4.10 Gears: The ULTIMATE Gearing Ratio For Your MUSTANG

[@tjhessmon4327]

In the racing industry, we coin two phrases, Tall Gears and Short Gears. Tall Gears are those with what we call long legs, they allow the vehicle to reach maximum speed on a long racetrack, such as Charlotte Motor Speedway or Road Atlanta..... Short gears are those with short legs, they are used in events where the vehicle needs to accelerate rapidly but rarely reaches top speed or anything greater than 3rd gear. These "Short Gears" are usually confined to rally events, hill climbs, and autocross events.... Short gears (such as the 4:10) will allow quick acceleration, which might be effective coming out of the hole, but they will suffer greatly on top end as the vehicle reaches it potential redline RPM too quickly and therefore never reaches the maximum potential speed of the vehicle....... Compare that to a ...say 2:90 gear which will not be as fast off the line, however it will allow the vehicle to reach much faster speeds as the final ration of Engine RPM to axel turns is vastly reduced compared to the 4:10, allowing the vehicle to have much "longer legs" (aka lasts longer) and therefore achieve much higher speeds than the short legged 4:10 gearing....... A 4:10 differential at 7k RPM, produces about 25% to 30% less top end speed than a vehicle with a 2:90 differential (given all other things are equal)..... That said, it becomes necessary to understand what the car is going to be used for, in order to understand its relative rear gear setup. Try using a 4:10 gear at Charlotte motor speedway, and you will be the slowest vehicle on the track. If however you are in a autocross where you car will not exceed 35 mph, then the 4:10 gear will shine in that scenario as it will achieve those lower speeds quicker than a long legged gear ( such as a 2:90). Using a 4:10 gear in a street car, will eat a hole in your pocket fuel mileage wise..... further it will cause your engine to operate at a higher RPM, which results in top end cylinder wear over time...... The more ideal approach is to keep your gearing 3:31 or 3:55 and rotate your tire size, This will in effect allow one to change their final gearing without permanently swapping their ring and pinion setup........ Do the math related to tire size and differential gearing, knowing that smaller tires turn faster....

[@thomasmarquez6790]

4.10s are fine, especially if you plan to remain naturally aspirated. If you plan to add forced induction later, 3.73s would be my choice.

[@NateRider]

Very true! Adding boost you will want to get lower gear ratios. Good looking out

[@godsaveamerica2611]

3.31s, all the cars making killer times have 3.31s, 3.73 is still too aggressive, you'll still melt your tires and lack that top end speed.

[@bradbohen2615]

I have supercharged 5.4 with stock 3:73, I'm going to 4:11. But I have 9.75 not 8.8

[@lynnchello7231]

I disagree. With a boosted 6 sp manual I had 3.55 and 20in tires. I was in each gear forever. Went to 4.09. Coyote engines are a high reving engine.

[@WONDERBREAD89]

im boosted and want to run 410s with the Detroit rocker cams supercharger grind and shud be jus fine. least i hope lol

[@supertrooper2661]

Great video. Going to be installing a pair of 4.10 gears on my Crown Victoria after watching this. Was originally going to select 3.73 but the moment I heard, "Go big or go home!", my mind was set! These gears will compliment the full exhaust I already have installed really well. Stay tuned on the project, I have a few videos already! Keep up the great videos Nate!

[@NateRider]

I am so happy that I was able to help. That is what I am here for. 4.10's are the way to go!

[@hotrodlincoln7186]

I was thinking the same thing. I have a 2006 lincoln town car. I have a jmod done and 2 1/2 inch piping from the cats going into a X pipe then out to a roush axle back exhaust. Also, 1 big thing that helps ALOT IS the jms pedalmax. That eliminated the drive by wire. When I first saw the reviews on KZbin I thought they were just over exaggerating.. but it's the best 250 bucks I spent on the car. Quick question 🤔 wht would you think would be better. A procharger or a edelbrock stage 1 supercharger? I was originally thinking the procharger but, ever race I see on KZbin procharger gets smoked by the twin screw supercharger. Any thoughts?

[@msm402]

Enjoyed this! Have a 60,000 mile one owner 2006 s197.Added a Roush CAI and Extreme axle backs,and a Barton shifter as of now.These cars are crying for better rear gears,it seems to me.My Boss 302's and my Boss 351 years ago all had 3.91's in them,and to me that is the perfect street setup.I was away from this until last year when i retired,and i see that Ford doesn't make a 3.91 gear set,and the 390 gears available people say tend to whine.So,i guess it's going to be the 410's.Another thing i found out is that if you go higher than 3.73,you lose your cruise control.Mods for this year will hopefully be Detroit Rockers,and gears,with headers and mid pipe slated for next year...I hope!lol Thanks again,sir!!

