NISSAN: Replacing A/C Pulley & Clutch

Here is where I bought mine.
clutch amzn.to/3H3hGUU
snap ring pliers amzn.to/3H3hYes
3 jaw puller amzn.to/3IG9zOs
jack stands amzn.to/3qYXGgu
jack amzn.to/3IJp885
camera amzn.to/3uni2SF
Tripod amzn.to/3HrZdBy
if you want to support my chanel you can donate to it
here @ www.paypal.com...
or
But you can still
Buy me a gift :) www.amazon.com...
I'm replacing the ac compressor clutch on a Nissan murano se AWD.

[@amberbeach8459]

This is EXACTLY what I needed!! Thanks so much! I fixed the car myself ☺️☺️

[@justinsworkshop6636]

Your welcome glad I could help

[@leeroethler4846]

Awesome job it's good to see someone do a real service video the way it's supposed to be done , I watched 3 before this 15 to 30 mins long driving to the part store for a none oil filled compressor (no pag oil, expansion valve , no system cleaner )then not doing the repair on video?? Then charge the system with 12 oz top off can calls for 1.8 pounds without vacuuming the system and no temp check . You know HVAC system's and I didn't yell at this video so wife liked it to lol . thanks for the time saving advice I was going to do it on the bench so saves me a lot of work .

[@justinsworkshop6636]

Yw. Glad I could help. I try to keep my videos short and to the point.

[@AcoustaManDon]

Very good vid because it's clear with the image and description,. Was considering going to mechanic, but now--gonna go for it!

[@justinsworkshop6636]

Thanks. I'm happy that I was able to help

[@Nelsondoremi]

I was going to buy a new compressor, because when I start the engine, sometimes it makes a loud noise. Now I see that it could be the clutch, because the compressor cools, good. After it warms up (about 5 seconds) the squeal disappears. Thanks for your video

[@justinsworkshop6636]

If it's squealing, you make make sure your belt is tight enough when your belt is loose it will squeal for a bit, then stop . I would hate for you to replace something that doesn't need replacing.

[@luisduar573]

Great video, it show you that it's not easy but not complicated at the same time,

[@chrisdaniels4674]

If you don't have a gear puller and you have some bad ass drill bits you can drill through the old pulley if you are replacing it and then take out the 3 Philips screws after disconnecting the wires. If your throwing that part away and don't want to pay for a new tool.

[@davismize]

Great vid and informative. You try to answer everyone's questions too. Keep the vids coming. The more you have the higher your placement. Eventually you can make some serious income off of it.

[@justinsworkshop6636]

Thanks. I try to keep it sort but still go over everything and not get carried away with nonsense. I need to make more just been to busy

[@grayze07]

Somehow the clutch screw and washer had fallen off mine and thankfully got lodged in a gap so I was able to locate my issue. I was getting really bad rattling and the plate was loose. Im going to try this and hope nothing else is broke

[@ls6king316]

This video goes to show you how mechanics lie and say that you need a whole AC compressor so they can triple charge you for it parts and labor

[@vicentegonzales3852]

This video is good for true owner save a lot money by looking at KZbin

[@TheCloser1]

Or you pay double labor when you replace a clutch on a tired compressor and have to do the job again soon after..🤷‍♂️

[@bossredd-77]

Exactly what's wrong with my Quest 09. Thanks a lot.

[@justinsworkshop6636]

Yw glad I could help

[@gfysyoutube]

Excellent video. Thank you!

[@bigdoggy6650]

Thanks!

[@NeutronX101]

Wow that clutch plate came put pretty easily.

[@joedaquila2646]

Thanks for the great post, you made this repair very easy..

[@justinsworkshop6636]

Your welcome. I'm glad I could help.

[@bowendeng1241]

Great video. Thank you for the very detailed steps. I am wondering if you still remember what is the size of the puller tool or if there's a specific type I need to buy.

