New Square Body Build Part 5: Fuel system install and test.

In this video, we go over and test all the parts needed to run dual tanks with an LS Swap. ‪@SummitRacing‬ supplies the fuel tanks and the ‪@tanksinc.8344‬ push lok -6 AN Fuel system with Corvette regulators. ‪@hotrodfuelhose837‬ provides the dual sending units as well as the Walbro 255LPH high pressure pumps. We still needed additional fittings to make all the connections. Once installed, we test both the float signals and our completed fuel system's pressure. #Chevy #gmc #truck #squarebody #c10 #restomod #LS #lsswap #tci #build #engine #trucks #greasemonkeytv #4link #fuel #summitracing #hotrodfuelhose #tanksinc #-an

[@harleymutt8542]

Your video is awesome!! Best one on KZbin. Thank you so much!!

[@demarques1911]

I seen holley offered a 12-378 part number which is a oem style electric fuel pump which does everything for you. Even preset to run a certain amount of pressure. Think he said 58psi. I want to run this on a carb so ill just buy a regulator to turn the fuel pressure down to 6-8psi

[@Jay-wn6uf]

Had to email tanks inc, apparently those npt fittings are for their pumps. I'd advise anyone to just order fittings and line elsewhere, just mimic the including on their site.

[@MichaelChavez-g6u]

How did you like the do things worry set up did everything work OK? I found him on Facebook. I just wanted to know if everything worked out good and what you had to do different to make it all work before I order it.

[@aaronavila8951]

U have any links to parts used I've been needing to replace my tanks but wanna redo the whole system but can't find the stuff online

[@jasondominguez8179]

Man this video rocks. I wish you would review the transfer valve a bit more. I have an 87 that im starting to do this on. I have all the parts you showed minus the wiring harness. I have 2 new dorman tanks as well as 2 tanks inc tanks in my garage. Gotta figure out which tanks to use and return the other tanks. I want to keep the valve switch so i can go between both tanks. I didnt see any fuel lines going to the transfer valve. Any insight on how you plummed the transfer valve would be stellar.

[@Damosgarage209]

Can you make a short video going over how you hooked up the Jabin woods harness. I think most of us wood like to see how you wired it in. Thanks for such a good video, it definitely helped out

[@oldschool-ef4jz]

Would you be interested in selling the cover that went over the fuel tank selector valve on that mounts on the frame if so I would be interested in purchasing it . Thanks Steve

[@RevengeEyeSeek]

Great video! Lots of helpful information. I have a 75 stepside with dual tanks I'm looking to swap to fuel injection. Originally I was going to go with a single Boyd tank, but now I've reconsidered.

[@seanhwy9761]

I have an 1987 gmc dual tank with ls swap. the gas gauge works fine for the drivers side. when you flip the switch for the pass side tank it always reads full. would missing ground wire ore B+ cause it to read full? I would imagine the gas gauge would always fail to empty.

[@mikebsin55]

The selector valve. Where do those wires go. I’m trying to redo mine with new wires. The two plugs on the tanks maybe?

[@OleonG]

Great information!!!

[@Kurnacopia]

This is exactly what I was looking for my 1978 Chevy Scottsdale 4x4 rebuild. I found the parts you used and and will use

[@greddmyles3677]

Ls suppose to be regulated at 58 psi, that Lil bit dies make a difference

[@frankosauto]

GREAT Video so far! I am interested in the harness for the fuel system! Can you give a part number or contact information?

[@dakotamccorquodale2444]

Could post part

[@JoseLopez-sb7bh]

I seen you hooked to the electric wire to the fuel selector but did you hook up the fuel hoses or did you use that for fuel

[@cgrstng]

Wouldn’t the check valves do a better job on the outlet side of the fuel filter as to preventing back flow pressure on the outlet side of that fuel filter/ regulator?

[@mariomendoza8706]

How much power are you pushing I’ve watched your other videos and saw your running a chupacabra cam and saw the trail blazer intake manifold and I’ve seen that the tanks inc kit is only rated for like 450

[@billycooper9879]

What size fuel tank and fuel sending unit. Are you using!!!!!