[@NateRider]

I am so glad you enjoyed my videos! and yes 4.10's will be the answer for you! and you are lucky for cruise control because I don't have that on my mustang lol but hopefully you find the answer with those other upgrades haha good luck with your build!

[@jash3023]

When running these gears is your car screaming at freeway speeds, like 80 mph?

[@xxxxxxxx183]

Yea but who cares? Don't be scared of rpms

[@DumbldorWizzard]

@@xxxxxxxx183puts more wear on the engine and burns through gas

[@peterw2714]

Having this car with 4.10 gears in the rear end, I’m doing about three grand plus or minus at 80 miles an hour on the freeway in fifth gear.

[@highway955]

@@DumbldorWizzard yes if youre sustaining them for 10 minutes at at time. pulling 3500k for a few seconds hurt nothing. cruise at 55mph and you'll be fine. the real run is to be had on the streets. if you like to speed on freeway, lower gears wont be for you.

[@codymartinblack]

That’s crazy this is actually the next performance mod I was looking into doing for my s550, that and long tube headers

[@lc7192]

Actually the 3:31 rear differential gears are stock for the S197 Mustang GT. A lot of dealers ordered the 3:55 gears for the best balance in power and miles per gallon and that is where people mistakenly say that the 3:55 gears are stock, I have 3:55 gears in my 2007 Mustang GT and regularly get 25-26 on the highway and 16 mpg in town, I live at 4,500 ft in altitude so the 3:55 gears are primo. I would only consider changing to the 3:73 gears because I’m getting ready to order the Roush supercharger.

[@fabelgamer7410]

2005 and 2006 stock gear was 3.55,in 2007 ford made the 3.31 gears it'sdefault option.

[@maxhax-xb7ue]

I don't think you understand how excited you just got me, I didn't know there was 4.10 I thought there was only 3.73

[@ronierjones]

Always was confused about gear ratios. Thanks for the lesson!

[@NateRider]

That's why I am here! I'm glad I can bring that knowledge to you. I feel like a teacher now haahaha

[@johnbaker3843]

I put 4:10s in my 02 GT and couldn't really tell a difference. And it had 3.27s stock. I'm thinking they never swapped the ring and pinion. It still tachs the same. Thinking I got ripped off

[@1456941]

There is no thinking to it, you was absolutely ripped off. Going from 3:27 to 4:10s is a big difference and you would be able to tell right away. There is NO WAY possible for 4:10s to feel like your 3:37s

[@lancebrown2421]

I read 4.10 plus gears are recommended for the auto 10 speed. I currently have a 2020 S550 base with 3.15 gears. I hate the pull. It lacks. I have Nitto 555 G2. 285x35xr20 rear 255 front. Can't wait to upgrade.

[@Jpizzle925]

your vids are always awesome... keep up the great work.. love seeing your car it's set up nice can't wait to see some Dyno numbers

[@NateRider]

Thank you so much! I really appreciate it :) Yeah I will definitely dyno and show you all the numbers very soon

[@boostedart88]

Good video 👊 I got a 06 GT ,Saleen supercharged stock pulley 7.5 psi ,stock saleen intake ,cerviny side exhaust ,& 4:10 gears aswell just that on low boost puts out 450whp & 500+ crank I really recommend boost easy 150+ hp gain I will do pistons rods and turbo swap or maybe compound boost for a little it should be fun 😈 go for it boost !! 💪🐌

[@NateRider]

damn you are going all out haha thats gonna be a 10 second car right there!

[@Sick_ridz]

17 Mustang GTCS 6R80 trans. It came with 3:55 rear end and it has ford performance pack 2 on it with Borla Atak catback. Don’t know how much power it make but it will pull on my brothers 17 2SS with headers and cai and is almost dead even with a stock 17 C7 from a roll. Thinking of doing 3:73 gears and headers next

[@thomasgilroy6187]

Well gears really only help if you’re lacking real hp/tq ! I’ve got a 03 Cobra and even with the 3.55 gears and 335 nittos on the back it’s a challenge to keep them from spinning the first 3 gears

[@brandonmantle9719]

Your ‘08 is beautiful and she sounds amazing. If I can get my hands on an early 5th gen, I’m gonna build it to look like yours!

[@conspiritor1]

Love your work man! I got the 3.73 gears in my AM cart right now along with a Bama Performance tune. BBK cold air intake, Steeda Throttle Body, Screamin demon distributor, Taylor Wires, NGK iridium plugs, and Flowmaster American Thunder Muffler. Hope to get mine to Sally's level one day!

[@NateRider]

What numbers are you making? Have you dyno yet? Aye those mods sounds like a great setup for any mustangs. I used to have the flowmaster american thunder and boy did I love them so much!!!

[@conspiritor1]

Nate Rider I have not done a dyno yet, looking too soon for sure. Definitely would like to add some more mods before strapping her down. Yea dude! the flowmasters sound so nasty! But those Borla's, Nate, damn they sound beautiful!