[@justinsworkshop6636]

Yw I'm glad I could help. Good luck with yours. The pullers I have is a kit I got from Harbor freight it comes with 3 sizes I believe I used to larger one that came in the Harbor freight kit. On there website its called Three-jaw puller set, 3pc

[@alimolero930]

Thanks 🎉

[@DarylBoshears]

I'm thinking this is exactly what's wrong with my Nissan Murano, it's making a rattling noise and not blowing cold air...hopefully this is the fix! With this issue, I shouldn't have to replace the compressor?

[@Tom-ls1vi]

Nope, pressure is pumping fine, in my case, the coil was bad. Replace the coil, pulley, and clutch, and she runs like new dealer cost to replace compressor was $1200. My cost? 50 bucks and afternoon away from the wife in the yard.

[@str8blaq]

Gr8 video thanks for sharing. I went to this amzn link it's on the way.

[@justinsworkshop6636]

Thanks. Your welcome. Good luck on yours.

[@Z33_Unknown]

some how my clutchwent missing on my 350z so im just replace the clutch luckily

[@justinsworkshop6636]

@@Z33_Unknown clutch is cheaper than a compressor

[@ShaneAlan1]

How can you tell if it is the clutch or compressor that needs to be replaced?

[@justinsworkshop6636]

@@ShaneAlan1 is the couch making a noise? Is the clutch coming on? What's it doing?

[@grilledchickenwrap]

great video... now I have some confidence... any idea whats a good jaw puller I should get for this ?

[@justinsworkshop6636]

I have the one from harbour freight I believe it's a 3 pack

[@grilledchickenwrap]

@@justinsworkshop6636 used the 3 pack 2 jaw puller from HF. Worked really well… I think that was the best $20 I spent lol. Super happy have AC now. Big thanks!!! For your video. Btw I did this on a 2014 Pathfinder..

[@justinsworkshop6636]

@@grilledchickenwrap good glad my video helped. If you took it to a mechanic they probably would of installed a whole new compressor and charged you to vacuum and recharge your system. $$$$$$$$$$$

[@grilledchickenwrap]

@@justinsworkshop6636 exactly what they wanted to do…. I was like. WTH i need to replace the compressor when just the ac coil was bad ??? They wanted $300 for replacement and I have to buy the compressor, I laughed at walked away.. ordered my coil clutch kit on eBay for $45… Spent 2 hours slow paced abs got the job done… it feels soo good afterwards when AC went on and cold air blew out lol

[@dingobabie]

I have a Nissan maxima and it blows cold air but squeals when I turn on ac and I smell like burning rubber so not sure if this is the problem ?

[@justinsworkshop6636]

Sounds like belt is loose and slipping.

[@ddtrudeboi]

Thanks great video

[@justinsworkshop6636]

Yw glad I could help

[@adrianrog]

Justin, Thank you very much for your video, it is very well done. What parts do I look for other than the AC Compressor clutch? Is there a kit to buy that has everything I need in int?

[@justinsworkshop6636]

Thanks. You will need snap ring pliers screwdriver and probably a puller. You buy clutch kit has all the clutch parts if that's what your asking. Doesn't come with tools. Some part stores will rent you tools. Good luck.

[@adrianrog]

@@justinsworkshop6636 Thanks, I have all the tools, just wasn't sure what to call the kit. I'll look for a clutch kit and see what I come up with. Thanks again,.

[@justinsworkshop6636]

@@adrianrog I normally go Amazon and type in ac compressor clutc and my type of car

[@adrianrog]

@@justinsworkshop6636 Thanks, I think mine is just an oddball, I've done some serious looking. It's looking like I may have to buy a compressor or used clutch/coil/pulley. Anyway, thanks again.

[@justinsworkshop6636]

@@adrianrog yw good luck 👍

[@carlosalejandrorodriguezcu2791]

Thanks for sharing...great video..!!!

[@justinsworkshop6636]

Your welcome glad I could help

[@perez7667]

Hello, Sir. If you were to check resistance of the clutch, you would do it against ground, right? Also, it you were to energize the clutch, would you be able to put the voltmeter into the COM port and the 10A port, then red lead to battery positive and other lead to the clutch wire?

