Thanks man. I sat in my garage realizing there were 4 ways I could install that bearing clip. Your vid answered my question of which way was right.
@user-rm5kx6ct2w Жыл бұрын
Thanks for the video and your time deicated to share info. Upon viewing the first section tabs are on the fork one way and then when installing the fork through the tranny the tabs are set on the bearing another way? Phrasis like, SOMETHING LIKE THAT, THIS GUY HERE. Dosent leave me with a whole lot of confidence
@garagemonkey526 Жыл бұрын
I believe the bunny ears are away from the shift fork
@sendit5310 Жыл бұрын
This is informative because you show the spring going in the wrong way at first 1 star
@scottscontracting2 жыл бұрын
thank you for the suggestions! mine went together easy-peasy after watching and imitating how you did it! peace
@AGuysGarage3 жыл бұрын
Little bit too chatty most people just want to know about the spring but thanks for posting
@luvayeavocado53772 жыл бұрын
agreed
@adamp70698 ай бұрын
Bro speaks yapanese
@RyanGrosz2 ай бұрын
He’s being thorough for those that want to learn more than you.
@awong1602 жыл бұрын
Nice advice! I used it for my 04 Frontier!
@KrazyRobb3 жыл бұрын
At one point the clip ears are facing inwards towards the fork then they are placed facing outwards later. Which one is it?
@Gullygook2 жыл бұрын
Lmao I struggled for literally 30 mins putting it in the opposite way. Is the last direct he shows. Obviously you don’t need this information but I’m sure someone next time will.
@alexcleaho6159 Жыл бұрын
I say what the fuck lmao
@sendit5310 Жыл бұрын
It’s a bad tutorial I reckon
@user-bu8bc6kg4f6 ай бұрын
Thanks i was wondering @@Gullygook
@lawrencer5882 ай бұрын
THANK YOU!
@moy34363 жыл бұрын
I removed pilot bushing .No pulling ! Just am impacted drill drove medic bolt into pilot bushing and pilers to wiggle out ! 5 minutes 98 frontier 2wd 5speed
@danielw70602 жыл бұрын
You can pack bread behind it too, put a socket in the center and hammer away.
@SpaZeo3 жыл бұрын
I’m behind you at the drive thur, at better buzz
@altoncaldwell236111 ай бұрын
Thank you, my guy
@freddyfresh15902 ай бұрын
You put it on 2 different ways. The fork and clip. Which is the correct way?
@Joshua_Hammer.777 Жыл бұрын
Thanks for the video
@ncmaximaguy62672 жыл бұрын
Nice video. Thanks
@user-dc4sz7cm8k6 ай бұрын
LUK clutch kit- have to bleed it every day to drive it...makes noise when shifting...no leaks ? anyone know why?
@dsavage8751 Жыл бұрын
Trying to press the bearing in using pipe and hammer doesn’t work with out a press, (Z32)
@dnacannotchange6 ай бұрын
how did you get it off? Local shop said they could not install the bearing to the old sleeve....
@dnacannotchange10 ай бұрын
how do you install sachs bearing?... It's not assembled on to the Part
@jackpotcity92732 жыл бұрын
WHAT WAY IS THE CLIP ?????
@laurapichon76232 жыл бұрын
the last way he had it seems to work best for me, currently doing it on my trans
@leighhannah8069Ай бұрын
Well damn. I thought I was getting some help. I forgot there aren't any good people out there to help a person without getting paid. Never-ending. I am a 71 year old woman needing help. I will go elsewhere. Maybe the truck will fall on me ND I wint have to worry about it any more
@alwyzDTFСағат бұрын
shut up
@trifeski Жыл бұрын
So I have a question 2 years later haha. @3:01 you clean up that shaft. It’s on a plate bolted in there. Mine was snapped off when I opened mine up yesterday. WHAT IS THAT PART CALLED PLEASE!!! ANYONE! Lol
@andrewe7974 Жыл бұрын
same thing happened to me last week lol
@Dnay54543 жыл бұрын
But how do you take the bearing off?
@danielw70602 жыл бұрын
Just pull it, some resistance is normal.
@sparklingsams31553 жыл бұрын
Hey mate after installing the fork to the engine it's impossible to move back and forward with hand. My engin is in the ground btw. Is this normal.
@JaboTheMechanic3 жыл бұрын
Thats fine. You should have about .005inch of play which is next to none.
@sparklingsams31553 жыл бұрын
@@JaboTheMechanic thanks mate
@mevin2002 Жыл бұрын
do u need to drain the fluid? my drain bolt is rounded
@JaboTheMechanic Жыл бұрын
No you dont but it will leak
@gerardolopez58752 жыл бұрын
How much its that labor cost??? 🙏🏻
@matyrobloxtoonsandanimatio61073 жыл бұрын
Hi
@jhamgarces97703 жыл бұрын
it' obvious. hehehe
@libsrmarxist29 күн бұрын
You should probably know what you're doing before you try and make a video showing people how to do it.