[@NateRider]

Sweet let me know when you do! Yo I know! I am in love with flowmaster and Borla sounds. It is magestic

[@conspiritor1]

Nate Rider For real, man! Mustangs just sound glorious with the right pipes. Id love to cruise out to Cali and see Sally in person, let alone hear her! Tough when I'm all the way in CT. hope I get the chance.

[@NateRider]

I might be doing a meet and greet soon. So stay tuned for that. I would love to meet my subscribers!

[@Tracks80]

I pretty much had the same mods you do now before I upgraded my cams and intake. Before and even now I have found the best mod you can do is not your tires next but swap out your LCA and UCA. I went with steeda LCA non adjustable with the two different bushings and I went with the steeda UCA adjustable and it made a world of difference keeping things planted with 4.10s and your mods.

[@NateRider]

I actually just got some BRM LVA and UCA! They are coming in the mail soon. stay tuned for the video!

[@anthonybarclay2537]

Hey bro did the 4.10's make the clutch feel a little more touchy! My car stock is sometimes hard not to jerk around a little bit.

[@NateRider]

I did not notice any difference in the clutch. You should be fine

[@andrewparker4350]

I have a 94 GT, which is a 302 5.0, I have 170 Twisted wedge heads, 24 lbs injectors, calibrated MAF, T MOSS ported intake, and a simple E CAM. I believe with a tune i should be around 290-310 hp with around 320tq. at wheels. I only have the weak 2.73s car feels very slow. I have 4.10gears ready for install what can I expect?

[@zachary6324]

414 whp. 3.73 gears. Roush CAI. tuned by Levin Motorsports. 2015 GT

[@mrwookix5324]

Sweet. Im going with 3:73's. I had a 92 Stroker on 3:73's just got Babyblu (2007 s197) Pypes H-pipe. gonna do the install myself. Love the vids.

[@codyfox9596]

ya the 3.73 will help with traction beeter than the 4.10 if you plan on making more power in the end

[@mrwookix5324]

by boy has 4.10 in a Cobra and MAN what an amazing feeling

[@NateRider]

Aye 3.73 aren't bad at all! They are amazing too. I hope you install it the right way. I wish I knew how to install gears like you lol

[@NateRider]

Yeah imma need to do some upgrades on my suspension next lol

[@NateRider]

Receipt for domination right there! haha

[@mattbritton8976]

I should be buying an 08 v8 gt/cs mustang soon. Just found your channel the other day and I got hooked so I subscribed. Can’t wait to start modding my car, and down here in Florida we don’t have to worry about emissions.

[@NateRider]

thanks for the sub man it means a lot to me and congrats on your new ride when you get it! You will love the cali edition i promise

[@amc703]

Have 4.10s sitting on the bench bolted to the spool about to put them in once I get the housing painted ... but I might be putting 4.56s in

[@NateRider]

Danm you going really big! lol you race on the strip?

[@amc703]

Nate Rider yeah it's not my daily driver anymore so it's more of a weekend car and track car

[@n1ghtfury4.6GT]

When I Eventually Get My 3Valve 05-09 GT definitely gonna have this mod 4.10 gears thats a fact.

[@spaomalley]

Without blower I see gears ranging up to 5.71...a lot of reviews for 4.10’s but I read 4.30 is even better but 4.56 and above being too much. I don’t race but I want a powerful feeling in my street car. 4.10 or 4.30 and why?

[@jcutt2718]

i love having the 4:10 gears. all the civic and 350z owners at my job cant touch my mustang on the road. i got the screaming yellow 2006 gt with comp cam mutha thumpers, brute force cai, hurst shifter, bama tuned, ford racing throttle body, and pypes x off road and tips. check out my video on my stang and lemme know what ya think. i love ur mustang!

[@donnie6178]

Have 4:30's on my 3.7 there crazy fast, I put 10"tires and i still cant them to hook up even at half throttle.

[@aimless-drifter]

6:33 it's 2022 and I bought 2012 Mustang V6 because it has good fuel efficiency :P (and because it's fun to mod)

[@biggrime]

are you concerned about drive shaft with 4:10 gears?

[@NateRider]

Not at all! But if it breaks I will sure let you know! 4.10 gears are so great

[@biggrime]

I hope not that would be bad. I got 4:10 on my 2013 3.7 drive shaft is known for breaking past like 125 mph on stock gears. On 4:10 I wouldn't go past 90 mph

[@NateRider]

Ohh yeah idk bout the 3.7 driveshaft. I haven't done research on that. For 05-09 mustang's you should be able to go top speeds with 4.10 gears with no problem. I have gone 140 with the 4.10 gears on and Sally took it like a man

[@biggrime]

Nate Rider that's sweet!

[@Djuane]

Nate Rider so you hit top speed with 4.10's??? if i remember correctly this style had the 140 spedometer.

