Nissan rogue lower control arm replacement

like comments and subscribe and share the love.
help me help you by donations no matter how small it is i really appreciate it here is my link to PayPal send it as if you are sending it to a friend
www.paypal.me/Momoboss5
thank you for your love and support

[@mknss9186]

hey man thanks to you i repaired my car again

[@Farmer3190]

Good video. Plenty of depth, zero BS. RESPECT.

[@mr.z3161]

Great video . Very clear and easy to follow

[@leroyreed1215]

Thank you for the video good job you make it look so easy but with the right tools and attitude anything could be taken care of

[@AustinFloorguy]

Easy enough... Now, I just have to go get a good decent Metric socket set for my impact. I'm a Mopar & FoMoCo type of guy. Very few metric tools. I may have an 18 and a 21 in 12 point hand sockets, but not for my impact, that needs 6 points, or it trashes them and the bolt head. Thanks for taking the time to film it.

[@danc1926]

Dealership quoted me $1700 to get this done 😂 20 minutes later found the parts for $180.. going to replace them myself in couple hours time, thanks for the help.. ain’t nobody got that much money to waste in this economy I can’t believe people won’t do easy work like this at home. Thank you! 🙏

[@MtPockets14U]

Quoted the same.. and another $996 outter tie rods. On a 2017 w /32k miles.. what a POS car. Just replaced the engine fan. That I happened to get on Amazon for $80. Had it in dealer today for 30k tranny fluid flush. $309.

[@bennythomas9798]

Thank you for a job well done ! Hope this helps me today while I do the same thing to my mothers car

[@maxodorestant9053]

Great video, keep up the good work.

[@brycetheobald5512]

Amazing my dude, very well explained hard to find good honest people like you. Earned a sub look forward to more of these. 🤟🏻

[@zanaco69]

Thank you Dullah you are the best

[@hadroncollider9047]

Great explanation for the process. You made it look really easy and you did this with one hand holding onto the camera . Great work.

[@Dandan-ef5mh]

Thanks man! Good video

[@chrisfraser9457]

Great video however I'd recommend using a jack to push the new ball joint in rather than a hammer, customers tend to not like strike marks on their new parts.

[@eduardocertain2227]

Good video buddy!

[@mava5634]

very well explained,

[@JMacomber]

Great work!!

[@franckypena6451]

Thanks smart work

[@mohammedalazzawi9388]

Good job

[@danc1926]

Subbed!

[@devellwilson7099]

Thanks for the knowledge brother

[@adrianmartinez7170]

Do you have a video on how to replace the front strut on a 2018 Nissan Rogue ? I mean that 2017 ain’t no different would much appreciate if you can do a video on it. Great work.

[@JulianKlauz]

Do you know the torque specs for tightening all the bolts at the end?

[@PiratesOfDoom]

Thank you for posting this video. This has been SUPER helpful as I have found myself needing to replace the same part on my 2017 rogue. Do you have any videos on bearing replacements for a 2017 nissan rogue sv too?

[@DULLAHGOSOHARD]

Yes

[@PiratesOfDoom]

The sway bar is in the way of the last bolt on the control arm so I can't take the control arm off. What was the best way to get to the bolt on the control that's nearest to the sway bar? I tried taking the sway bar link off but it wouldnt budge.

[@DULLAHGOSOHARD]

It should be the same as the altima and u have a video for that

[@DULLAHGOSOHARD]

You just need some to hold the nut and unscrew the bolt from the bottom

[@thickangie504]

First video I've seen for a newer model rogue.I'm looking for control arm parts for my 2015 rogue (not select). Do the newer models only have lower control arms and not upper arms? Can't find any parts for the upper control arm so I can only assume it's not needed.

[@DULLAHGOSOHARD]

I know They come with lower control arm no upper

[@thickangie504]

@@DULLAHGOSOHARD Thanks for this info!

[@fhidalgotvlogs459]

Hi sir question no need alingment after replace?

[@buckct147]

Hey brother how much pounds is that hammer?

[@papitosabe]

Nissan wants 2500 for the control arms and outer tie rods ...front

[@303adrianarian9]

That’s crazy Amazon you can get for around $100

[@joesno406]

Good work My Bro! but is an alignment really necessary after control arm install on this car??

[@DULLAHGOSOHARD]

Yes you don't because it will destroy your tires

[@joesno406]

@@DULLAHGOSOHARD Yea but alignment points are on inner tie rod only on this car? NO?

[@DULLAHGOSOHARD]

@@joesno406 true but its always good to do an alignment after working on your suspension worst if the parts was worn out or hit hard and bent

[@mknss9186]

I can NOT open the 2 bolts with 21 mm .. the sway bar is on my way please help im waiting you

[@mknss9186]

Im working on the driver side

[@DULLAHGOSOHARD]

Disconnect the sway bar links on both side andbyou will be able to move it up and down out of the way

[@mknss9186]

@@DULLAHGOSOHARD thank you very much i repaired my car! .. thank you ❤❤❤

[@jasonmckeaigg9143]

You must be hourly paid...got to hustle to make money ..👍