Thank you. Used this process today on my son’s truck. Worked like a champ. Cost was less than $25. Saved $2400 from the local mechanic quote.
@brucejr.5833 Жыл бұрын
You have saved a lot of us so much money. Thank you man really.
@GabrielSvenbörk4 күн бұрын
Thanks Mr Busey!
@user-qq5yx8jl7u6 ай бұрын
Very informative straight to point and clear.... WELL DONE.!
@mcmenace484713 күн бұрын
No this is old but would this work on the vg30-e should I buy the factory nissan sensor, any info wld be great.
@ktomes600926 күн бұрын
You so much for the wonderful video
@danielrowan5690 Жыл бұрын
Thanks Matt!!
@yolanikenny6407 Жыл бұрын
Can knock sensor fail the Nissan elgrand vg33 fail to start?
@JnRskaters10 ай бұрын
Did you get your fixed
@mmmejias18 Жыл бұрын
Now the check engine light is off but the sensor is not feeling the knock which helps the computer with timing.
@natepressley337911 ай бұрын
Exactly! 🤪🤙
@billsmathers302110 ай бұрын
Matt good information thank you. Any chance you did the timing belt video? I'm considering doing mine I have 92k on mine , recent purchase.
@JorgeJasso-x9w Жыл бұрын
You are a genius!
@myysticranger4 ай бұрын
It is even worse for us with the supercharged VG33. I've got a 2003 SE/SC Xterra and that KS has been going off and on since I bought it back in 2009.
@Detoxingforlife Жыл бұрын
Thank you brother short and sweet! Xterra brotherhood lol
@Debosway77 Жыл бұрын
So why use a 1999 Nissan Maxima Knock Sensor instead of the Xterra one?
@GMJLopez Жыл бұрын
From what I've seen, the 99 Maxima has a harness that cheap and easy to source.
@kaydenday67023 ай бұрын
Does the knock sensor actually need replaced? How do i know if its the knock sensor or the actual engine thats causing problems
@gm-classics3 ай бұрын
Very common issue. This fix is good for life of vehicle without a big teardown
@kaydenday67023 ай бұрын
@@gm-classics i feel a little dumb but i understand now. I need to replace my sensor completely.
@Bk6634Ай бұрын
I did this same process and now my ecm says N/A on every function test when you hook up a code tester . It still idles very rough. I checked the ohms on the spliced wire on the new knock sensor and it has resistance. Any one else has this issue? My truck computer won’t read anything now. Seems like when I cut that wire it messed up my ecm.
@Bk6634Ай бұрын
I changed the 2 upstream o2 sensors because before I did the knock sensor relocation the computer was throwing a o2 sensor code and knock sensor. Now it doesn’t show like the computer is reading any sensor . Very frustrating.
@robertthomason8832 Жыл бұрын
Do you know what the part number for the maxima knock sensor you purchased?
You n ver have sensor parameters on good condition, knock sensor needs to be install on engine block, sorry, you are wrong
@gm-classics4 ай бұрын
It may be “wrong” but it works… some with over 300k miles PAST doing this.
@ihaveastory613210 ай бұрын
Great vid! I was able to reach around and under and was able to disconnect my old sensor. he original harness is long enough to do this relocation without cutting the wires. Also if you use an aftermarket sensor you will often have to replace the cam sensor too. This video explains why aftermarket sensors set off other sensors and sometimes have problems kzbin.info/www/bejne/hpvJXqeXmL2CpKs
@Руслан-з1ф Жыл бұрын
bad idea
@gm-classics Жыл бұрын
Several done at 70-80k with 250k on them now… we have different opinions of bad ideas