[@streetcarmedia660]

I have a 05 Legend Lime GT, current mods are: JLT CAI, Summit Racing Springs, Gt500 strut mounts, pypes off road x pipe with pypes mid muffler catback. Also have a bama 93 race tune and to make the shifts better I have a hurst competition plus shifter installed. Currently not dynoed yet. Currently have 3.55 gear. I would love to go 4.10s

[@NateRider]

You should name your mustang the DEMOLISHER because that's what it sounds like just reading what you got on your car. SO SICK!!! I really wanna get that short throw shifter. I love HURST so much

[@streetcarmedia660]

Trust me dude you will like that hurst. Cams, and headers are also on the list. You have a sweet ride man.

[@NateRider]

A lot of people say its notchy? Would you agree? I think I would still like it either ways. Thanks man I appreciate it :)

[@streetcarmedia660]

it's notchy buy i I love it :)

[@NateRider]

Fasho! I'm pretty sure I will like it to. Stay tuned for that short throw coming soon!

[@smokky3v]

So what would be better for roll racing in an automatic 2014 gt

[@bennryan2]

are 1st and 2nd gear a waste now? i have currently have the 'unresponsive' 3.55s. thanks!

[@mattsmith592]

I've always been iffy on a 4.10 gear upgrade, but your video is really convincing me to get some 👀

[@NateRider]

I would go with 4.10's if I were you. They have so many good reviews with people that have them

[@2011italianoboy]

Love the video kid. For the tire selection, I have Nitto NT555, 275/40ZR18 103W, on all four corners. I've used them at the track and gripped pretty good. Here in NY, I don't drive my car in the snow and from sitting in the garage, I don't have dry rot, or flat spots on them. Had them for 4 years and they still look good. Not sure what kind of gears I'll go with. I've thought about 3.73, but also 3.90. Has anyone else used 3.90's?

[@NateRider]

thanks man I appreciate it. I love the Nitto tires as well. I may slap them on in the future. and nno I haven't done any research on the 3.90

[@darkness0621]

I ran 18x9 on front and 18x10 on rear in my 08 gt with 4.10s and gt500 rear dif, hooked up well.

[@NateRider]

Yeah I want to go with a staggard setup myself. I hope to have the same setup as you

[@TheSunofhell]

Followers from Switzerland and I love your video. Thank you for all your advice please never stop ;-) Sally is awesome!

[@NateRider]

Damn all the way across the world! That is so cool to see my subscribers and where they are from. I shall never stop! Thanks for the support

[@sierra5713]

How do you know English if you're from Switzerland?

[@calebclovis9035]

Hey, I daily a 2008 v6 mustang with a K/N CAI and aftermarket exhaust with a 93 Bama Tune... do you still recommend 4.10 or 3.73 gears?

[@cljerjr31]

315 35 17 tires on 17x10 wheels would be great

[@MrRanggong]

Nice job on this video editing. Very watchable.

[@jordanguillory6864]

06 3v checking in. Cali laws suck man. They hate my car and my guns. Car looks good bro. Well, here is the list. JLT CAI. JBA longtubes and O/R H. Flowmaster outlaw axlebacks. Dyno tuned @ 300 Wheel. MGW shifter. Braided stainless lines with Xtreme stop pads and slotted drilled rotors. Gt500 front LCA . Full BMR rear Suspension. FPRP K springs on Koni strt With Gt500 strut mounts. Exedy Mach 400 clutch and flywheel going in this week. And a grip of cosmetic stuff. keep up the vids man!

[@NateRider]

Yeah you can say that again! SWEET! That set-up sounds sick. I definitely loving the long tube headers. How are you able to have long tubes on cali?

[@jordanguillory6864]

Im in Texas. just saying the stuff i enjoy is a no go out there. i want gears but im debating on NA or FI. 3.55 would be perfect if i go FI. we all wanna see a couple of Passes When You get the dope hooked up bro!

[@NateRider]

Yeah if you have all that power, then smaller gears will work good for you. Thanks my man will do!

[@creepystank420]

Getting my 4.10 gears installed today on my 03 mustang GT vert

[@LegionFitness52]

I have black staggered fr500s 18x9 18x10 wrapped in HTRZs...love them and would look good on yours too...plus not many have fr500s...i have SR UDPS, Diablo 91 tune, UPR Off road xpipe, Hurst comp shifter, BBK CAI, PORTED POLISHED THROTTLE BODY and 4.10s on a shelf lol

[@NateRider]

I really want to go with the staggard style on my next setup. I thin it would look super sick! I will look those wheels! Thanks for the suggestion :) haha you needa put those 4.10's in! What is you doin?? lol I was wondering where you left off to. I haven't seen you in a while

[@LegionFitness52]

Nate Rider lol just busy man, work work work lol and also catching up with subscribers

[@NateRider]

I feel you! Gotta get that mula! don't stop grindin lol hope you install it soon

[@tidytraphouse2801]

Can you please tell me how much they charged for labor just got my 4.10 for my 2v and I can't find less than 600 online people say shouldn't cost more than 400 and I think you should go gt500 reps or any multispoke compliments s197 imo

[@NateRider]

you should expect to pay anywhere between $300-$500 for the install. You just have to call around and get the best price

[@PHIATEHALO3]

I’m in San Diego what mechanic did you use?

