Thanks for the input. But it would be so nice to make a complementary circuit to this which allows to protect the pump when the system is without water.
@muniraja5317 Жыл бұрын
No
@welcome12345jan253 жыл бұрын
Very good effort and you wish to share others also. Thank you🙏🙏🙏🙏🌹🌹🌹🌹
@blup02123 жыл бұрын
Circuit update: I made this circuit by watching this video but there were two errors coming: problem 1: motor was off during the water level and turned on when water level touched all top position(red) wire. solution : don't connect the wire on nc terminal connect it on "NO" terminal problem 2: after the modification motor gets on when water goes just below top level (red) wire. solution : I exchanged blue wire with red wire and the circuit worked fine
@SajiVlogsSL4 жыл бұрын
what if some short circuit leaks the current through wire to the water ? is there any safety for that ? I dont think so right ?
@kabandajamir9844 Жыл бұрын
The world's best teacher thanks
@ashokghugare36514 жыл бұрын
Guys very IMPORTANT NOTE if your 100 omh is burning or getting crazy hot then try 10K resistor. It will work
@AnandaRajaT3 жыл бұрын
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively 🙏🙏🙏🙏 And whether ac or dc current to be supplied???
@muhammadaftab0773 жыл бұрын
Thank you sir bht khooob. Kia AC 220v 1HP ki moter use kr sakty hen is pe?
@chidiayoanasonye92433 жыл бұрын
Thanks but I have two questions : I used 9v battery and it drains easily what can I do . secondly my relay keep smoking when connected to my 1hp submersible pump what can I do . plz advice
@arnbon62414 жыл бұрын
Thanks for uploading this useful circuit. You're an awesome guy.
@TinyAbode3 жыл бұрын
Good work. I will try myself. I have to use it with 5V supply only since I have a 5V USB adaptor and a 5V relay module. What will need to be changed or modified in the circuit if using such a 5V relay module? I have another question: I wish to show an LED light up for 5% level. How to do this? Also, when the level is below 5%, how can I attach another LED to glow (indicating level below 5%) so that when the water reaches 5% level sensor, this LED (below 5%) stops glowing but the 5% LED starts glowing? Can I also use the 5% LED as a flashing one and how? Hoping to hear from you soon.
@parmardamodar64922 жыл бұрын
You can do it with a diode and a relay only ,
@AnandaRajaT3 жыл бұрын
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively 🙏🙏🙏🙏 And whether ac or dc current to be supplied???
@khan691 Жыл бұрын
Agar really or circuit ko 12 volt supply pr use krna ho to kia changing Karni Hogi?
@firewater3652 жыл бұрын
hi. i tried to do this using a breadboard and arduino uno for a class project. it was a fail! thanks for the video and i'll keep trying
@fabianmof30014 жыл бұрын
Please building the case ! Safety is number one prioryty ! ❤❤❤❤❤
@Ciiads4 жыл бұрын
👍
@eder120194 жыл бұрын
💯 Sensacional 👏👏👏👏👏 Gosto muito de eletrônica Parabéns você show 👍
@Madar3472 жыл бұрын
Hello, is it possible to make an electronic circuit for an inverted water pump? For example, the bucket will fill with rain and empty automatically
@JordanDias13 жыл бұрын
By inserting electrodes in water would there be any electrolysis effect?
@realvisionforever Жыл бұрын
Slightly
@subharghyamanna2 ай бұрын
Can I use the system for submersible also?
@vijayprakashnagllikeuandyo54203 жыл бұрын
Just one question current flow in tank outlet yes or no.please experience me and current flow in tank outlet which volts.
@goutamkrsah95113 жыл бұрын
No current flow as it is dc operated ac switching circuit
@royer27214 жыл бұрын
Muchísimas gracias , un saludo de Galicia , Vigo
@robertshortnacy89904 жыл бұрын
Just one question why do you only show the schematics for 2 seconds
@creativemindedbadal56524 жыл бұрын
Fantastic🤘😝🤘 bhai love ❤❤❤from odisha
@BJBVlogsOG Жыл бұрын
3:35 The thick wire is for AC 220v?
@nasrubinmohammed79174 жыл бұрын
Nice design- recommend for to add sensing foot valve level also along with this.. so this will become also safety for pumb motor.
@sainkyverma383511 ай бұрын
Sir same circuit 24 v dc relay main capisitor aur transitor kis no ke use krne h
@chidiayoanasonye92433 жыл бұрын
Good . But could you plz tell us what voltage you used to power the circuit. Can I use a 9v battery ?
@dalexplym4882 Жыл бұрын
It shows 6V to the left of pin 4. It should work on 9V, too -- but relay specs and battery life should be considered.
@oknemohcrapalain80353 жыл бұрын
Super. Simple et utile. Merci
@aurimarbraatz88033 жыл бұрын
boa tarde muito simples e bem bolado parabens mais seria interesante se dece de por 3 leds indicadores
@gk69934 жыл бұрын
Incredible. So many uses. Thanks
@vjshortfilms23003 жыл бұрын
I wanted this type video. everyone making this circuit using PCB. This video is best
@VIJAYKUMAR-dv9gp Жыл бұрын
Sir apne supply se kase jorte h wo nhi dikhaya
@rakeshkchauhan4 жыл бұрын
Instead of supply line, make ground line pin 1 common, interchange 2 & 6 and use pin 7 to operate relay
@babumon42843 жыл бұрын
Hi. Pls, where to connect dry run protection ? What are the modifications to do ?
