Thanks for this it took quite a while to do the job even with a wiper blade tool but at least I knew what I needed after watching this.. Repaired the connection and refitted so all is good for now. Thanks.
@clerko6711 ай бұрын
Great clear concise video, thanks
@pwkish3 жыл бұрын
Great video. So well filmed and explained.
@philippmery36916 ай бұрын
Gracias por el video, genial, facil y practico!
@connienail40133 жыл бұрын
Great video! If only I had the feckin tools (and the brain!)
@muhyijeilan89699 ай бұрын
Thank you
@manyakadikalo98533 жыл бұрын
Thank you!
@Phill11318 Жыл бұрын
Just watched the video as my qashqai has the same problem, just a question about the tools I need. Is it just a 10mm socket reachet I need? Cheers
@joshkeogh51126 ай бұрын
Hi i followed all these steps but when i hand tightened the wipers to test the dont move and are getting stuck any sugestions?
@MTMMotorServices6 ай бұрын
You'll have to tighten them down with a ratchet if you don't feel it is tight enough, the splines on the spindles won't grip the wiper arm so they will slip and the position will be wrong.
@aminfater85863 жыл бұрын
Thanks you diagrammes motur
@derekryan57602 жыл бұрын
My qashqai is 2011, driver side wiper hits side of window, and seems the linkage is okay and motor, issue is..the spindle that wiper sits on is worn..is there an easy fix solution rather than replacing linkage???
@sikanderhussain8143 Жыл бұрын
I fitted the linkage and motor to my Qashqai. The problem I have is when I turn it into park position it stops at the top not bottom. Could it be a faulty linkage ?
@MTMMotorServices Жыл бұрын
I would remove the wiper arms, run the motor till it stops and re fit the arms in the park position and try it again. If the park position changes then potentially you have a defective motor
@sikanderhussain8143 Жыл бұрын
@@MTMMotorServices I did exactly that. I took the wipers off and ran it till it stopped, the stop position was at the top.
@janoates89744 жыл бұрын
Can you get the wiper arms off without that particular tool?
@MTMMotorServices4 жыл бұрын
Yes you can. In 90% of cases I've not needed to use that tool, this time though they were particularly tight on the spindles.
@janoates89744 жыл бұрын
@@MTMMotorServices I managed to get the nuts off but still can't get the wiper arms off. The mechanism has been reattached through the inspection hatches now so no longer need to get the arms off. For now anyway... :-) Thanks for your help. Great video.
@betatucanae1241 Жыл бұрын
Yes, Took a few bangs of a hammer, unscrew the nut up but with threads still aligned with the left and bang the nut not the bolt. .
@larchielad Жыл бұрын
Do i need def need wiper removal tool?
@sukeshbabulal1668 Жыл бұрын
No
@NELSON39473 жыл бұрын
I've replaced the motor on mine. Now the wipers always drop down a few inches first before going up. So, I have to have the park position quite high to start. Any ideas?
@MTMMotorServices3 жыл бұрын
Did the linkage come pre positioned on the motor? I'd say you could try removing the linkage, wait for the motor to return to park position and then re fit the linkage and try that. Otherwise it could be a bad motor with an incorrect memorised position.
@NELSON39473 жыл бұрын
@@MTMMotorServices Thanks for the reply. I bought the motor and fitted to the OEM linkage. The old motor was doing the same. Very weird! I watched the motor before I installed it and it went one way for a bit, then went into normal operation!