[@newfie-dean5803]

It does not appear that you have modded to a one piece aluminum drive shaft yet? This is an easy install that you can do yourself. The stock 2 piece steel shaft is over 40lbs. The one piece aluminum is like 20lbs so you have less rotating mass which transfers the power to your wheels faster. With the aluminum shaft you will increase acceleration times and especially coupled with the 4.10 gears. Research the aluminum shaft. I highly recommend that mod. Also, the aluminum shaft is stronger than the steel shaft. You also don't have to worry about having the carrier bearing failing, a notorious issue for 2-piece driveshafts.

[@NateRider]

Oh trust me I have been wanting the one piece drive shaft for the longest time lol but the price isn't too appealing to me. Imma have to save up for that one lol thanks for the advice tho imma do more research on it

[@jamesscherbenske9354]

@@NateRider dude I don't understand I have a 2001 Mercury Grand Marquis

[@blueridgekicks3962]

I thought stock was 3:31 ? Which one is it 3:55 or 3:31 ?

[@trojannatiom]

I have late model restoration SVE drift wheels gloss black. 19s by 9.5 all around, and nitto NT555 G2 285/35-19. Looks are good, but let me tell you, performance is superb. 2007 mustang GT procharged. Good luck

[@NateRider]

WOW! You stang sounds like a BEAST! What a setup! Imma have to look up those gloss wheels! Thanks for the suggestions

[@aggregor5431]

Hey Nate Rider. What are the top speeds for each of your gears. I have an 08 GT with the 5spd but It may already had some stuff done to it when I bought it. My speeds are 1st-35, 2nd-62, 3rd-85, 4th-115, 5th-150+. I am just trying to figure out what I really have in there.

[@NateRider]

I really wish I can tell you my numbers, but I cannot say exact. I am hoping to dyno my car very soon to show you guys all the numbers that sally is pushing. Sorry! But stay tuned for that next video!

[@aggregor5431]

Nate Rider I still gotta get mine dynoed as well, but before that I still have to get my cams and longtubes put in. I bought the comp cams nsr stage 2 xfi if you're familiar with those. And with those 4.10s you got great acceleration but the only trade off it kills your top end. What I mean by that is that long 5th gear is going to kick in a lot sooner. You should make an acceleration video as well.

[@bloodsurf69]

4:10 might be to low if you're running a 3 speed auto. What's the ratio output of the transmission? O.D.?

[@NateRider]

i have no clue lol sorry bout that

[@davidboyd3670]

nice and nice car as I have a black 2007 ford mustang gt and have a 62mm throttle body and the same cold air intake as yours plus a 92 octane race tune from bama tunes as it pulls. I want to get the 4 10 gears next then the muther thumper cams then the long tube headers and cross pipes as my budget is limited and time it will take me but I love the difference so far

[@NateRider]

haha yeah its always tough choosing parts when they all cost so much plus a lot to install too. Make sure you grab the 4.10's tho! You will love them

[@sixxfan]

I see your SDSU bag at 1:55. I went there.

[@bbj5958]

Is this also usefull with the 2017 V6? Other advices for that version. I don't drive that fast but when i start i need to go. Thanks

[@NateRider]

I would recommend 3.73 for your type of mustang! That will make a huge difference

[@bmlaabul]

Amr wheels 19 inches, as for tire 275 at the rear and 245 for the front and you should consider long tubes as we'llwe'll

[@NateRider]

Thanks for the suggestions! I will look into those AMR. I know a lot of people love them. haha I wish I can get long tubes. Maybe after I pass my emissions then I will slap those babies on

[@dillbill2A]

I'll take your rims and tires! Lol I think those MAKE that iconic muscle car look.

[@NateRider]

Hahaha it'll be so hard to say bye to these wheels. They are definitely one of my favorites

[@mattparks11]

2:20 rims and wheels are the same thing buddy

[@NateRider]

rims + tires = wheels!

[@deecee4644]

No...haha rims + tires = rims and tires. Wheels and rims are the same thing.

[@dogsay1078]

The correct word is wheels. Rim is the outersurface like a basketball rim.

[@deecee4644]

Not. No one I ever hung with said hey man, let' check out those cool outer surfaces you got. Idiot.

