 week and my old one i used it for 2 days until it starts jamming my delta trooper!
@DrButterForce11 жыл бұрын
Mine does that, it can't be dart quality my first shot was one.
@theflynn3211 жыл бұрын
I often get a similar problem with my stryfe
@yungchangsta6 жыл бұрын
my rapidstrike doesnt work. when i press the start button it makes no noise and when i press the trigger it is fucking weak so nothing comes out
@jakeroberts896111 жыл бұрын
This happens so much with mine
@DingusDungus3 жыл бұрын
I ripped out that rubber piece of garbage. Now it never jams.
@edmund89546 жыл бұрын
How Do You Fire It That Fast Wtf
@tjthegamer33544 жыл бұрын
You just hold the trigger
@chehoswell80239 жыл бұрын
Should I cut the rubber out?
@MinecraftVoidMan9 жыл бұрын
Noo! The skirt is to guide the dart into the flywheels. You can take it out, but you'll get more jams
@winter23728 жыл бұрын
+Ninja carrot jam
@SwiftCraft7 жыл бұрын
+cubesicle you actually get less jams and better performance
@aragenx34708 жыл бұрын
Damn I have this and barely noticed
@AtoMatik9 жыл бұрын
Mine is like that but it dose not shoot even tho I have new batteries
@stringingprism8598 жыл бұрын
FURY_AtoMatik 562 qqqqqqqqq
@stringingprism8598 жыл бұрын
FURY_AtoMatik 562 qqqqqqq
@AtoMatik8 жыл бұрын
Stringing Prism qqqqqqqq
@yueh049 жыл бұрын
my rapidstrike also jams alot
@DrButterForce11 жыл бұрын
Things become perfect when you accept them for what they are. l0l
@hms_pics11 жыл бұрын
Just cut the rubber off it does not do anything
@d0golo60211 жыл бұрын
The skirt all I did was just cut it of and it's fixed
@devinhouston745610 жыл бұрын
Mine keep getting jammed too
@mastercoyote93498 жыл бұрын
Me too,just use another magazine
@sbcombopwnsnoobs6111 жыл бұрын
looks like a g36c must get...
@ninjamantask87103 жыл бұрын
I have the same problems
@irinhaque8893 жыл бұрын
bro my didn't work
@arthurshreds85278 жыл бұрын
it jammed with new darts for me
@tjthegamer33544 жыл бұрын
Same
@dabrackboy34195 жыл бұрын
My jam was the mag
@poffusagi265810 жыл бұрын
I DONT KNOW HOW
@dudelego79324 жыл бұрын
Same with the infinus
@MugenCivic3 жыл бұрын
Dude infinus is a good and pretty exoensive nerf i've ever seen how tf it can be
@handaru61579 жыл бұрын
Use koosh darts
@nerfdefender31411 жыл бұрын
Every gun i get is perfect
@nerfdefender31411 жыл бұрын
Well the world idnt perfect, but then again i take goid care of my guns
@TrezSix10 жыл бұрын
I just bought i nerf gun yesterday and it keeps on getting jamed HElP ME
@BasicNerf10 жыл бұрын
shannon lakin Why Nerf blaster is getting jammed for you? Is it the Rapidstrike, or a different one?
@TrezSix10 жыл бұрын
RapidStrike
@TrezSix10 жыл бұрын
I tried my other mag and that didn't jam but when ever i use the rapid strike mag it jams
@TrezSix10 жыл бұрын
I think i need to buy new bullets
@Censoredmovie258 жыл бұрын
+Trex 6six6 that could be the problem the newer. the dart the better