[@justinsworkshop6636]

I really wish I could help you but testing electrical is my biggest weakness. And I don't want to tell you wrong. Sorry

[@frozendonkey9622]

Honestly never seen a clutch come off like that, they're always stuck on the splines.

[@millertrucking2381]

What about the little spacers that come in the kit? Did you use them or just discard them?

[@justinsworkshop6636]

I used the same ones. That were already there because the space was fine still.

[@hectoraztlan5131]

Hi Justin, thank you for posting your video, it's great and with great detail. I'm just changing the same pulley/clutch kit but for my XTERRA 07, so I had to remove many parts to have access to the compressor. The only difference I see with my compressor is that instead of a bolt in the clutch like yours, mine came with a allen bolt, that I already removed. I still have to pull out the clutch because it's pretty stuck there. Any suggestions on how to pull the clutch? Thanks!

[@justinsworkshop6636]

Yw I'm glad I could help. I used a 3 jaw puller you can get a inexpensive 3pack at harbor freight if you don't have one or idk if the have that but you might check with your part stores some have tools they loan out. Good luck.

[@glenparris9317]

Am trying taking out a shim because on the run am not cooling much

[@justinsworkshop6636]

Do you have enough freon in it?

[@orlandozayas7255]

Why is it that the new ac clutch has two shims, but once installed, is very tight when it spins?

[@justinsworkshop6636]

It shouldn't be. Did you try your old shim to see if it made it looser?

[@mauriciodiaz-hinojos5046]

Am trying to take off my old one out, but i don't see a snap ring on it, Should I just remove it with the puller?

[@justinsworkshop6636]

Ya you can if it's replaceable. Not all clutches are replaceable.

[@HighVibeMike]

What noise was the clutch making when it started to burn out on you?

[@justinsworkshop6636]

The bearings were Squealing for a while but then it just stoped working.

[@jesskyb8163]

Hi, Do I need to use an Impact as you used on the bolt? I tried using a ratchet and powered the clutch to prevent rotation of clutch, but the bolt seems quite tight I'm afraid to strip it any recommendation would be appreciated

[@justinsworkshop6636]

Yes that's what I did at first to break it Loose is I used an impact

[@jesskyb8163]

​@@justinsworkshop6636 Okay I might have to get one to remove it then, Thank you I appreciate it

[@justinsworkshop6636]

@@jesskyb8163 if you sent have one something I've done on bolts like that that turn a pully is put your ratchet on it and get a hammer I prefer rubber mallet and hit the handle of the ratchet. It kinda works like an impact and will break it loose. Good luck hope it helps

[@jesskyb8163]

​@@justinsworkshop6636 Okayy, Thank you

[@vicentegonzales3852]

So … on shim washer … should I use old one or what should I put ?

[@justinsworkshop6636]

I used the old because it was still the correct spacing. You just need to make sure itsvnot to tight because it will drag but if it's to loose it won't grab.

[@cliffordmcintosh8291]

What if you don't have the 3 screws on the magnetic coil? My 2010 Nissan Rogue doesn't have the 3 screws in the actuator. How do i pull that off. Nobody has an answer. Nissan won't tell me anything until I pull the vehicle into their garage.

[@justinsworkshop6636]

Sorry I'm not sure I havent done that one. I would have to look at it.

[@cliffordmcintosh8291]

@@justinsworkshop6636 fair enough

[@davismize]

No change in the process. It saved you that step. I know this was a year ago this is for the next people that see this thread.

[@discoonelove]

Thank you sir God sent 🙏 where do send the check ✔

[@justinsworkshop6636]

Your welcome I'm glad I can help. If you want to support my channel I do have a PayPal account set up for donations if people want to donate. The link is in the description.

[@discoonelove]

@@justinsworkshop6636 seriously got a quote for 1,200 just today, I'm a big guy I need my ac in traffic lol 😆 appreciate you sir

[@justinsworkshop6636]

@@discoonelove yup that's why I started making videos. Most shops will rip you off. They probably would of installed a new compressor plus evaporator then charge you to vacuum and recharge your system and who knows how much for the freon when all you need is a clutch. I love when I get comments like yours stating I helped you out and you were able to do it yourself.