[@dogsay1078]

DEE CEE companies don't call it Racing "Rims" for a reason. TRY AGAIN BUD

[@ManofSteel4God]

Hey Nate Rider great video explaining gears, 4.10s are definitely on my list next. This weekend I installed my O/R H Pipe from Pypes and man does it sound amazing with the flow master axleback I already had on. I also put on a GT500 spoiler. I had a question though...when it comes to emissions I was planning on just throwing back on my stock h pipe to pass test then putting my O/R one again, what do you recommend ?

[@NateRider]

beautiful setup! I love what you have done to your mustang so far. Keep it up. And yes, that is what I always do for emissions. I just swap it right out and as soon as I get the pass I go right under to change back to my off road H pipe lol

[@ManofSteel4God]

Awesome man, you're a cool guy keep up with the videos😎 What short shifter do you got? I was thinking of a mgw, I have heard great things of them.

[@NateRider]

I don't have a short shifter... but I would go with Hurst shifter if I ever get one. Go check that out

[@The_HolySpirit_5.0]

Can you swap from the original factory gears to 410 gears with a 2007 Ford Mustang V6? If you can is it true that swapping out to 410 will allow you to spin both tires instead of just one??

[@hmuvee]

does the under drive pulleys really make a difference

[@sidewaysjorah10]

david green yea think the same thing. i want to know

[@hmuvee]

👀

[@NateRider]

Minimal to none. It is a performance mod you put on to squeeze ever last Horsepower out of your car. Its easy to install and it is not that expensive (I actually got mine for free), that's why I have them installed. On American Muscle they do claim that it gains Horsepower

[@NateRider]

I hope that solves your question! Let me know if I should do a short video on it

[@sidewaysjorah10]

Nate Rider yea that helped didnt know if it did much and i was going to buy it off american muscle. thanks for saving me money cause i was expexting 10hp gain as am says

[@thmqpgap]

Hey so I’m thinking about getting these, is the acceleration difference between stock and 4.10 really noticeable or just meh noticeable?

[@timtresch4848]

I know this is an old comment but trust me I've been in the mustang world for years and years, gears especially for an automatic is by far the best value mod you get besides maybe a tune. Just make sure you get it done it done at a good shop for a fair price and assuming it's a mustang make sure you use the Ford racing gears so it doesn't cause hear whine. Honestly gears, are going to have the best performance increase from anything except for Super/Turbo chargers or Nitrous nothing else will compare, still a great bang for the buck even with the mpg hit if you daily your mustang

[@thmqpgap]

@@timtresch4848 right on appreciate the comment👍 still have my 3v but haven’t done any gears due to it being my daily and commuting on the highway mainly

[@ottobauch2179]

Hey check out advanti racing Traktion or some rovos Durbans, I'm rocking the advanti but I love the rovos as well!

[@NateRider]

Fasho! I sure will. Thank you for the suggestions :)

[@hmuvee]

what does your s197 top at now... mines need a tune up and stock besides manga flow after stock hipe... and mines top out around 136 for now

[@NateRider]

Whatcha mean top out? Like top speed? I am not sure the numbers. I wish I did tho. Hopefully I can find out and let you guys know exactly what those numbers are

[@thundarwabbit5140]

Nate, really appreciate the vids, starting going through them, I would like to know if you have a vid on simple bolt on powermods for a 05, 4.6 GT. I think I got the suspension most parts Koni shocks and SR-1 Kits and all that jazz. if you can let me know your thoughts or what videos i should search for. Thanks again bro. keep'em coming!

[@NateRider]

Are you reading my mind or are you a time traveler cause you are digging into my list of videos to come. Just wait on it ;)

[@thundarwabbit5140]

Rgr that, I use to roll out of El Cajon and Spring Valley Yo! I'll be waiting Peace out!

[@fastguned]

You said the only bad side is the gas mileage but there is more wear and tear on the motor since it is spinning more revolutions per mile.

[@iversonalcerro6765]

Hey what’s up homie, damn first time seeing your videos, this gears video was fire 😮‍💨 understood everything, By the way I have a question, what would be better for a v6 2012, the 4.10 or 3.73 because my v6 is now running 2.73 gears stock

[@catlincardona8008]

What did you use for the white letters on your tires. I want to do that to my 96 gt

[@salvador-z4213]

You deserve more subscribers!

[@NateRider]

Thank you so much! That really does mean a lot to me :)

[@skyshover2983]

How much winding sound did u get with the 4:10 gear swap?

[@JackwDyles-zu3jt]

I've got two Mustangs. A 94 LX with a 429cj and C6 trans and I run the 3.73 gear in it and it does great. And I also have a 2000 GT that has a 5 speed and a little tune up and 3.90 gear in it and it does great. Have no problem getting from point A to point B . Do not like the 4.10 gear. Had no luck with that gear.

[@YkShotti]

Great video bro I just got a 2001 mustang Gt I was debating on 3.73 or 4.10 ima go with 4.10 fuck it lol

[@bigdgreene2677]

Did you put the 4.10 on yet if so are they any good?

