New Vintage Air install on a frame up square body build!

Entire build: • New Square Body Build ...
Our 1986 C10 gets a complete ‪@va197653‬ Vintage Air A/C and heat system. Here is an unboxing and step by step installation of their Gen IV Sure Fit Kit. #C10 #chevy #truck #restomod #vintageair #A/C #greasemonkeytv #squarebody

[@henrytaylor3049]

I really love the cup holders frenched into the seat👍. The argile in the engine bay and the seat is pretty sweet too...❄️ Truck.

[@red93yj]

dude, that truck is amazing!!

[@LaMalditaC10]

That’s a really nice truck. Congratulations 💪🏻💪🏻💪🏻

[@bobdaily836]

nice job, thanks for the updates of what needs to be done

[@ericdavis7002]

Great information! Love the truck! Color combo!

[@NaztyNate]

THANK YOU for such a great install video!!!!!

[@Flyguy843]

Sweet setup. I’m planning to do my truck soon.

[@eddiedominguez7055]

Really nice job

[@cwmotorsports4497]

Thanks for the video!!! Very informative.

[@yourboij82]

Nice one! 👍🏾

[@billlloyd9755]

Nice pickm up truck 😊

[@robertoherrera9793]

Thanks!

[@gbertostorage1575]

I need this

[@pablotonche5780]

Awesome video. What’s the belt part # if you don’t mind sharing. Ty

[@ParadiseOnOctane]

Great work,Which vintage air kit are you using??💪

[@michaelhood1291]

Fantastic video! 🇺🇸💪🏼 Can you tell me how much real life time this Vintage Air install takes?

[@GreaseMonkeyTV]

Probably 4-5 hrs on a completed truck.

[@billyconnell5628]

bad ass truck sir how did u go about wiring the ac control to the idle air controller or ecm to make motor idle up when ac is on?

[@GreaseMonkeyTV]

You can send a signal to the PCM via a designated wire in most aftermarket harnesses.

[@CaseyDillon-os4kd]

What did you do to make the defrost vents fit? I don’t have any factory holes to screw to although my truck is factory air. I could also not get my u-nots to fit. Thanks in advance. Great video and truck as well!

[@GreaseMonkeyTV]

Interesting. Your factory air truck doesn’t have the defrost mounting holes?

[@CaseyDillon-os4kd]

No sure doesn’t! It is a factory air truck as I removed the factory AC. Thank you for your reply. Sent email to Vintage AC. Every other video I watched everyone just screwed them into place.

[@NDB390]

What high mount bracket did you use? And was your truck a factory air or non factory. I have a non factory and finding that it’s a lot more money for a non A/C truck. If the main difference is inside duct work then can a guy just pull duct work from a donor and save some money?

[@seanjordan4485]

What gauges did you use?

[@benjaminnewsom9193]

What gauges are you running on this build? I’m like those a lot

[@GreaseMonkeyTV]

NVU

[@handyrandysgarage6929]

I have close to the same set up as you. I’m having a issue of the idle rpm dropping so low sometimes at a stop light that it kills the engine when the ac clutch cycles. Did you do anything to bump up the idle when it cycles?

[@GreaseMonkeyTV]

Your tuner should be able to fix that.

[@apluspooldesigninc6122]

what size are those wheels?

[@martinolivas319]

I’m having issues finding why my factory climate control system constantly pulls in air from the engine bay. My Exaust is leak free, but at stop lights I pull in Exaust from the surrounding vehicles. Any advice would help

[@GreaseMonkeyTV]

Turning your air to recirculate uses only the interior air.

[@baderalsaho2912]

please can you make it a video to explain how to read and working ecu with o2 sensor in your car with knock sensors my truck is swap ls engine not read it I have problems with low voltage knock sensors bank 1 bank 2 and please anyone one help? With that issue

[@GreaseMonkeyTV]

Probably need to seek out a good mechanic in your area.

[@pablotonche5780]

What belt did u use ???

[@GreaseMonkeyTV]

Can’t remember. Tried about 3

[@crsmith56]

Do you dare to give us a complete price list of what it cost to build?

[@GreaseMonkeyTV]

😂 not a chance.

[@crsmith56]

GreaseMonkeyTV Don't blame you! Thank you for the info and inspiration on the build. Awesome C10!

[@JeLifeCoach]

@@crsmith56 Chassis 23K plus, motor and trans (20k), VA kit (2200), wheels and tires (3k), sound system (2-3K), interior carpet and dress (2200), chrome bumpers and trim (1-2K), finding a project truck (8-15K), paint (who knows probably 20K). I’d say well over 70K.

[@jasonfarnsworth5880]

Probably more like 85