@pjqazi96474 жыл бұрын
If I connect to the aquarium, will the fish swim belly up?
@heykeliglesias26394 жыл бұрын
🤣
@anshupatwal62052 жыл бұрын
How much power suppy give this circuit ?
@SocialForest-z4o11 ай бұрын
I made the circuit. But when the motor starts the base register of bc547 and 555 ic gets very hot. What to do ?????
@kangsunboxing73764 жыл бұрын
Where are you from india? I mean which state
@IdreesZaman-c1f Жыл бұрын
Circuit diagram at 1:33
@hobielektro Жыл бұрын
Mantap sahabat ku sukses selalu
@reidogarimpo16914 жыл бұрын
Great!!! Thank you my boy! João from Brazil!
@Ciiads4 жыл бұрын
Welcome
@saidtv27104 жыл бұрын
Can it to pump 220 volt?
@reidogarimpo16914 жыл бұрын
@@saidtv2710 Yes
@boka70boka4 жыл бұрын
Tank you. Nice. Im from Poland.
@foorwq78164 жыл бұрын
please tell me, how can this be used to control a 220V 1 horse power motor/pump...? what more is needed?
@heinrichgerber70603 жыл бұрын
Use the same relay, 10A 250VAC. 1hp draws less than 5A at 220VAC
@heinrichgerber70603 жыл бұрын
Just check the start-up current does not exceed 10A
@bnrboys70783 жыл бұрын
Is it works in AC current?
@cyrusrad12393 жыл бұрын
my question as well ...
@deepakvaidya44213 жыл бұрын
Sir, pani line me aate hi pump chalu ho Jaye, aur pani bangh ho ne per pump bandg ho haye aisi circuit banaiye, thanks.
@hazzardfraeed Жыл бұрын
Peace, mercy and blessings of God be upon you. Operating a home pump project through three or several levels to operate the pump and stop it automatically.
@totohajudas75563 жыл бұрын
Dear author, could you please make a video in which to show how to assemble a simple transformerless power supply to power this circuit from a 220 volt alternating current. Thanks for the video!
@TechIdeasAG3 жыл бұрын
Transformerless power supply doesn't have insulation from the main's. So that can't be use in this project
@totohajudas75563 жыл бұрын
@@TechIdeasAG Then what kind of small-sized power supply can be used in this project?
@alarafathmuslimtv87584 жыл бұрын
Can i use 220v AC watar motor???
@TechIdeasAG4 жыл бұрын
Yes friend, you can use ac motor also
@yousafmohamed11363 жыл бұрын
Hi, is there any protection if pump failed to deliver the water
@anilkumarjhanwar65862 жыл бұрын
There are many protection which can be applied .Pressure switch or flow switch etc etc .
@bhagwatiprsad46174 жыл бұрын
भाई यदि आपने बाना कर प्रक्टिकल कर लिया है तो इसे सबको बताना अन्यथा किसी को मत बताना क्योकि जब आदमी पैसा भी खर्च करे और समय भी जब सफलता हाथ नही लगती है तो दिल से माँ बहन के लिये गालियाँ निकल तीं हैं भाई हकीकत मै है तो अपना वाटसप नम्बार दो फिर मै आपको बहुत सर्किट जो कि प्रक्टिकल करके देख लिये है धन्यवद 🙏🇮🇳🌺🙏🇮🇳🌹🌺🙏🇮🇳🌹🌺🇮🇳
@goutamkrsah95113 жыл бұрын
Shi bole
@JREMC24 жыл бұрын
Anything to change if I have 12V supply ??? Thank's
@TechIdeasAG4 жыл бұрын
You can use 12v dc without any modification
@muniraja5317 Жыл бұрын
In put supply given by 12v DC supply was supported this circuit...
@Relaxing-mv1nm3 жыл бұрын
When motor starts relay can not tolerate more than 10A.. What we have to do for this??
@Dishan_Haldar4 жыл бұрын
Direct 220 AC mey chaley ga
@user-ge4dl7zw6r4 жыл бұрын
Does the circuit is working or not
@urielxpxp4 жыл бұрын
How many milliamps does this circuit require?
@heykeliglesias26394 жыл бұрын
Leds and the rest don't take much, the relay will determine that, I would say 100mA above the relay consumption, and normally relays are between 100 -300 mA
@ahmadsubhi32933 жыл бұрын
How to add water pump dry protection when water tank source is empty,help me sir
@heykeliglesias26394 жыл бұрын
For lab tests it's good but it's not practical, you can't use DC inside water, you will end up cleaning the terminals every week....you need to use AC inside the water instead
@fahadkhan80174 жыл бұрын
Kis par chalyah hai Ac par yah Dc par.