[@christopherhetterich6161]

Good vid. You did a good job explaining everything!

[@NateRider]

I gotchu Chris! Thanks for the feedback

[@thetbear69]

Now I know you have seen my wheels,they are the Boss 338s,they are 20s staggered 8.5 255/35/20s on the front and 10 275/35/20s on the rear inow I am still running the stock 3.55 gears

[@NateRider]

Your wheels look sick! I love them so much. I wish i had them lol niceee you needa upgrade your gear ratio!

[@thetbear69]

I've been thinking about it,but mot sure if I want to go 4:10s but maybe 3:73s

[@NateRider]

I suggest the 4.10. It pulls like no other!! Trust me, Plus look at all of the other reviews on American muscle.

[@thetbear69]

Well will see,got to have the money 1st lol

[@RoryEditsOfficial]

Got that stock basic bitch 2017 s550 v6, about to do roush cai and axle backs, came stock with that 3.13 gears, do a 5.4 0-60 havent hit a dyno yet

[@godsaveamerica2611]

You should think long term. With forced induction, you want the lower rear gear ratio for traction and you get top speed to compete with the big dogs. 4:10 with a blower means melted tires and no top end. And you'll want a blower!

[@NateRider]

yeah i only got 4.10's cause I don' plan on boosting it any time soon cause i don't have the money lol but if i ever do, ill probably go to 3.73

[@transporter83]

Can you comment on what head lights you have on Sally?

[@NateRider]

They are the reaxiom DRL projector headlights. I got them at americanmuscle.com. I also posted a review, unboxing, and installation video on my channel. Go check it out!

[@mustangmarty8491]

Thanks for sharing, I was wondering either 3,73 or 4.10 I have a 88 GT mustang 5 sod. So I didn't know about top speed on the highway. Anyway Thanks brother.

[@jamesw576]

Mustang Marty I have an 89 GT so let me know what gear you chose, I’m debating 3.73 and 4.10

[@brandonrickbornponyexpress6574]

What did yall decide on the fox? I'm getting 4.10 on my 89 5 speed

[@VASAMOAN]

Nice move getting the gears! What camera and mic set up are you rocking?

[@NateRider]

Right now I have the DJI Osmo and the Rode microphone!

[@brandoncollins6621]

black bullitt motosport wheels...got them on my 07GT..best wheels for the 05-09 S197's

[@NateRider]

Sweet! Thank you so much! I will check those bad boys out!

[@HeavyMetalCamaro]

Where in Cali are you from? I’m in LA. I’m getting 4-10’s on my SN95 very soon. Probably within the next week.

[@100thomasmagnum]

Did you notice much change on your speedometer? Also, you got a JLT CAI. Ive been in the market for a CAI. How was the fit on your 2008? Did you get the Bama tune with it? I am debating it. I was thinking Airaid synthaflow CAI. Opinions? i am a little afraid of premature wear but need a cheap pwr pick up. Nice vid again!

[@CLPATTERSON]

James I am currently selling my JLT CAI and tuner. I ordered an Edelbrock E-Force supercharger and no longer need it let me know if you are interested.

[@100thomasmagnum]

CLPATTERSON hello. thx 4 offer. but I am in market for new one with custom tune. trying to put only new stuff in my Stang as its got 123K miles on it now. yikes!

[@CLPATTERSON]

No problem I totally understand, FYI In the tuner is a custom dyno tune for the JLT it cost me like $400 just for the tune and it made like 14hp and 20 pounds tq over the can tune that came with it from Excessive motor sports.

[@NateRider]

I LOVE the JLT Cai so much!!! JLT and AIRAID are the best cai you can get for your mustang. No matter which one you get, you will get the best performance out of it. It is a tie for me for both. Go with your heart. You will not regret either one of these great cai

[@derekjohnson5174]

Lol you don't gain 40 hp with a hot air intake, catless h-pipe, and straight thru mufflers. You can't believe everything americanmuscle tells you, trust me I've been there before.

[@Blazerghost]

You might see like 15-20 hp with those upgrades but that's it, AM is a bunch of lying diptwads. If you throw a comp cam and throttle body and intake, then you'll see a 40+ hp gain

[@plazmamasta193]

BlazerMountain I think with a tune you would see those numbers but without one I doubt it

[@czarmarti]

I live in southern cali, which shop did yor 4.10 dif gears.

[@legendaryrj_5908]

Do you need the whole kit to install the gears because I bought gears but not the whole kit from summit racing.

[@gearhead6424]

Top speed is only lost because of the lack of gear to RPM. And MPG usually isn't affected that bad unless you forgot to calibrate your speedo to match the new differential ratio

[@Puma99S197]

Like why nos if you dont have the internals to handle the nos ...... save for a blower man

[@NateRider]

It will be years till I get the blower lol Nitrous is so cheap and so easy to install, so I went with that. Imma build Sally so she can handle anything

[@Puma99S197]

Nate Rider cool gotcha ma just please dont blow it up thou ..

