🔥 NACA Duct DIY Installation (Scoop, Vent, Inlet)

[@mikemontgomery7337]

Looks badass!!!

[@ThePaintPaperHustle]

Thanks

[@rodneyfelder383]

Hey buddy, the NACA duct turned out great.

[@ThePaintPaperHustle]

Thanks buddy!

[@keithgriffith6002]

Another great video thanks man.

[@ThePaintPaperHustle]

Thanks for watching and you’re welcome

[@freddiemoralez1536]

🎉🎉YOU ARE RIGHT THAT FADE PAINT (KILLER) . O AND I THINK THAT SCOOP TURNED OUT PROFESIONAL JOB. COURTNEY THANKS FOR THE CONTENT I ENJOY WATCHING 🎉🎉 .THUMBS UP AND GOD BLESS ALL. 😊

[@ThePaintPaperHustle]

Thanks a ton buddy

[@dennisallen9830]

Courtney you make it look easy. I don't have the guts 🤔

[@ThePaintPaperHustle]

You can do it!

[@wallygator5479]

Love all your videos. You are very knowledgeable.

[@ThePaintPaperHustle]

Thanks buddy

[@Justboostn]

You are entertaining to watch

[@ThePaintPaperHustle]

Thanks buddy

[@Amxracer]

Cool 😎. Let’s go !

[@ThePaintPaperHustle]

💪🏻

[@funfun8095]

Looks good. I was thinking mounting it with panel bond from underneath, would have looked good, too.

[@ThePaintPaperHustle]

Yea forsure but then I’d need to repaint hood due to unfinished edge where cut was made

[@frankietyndall9595]

If u could find some thin wall fittings could use a 45 degree bend would be like long sweep 90 force air straight into procharger

[@ThePaintPaperHustle]

Fitting or a hose / elbow for end of duct?

[@89_boostedsupra]

Awesome job man. Very informative

[@ThePaintPaperHustle]

Thanks

[@NoOne-uu2zt]

Looks good ! Congrats

[@ThePaintPaperHustle]

Thanks

[@mikeday852]

looks amazing

[@ThePaintPaperHustle]

Thank you

[@mustangal8534]

Looks good man and is functional also!

[@ThePaintPaperHustle]

Thanks and definitely

[@MartinMcMartin]

Measure once, eyeball 10 times, measure again and cut. Perfect. Or measure once, cut it and realize you fu#*ed up everything by rushing. Nice work man.

[@ThePaintPaperHustle]

You’re right. Thanks man

[@shawnbraden6689]

Looks sick man

[@ThePaintPaperHustle]

Thanks

[@patrickholt8508]

Thank you for the lesson very helpful..

[@ThePaintPaperHustle]

You’re welcome buddy

[@philbetthauser9547]

The air duct looks great, the paint job is killer. Did you notice any difference in charge temperatures?

[@ThePaintPaperHustle]

Honestly didn’t get in enough passes to notices. Only got one good pass in Saturday

[@donaldhaire1502]

Looks good

[@ThePaintPaperHustle]

Thanks buddy

[@tzed2509]

Carpenter tip: buy a cheap compass (the drawing circles kind) and set that to your flange width. Then you can trace the outline perfectly.

[@ThePaintPaperHustle]

Great idea

[@danielrita9663]

U have new idea for the pipe in-between that hood and procharger or keeping the one thats notched to clearance the frame bar

[@ThePaintPaperHustle]

No more pipe at all on the procharger

[@danielrita9663]

O.. it's going to be open now ...interesting wonder if it gains hard to say cause of all the new changes u made...u going to have tkm set u a new tune up for new pulley

[@ThePaintPaperHustle]

Yes I think it’ll be going back to tkm

[@danielrita9663]

I don't blame u on that thats a lot off money in the motor for something that can be prevented like a safe base tune lol its like buying another vowel to finish a phrase the more info u get the better ull get the closer ull be to making any changes to the motor setup and setting the tune urself..

[@no-centsfabshop9802]

Are you adding an airbox to direct air to blower inlet?

[@ThePaintPaperHustle]

I am not. We don’t want to restrict the air in any way. Just want it to suck in whatever is in front of the inlet

[@donald-1463]

Can you use two of them for cemtrical on the car

[@ThePaintPaperHustle]

You could if you want to.

[@funfun8095]

That's what I suggested, to make it look symmetrical.

[@newheart1109]

Hey Courtney. I have been meaning to ask were you got your wide mirror that you have in your car? Thanks.

[@ThePaintPaperHustle]

Off eBay. They also can be found on Amazon

[@danieltenorio3559]

Would this work for a heat extractor vent (as in putting it in reverse; placing it after radiator for heat can escape )?

[@ThePaintPaperHustle]

Absolutely

[@danieltenorio3559]

Yeah the metal frame under the hood I have to cut it a bit , do u think it would affect the strength of my hood ?

[@ThePaintPaperHustle]

@danieltenorio3559 no

[@lettuce9612]

Can you add a link to the part? How sturdy does it feel?

[@ThePaintPaperHustle]

Extremely sturdy. The links are always changing since they are eBay items. Search eBay for Naca Duct and you’ll get a lot of results. Let me know if you can’t find any

[@onebads2kracing]

Sup brother, im thinking about doing this my self, how much of a inlet Temp difference did you see or can you tell it’s breathing alot better with fresh air?

[@ThePaintPaperHustle]

Unfortunately we never had a way to measure any of that and didn’t run it long enough to be able to notice. We were always battling other issues

[@donald-1463]

👍

[@ThePaintPaperHustle]

💪🏻

[@donald-1463]

I was in the process of modification of your car just saying looking for a way to hook two up on your hotrod

[@gabriel1555]

Wrong place... There don't take any air flow, is in a lower pressure zone, you need move it back at possible closer windscreen

[@ThePaintPaperHustle]

Thanks

[@disciple77rc]

Have you researched naca ducts? They are designed to take air while being flush. That is why they were designed for airplanes. 0 drag yet still create hi psi zone and flow

[@Bob-ux8sn]

👍

[@ThePaintPaperHustle]

💪🏻