[@davidvoorhies812]

You're amazing. Did you ever get Amazon back up? I'd be happy to use your affiliate link.

[@justinsworkshop6636]

Ty. No they won't till I reach 500 subscribers. They say I have enough views per month though

[@davidvoorhies812]

@@justinsworkshop6636 I hope you get there soon my friend. I do appreciate the info.

[@justinsworkshop6636]

@@davidvoorhies812 me to. Yw glad I could help

[@knight-ue6tf]

I turn the car as soon as I turn a c my car stalls can this be problem at first it was working I would hear weird noises on front air conditioner haven't use my a c cause that issue it stalls the engine plz help

[@justinsworkshop6636]

Your compressor might have locked up. So when you turning on your ac your activating that clutch causing a major load on the engine. Probably need new compressor

[@davismize]

Yep, exactly right.

[@knight-ue6tf]

I took the clutch off and disconnected the wire and the pulley running fine but no a c can I run it like that for a while

[@justinsworkshop6636]

@knight-ue6tf so you unplug it and put clutch back on? Ya you can run it like that just fine.

[@knight-ue6tf]

@@justinsworkshop6636 no clutch and the pulley turned freely with belt on so I guess the air conditioner is not locked? Just not running a clutch till I save for a whole unit and condenser and dryer

[@adriansantamaria6006]

My compressor is leaking from the pulley do i need a new one?

[@justinsworkshop6636]

Sadly yes.

[@bbmd2200]

Hello, Sir. I removed my ac clutch, and when I put it back, it spins with the pulley while the AC is off. Do you know how I can fix that?

[@justinsworkshop6636]

Did u put the shims in it? If so you might need to add another shim. Look at 7:08

[@bbmd2200]

@@justinsworkshop6636 I only saw 1 shim and put it back in. Maybe, there were more shims that I couldn't find.

[@justinsworkshop6636]

@@bbmd2200 maybe. That one i installed came with new ones and I had the old ones. If there isn't enough shims when you put the bolt in it will pushe the plate against it there needs to be a air gap in between the plate and pully but if you have to much air gap it won't work either. I would suggest checking the box and all plastic and around your work area for them. You might be able to buy them to. Good luck hope you get it.

[@JoyLong]

What was the spacing between the clutch and the pulley?

[@justinsworkshop6636]

I'm not 100% sure I set that one back to what it was you just want to make sure it's not rubbing when you spin it

[@jeffevans6973]

Where can u buy just the ac clutch

[@justinsworkshop6636]

I bought mine on Amazon I believe but you might be able to get it at a part store

[@NeutronX101]

Do you have to lube anything?

[@justinsworkshop6636]

No

[@carlosalejandrorodriguezcu2791]

hi.somebody can help me please..!!! Where can i buy clutch..???

[@justinsworkshop6636]

I ordered mine online

[@jorge55122]

Could you leave the link on the website to get that spare?

[@justinsworkshop6636]

I bought it on Amazon.

[@jorge55122]

@@justinsworkshop6636 Thank you ... and what are the symptoms of that piece when it is damaged?

[@justinsworkshop6636]

@@jorge55122 my bearings were making noise when I first decided to replace it. You will just need to diagnose it. Check out this web page hope it helps. itstillruns.com/tell-clutch-ac-compressor-bad-7649305.html

[@deasttn]

2:40 My center bolt won't come off. It's on tight.

[@justinsworkshop6636]

@@deasttn I used a impact to loosen mine.

[@ls6king316]

Dude, did you get attacked by a dog in the middle of the video? 😂

[@justinsworkshop6636]

Lol. Someone was walking down the road my dog started barking at them.

[@davismize]

Great dog.

[@Astralpilot2.0]

The slow motion bit. What angle did you access it and is this a pathfinder

[@justinsworkshop6636]

If your talking about what angle did I have my snap ring pliers? I have tips on them that are at a angle and I was going in the hole straight my tips are a little worn that's why it popped off