[@MaxedOutPlayet]

Josh badaxe nitrous is pretty safe they usually come with a device so like if it backfires it shuts of the nitrous complety

[@NateRider]

haha I'll try not to!

[@NateRider]

Yes especially the one I got, the Zex Wet Nitrous. I got all of the safety add ons that I could get as well for this kit

[@Malboeuf1993]

I just got 4.10 for my mustang gt. I haven't installed them yet. What's the traction Difference between stock and 4.10? Should I get a good set of tires? I also do alot of highway driving.

[@NateRider]

traction is the same, but if you boost your car then you will need it. Highway mpg I get about 18mpg

[@Malboeuf1993]

Nate Rider right now I get about 20 mpg highway. 18 is not to bad for a v8. Idk if I will ever boost my mustang anytime soon, its very expensive. Thanks for the response.

[@maxhax-xb7ue]

Nice video btw!

[@Agent.K.]

Great video and easy to understand!

[@NateRider]

I am glad you liked my video :)

[@skullcrusher58]

hey man if you got friends or family that lives in a state that doesn't have emissions testing have your car registered to their address & you will not need to do emissions testing so you can do way more to your car legally

[@NateRider]

I just have family in Michigan. I needa see if they do emissions lol thanks !

[@Djuane]

those sr underdrive pulleys are a bad idea. most of the brands cannot keep the vibration down enough on the harmonic balancer and can blow your oil pump ive seen it happen. brands like steeda or other top brands specially make theirs to completly avoid that issue. thats the one thing i wont go cheap on.

[@NateRider]

Awesome info! I never thought of that. Thanks for sharing!

[@jamescorbett9538]

I went with the 373s and I have 20x10s on the back. My car still blows the tires. Getting the 410s installed now I’ll have it back by the weekend, I hope they help. Thanks for the video.

[@ericksanchez7787]

Wait wouldn't the 410 make it spin the tires even more?

[@johnpaniccia3802]

How did the 4.10s work out for you?

[@jamescorbett8791]

Just saw your message man my car works great but yes it will blow the tires off lol. I’m boosted now but before a average coyote with mild work done I’d blister them when I put my slicks on. I have videos to prove it. I love my gears even being boosted. If you’re on fb send me a friend request and I’ll show you some videos.

[@terrywalker9092]

Miss your videos on 3v mustangs. You were the guy on 3v mustangs. Just like Derek Baran is the 4v guy. Amazing he jumped from a 2v mustang to a 4 valve 2013 mustang. Now he's had a cobra 2004, but realized mot a market for the Terminator. Honestly it is the car he wanted. But so few, so nobody watching. Sold it quickly and bought a S550 automatic! I don't blame him. But it is not what he represented in the past. It was manual all the way. Now it's a 10 speed automatic It doesn't miss shifts and so much faster. He recently did a video on a 3v. Wasn't his car but something he recommended. Hmmm. Can recommended the car, but never owned one?

[@FPSNetwork]

Where did you get these installed? I've gotten quotes all around $500 for install only in socal

[@frankyluc08]

Get welds rts rims on Mickey Thompsons it's a kit for 1600

[@NateRider]

ss boy imma check those out! Thank you :)

[@JustinsSVT]

You should get the AMR gloss black rims, or the the MMD 551C's (5 Spoke) !

[@NateRider]

AMR's seem to be the hit in the comments! I will definitely check those babies out!

[@iridious6433]

I'm a highschool student an i live in a rural area, so school is 30 mins away. what gear is the best for mpg without killing the top speed?

[@FromNothinDGK]

Do u need the full kit or can u just go with the 4.10 gears without the whole set and still feel the same experience

[@Justafew4U]

Someday when i have $$$ , I'll get the 3.73 for my S550 gt.

[@NateRider]

go for it!

[@brandonlonvelin846]

Great videos by the way 👌

[@NateRider]

thanks brandon I really appreciate it

[@alexisramirez279]

Wondering if this stuff works on an automatic gt ? New to this stuff

[@lancebrown8823]

Me too. I emailed Steeda. He recommend with a 10 speed to stay stock which mine 3:15 gears. Add a tune plus cold air intake. That should wake it up. He said auto has too many gears and 1, 2, and 3rd would be useless with 4:10 gears. What ever that means.

[@forcedair92gt94]

That installed price wasn't bad $500-600. 4.30s on a DOHC motor is the ultimate, coupled with a T-56 that has a .50 6th gear.

[@joshlower1]

If you haven't upgraded to a limited slip differential, please do. You will thank me.

[@NateRider]

imma do that when I save up!

[@joshlower1]

Nate Rider hit me up on facebook and we'll talk lol. Friend me on facebook at Josh Lower