@TechIdeasAG4 жыл бұрын
DC
@majorgrey69154 жыл бұрын
А если вода в правом сосуде кончилась, а левый еще не наполнился? :=) Конец помпе? :=)
@Perepodvyvert_s_perevorotom3 жыл бұрын
Да такую же схему собрать, только логику поменять на обратную: сухие контакты - реле размыкается. И два реле в последовательную цепь на одну помпу. Это если в лоб.
@rishichaubey25202 жыл бұрын
Working karegaa yaa nhii jldi batao please
@storojzzz84424 жыл бұрын
субтитры сделай . идеи не хватает или башка плохо соображает. ты же для всех делаешь
@aryantiwari76443 жыл бұрын
Douse it will work 9n 240 volt Ac Moter also 🙄
@dhitoajitriprabowo31472 жыл бұрын
how does it work in reverse? when the water is full the pump turns on, when the water runs out the pump turns off
@vishnucollaborationstudios11753 жыл бұрын
It's not working sir. When try to connect vcc to pin 8.relay will not switch properly and motor runs continuesly irrespective of water level
@bbiswasable4 жыл бұрын
What type of powerful relay use for 1 hp ac pump motor set. Give the full information.
@bhagyashreeghugare83814 жыл бұрын
Use 12V 10Amp realy
@bbiswasable4 жыл бұрын
@@bhagyashreeghugare8381 ma'am i used 12 v 30 amps relay still hissing sound is comming after tank full because supply is on
@goutamkrsah95113 жыл бұрын
@@bbiswasable use capacitor
@mhari_marudhara4 жыл бұрын
it is not working with 0.5 or 1 H.P motor .... that's really necessary.I did it and all system burned. such demo projects only with very small DC motors.Dont make foolish to your subscribers.
@heykeliglesias26394 жыл бұрын
...use a more powerful relay
@hazzardfraeed Жыл бұрын
السلام عليكم اخي ممكن ربط المتحسس بااربعة مستويات تبدا بالصفر وتنتهي بالمئة طوافة مقسمة لاكثر من مستوى لو سمحت وتشرح طريقة الربط لو سمحت اخي العزيز لتحكم بمضخة المنزل تشتغل وتتوقف بالاردوينو بابسط صورة ارجو الاجابة باسرع وقت
@rodolfosoares67473 жыл бұрын
Serve para 110vlts???
@babbuali8363 жыл бұрын
Nice
@pauloalbuquerque9193 жыл бұрын
O relé no esquema eletrico ficou ao contrario.
@toastersock4 жыл бұрын
Excellent, just what I need
@AnandaRajaT3 жыл бұрын
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively 🙏🙏🙏🙏 And whether ac or dc current to be supplied???
@debasishbiswal77893 жыл бұрын
Sensor wire kitna meter se kam karega
@TechIdeasAG3 жыл бұрын
70 to 100 Mtr. Depends on wire gauge
@dirgh_0026 Жыл бұрын
Can i get a circuit diagram of this ?
@abdulquadirkhan85583 жыл бұрын
When it's applied for use. The person using it while motor is on May get shocked.
@satvikjadhav5023 жыл бұрын
Can any 1 explain me the working principle of this model
@cyrusrad12393 жыл бұрын
what's the power source ???
@Guswin3083 жыл бұрын
I like this and I need it
@Money.matters.bro.4 ай бұрын
What if input current is 220V
@DakshDwivedi23102 ай бұрын
2 1m resistor 1 100ohm resistor 1N4007 diode BC547 transistor Relay 6v or 12v 3 100 ohm pin 100 ohm Emmiter to Blue green red sensor wire (each) Red black wire Small water pump Transparent pipe
@rajkishorekisan38903 ай бұрын
I make this circuit but not work why
@VIJAYKUMAR-dv9gp Жыл бұрын
Pls video banaye
@gpravinkumar43244 жыл бұрын
Please check in metal container
@rishichaubey25202 жыл бұрын
And materials required
@ireneorosalesibarra86764 жыл бұрын
Thank you! Regards from Reynosa, México
@prakashpareek63724 жыл бұрын
Power supply 6v ya 22v
@TechIdeasAG4 жыл бұрын
6v
@paulomatos49064 жыл бұрын
@@TechIdeasAG but here is 110v, what can i do?? Thanks ( Paulo /Brasil)
@facts78892 жыл бұрын
Hlo sir please tell me ki transitor bc548 use kar sakthe h
@TechIdeasAG2 жыл бұрын
Yes
@kabalsingh20302 жыл бұрын
powar kine volt a
@ravisavita84022 жыл бұрын
Circuit ka daigram kaha hai vo chahiye
@grindel804 жыл бұрын
Great work! Like
@Ciiads4 жыл бұрын
😊
@ajithnilantha22092 жыл бұрын
Tanks
@satvikjadhav5023 жыл бұрын
Sir can i get simulation circuit sir
@seckisecen94454 жыл бұрын
Çok zekice. This is very wise.
@anisuddin72793 жыл бұрын
It work properly thanks 😊
@AnandaRajaT3 жыл бұрын
Can you pls tell me how much voltage is to be supplied to motor and the circuit respectively 🙏🙏🙏🙏 And whether ac or dc current to be supplied???