This will most likely be a 3 part video as there lots to do and will be broken up over a couple months waiting on axles, the Dana 60 ring gear just won’t hold up to the power level we are at anymore.
Пікірлер: 24
@bradywilliams26662 ай бұрын
I'm gather parts to build a rear 14 bolt steer axle. But why not in your case just put dana 70 gears in the 60 housing? Jantz makes a kit.
@rosinsautofab1956Ай бұрын
No pinion support on a 60/70 I make to much power and the pinion was deflecting away from the ring gear stripping it out
@sexualtyrannosaurus1856 ай бұрын
I'm so Fu@ken jealous 😫. But seriously that's fu@ken awesome.
@rosinsautofab19566 ай бұрын
Thanks! It took me a year to collect all the parts😂
@huckstirred71126 ай бұрын
did you drill oil ports for the bearings , and did you get custom cut reverse rotation gears
@rosinsautofab19566 ай бұрын
No modifications were done to the internals of the center section
@BeardBuilds Жыл бұрын
Did you retube it or buy it like it starts in this video?
@rosinsautofab1956 Жыл бұрын
I had a buddy re tube it, Richard at trail tough/ bd fabrication in Medford oregon
@carlosfsanchez6273 Жыл бұрын
When’s the next episode coming out?
@rosinsautofab1956 Жыл бұрын
Next week thanks
@othoapproto960313 күн бұрын
is a full float front axle possible?
@rosinsautofab195613 күн бұрын
If you wanna get technical, the front axle would be considered a full float as the shaft is not riding on the wheel bearing
@calholli6 ай бұрын
Instead of wasting all that tape next time.. Just rough cut some cardboard so that it's over sized and fits around it---- then you can use a few pieces of tape to fill in the gaps along the edge for the detail; then just transfer that onto your next carboard as the final template. This way you waste minimal tape.
@rosinsautofab19566 ай бұрын
Tape is cheap and easier to work with cover the whole thing and then take a sharp razor blade and just trim out your shape and then the tapes transfers to your material and sticks to material
@calholli6 ай бұрын
@@rosinsautofab1956 I agree.. Just fill most of your "tape" bulk in the center with cardboard.. or newspaper or something.. Just like when painting a car-- you don't cover the whole thing with tape--- you use paper or plastic and just tape the edges.
@rosinsautofab19566 ай бұрын
Tape is cheap…. larger templates we use dollar store poster board
@calholli6 ай бұрын
@@rosinsautofab1956 I'm too lazy to go to the store and buy poster board. .... cardboard it is then. :)
@rosinsautofab19566 ай бұрын
Ya being lazy only gets you so far, takes 5 min to swing into the dollar store on your way to work etc… poster board gives me nice sharp lines and transfers better to my material, I hate thick cardboard and a cereal box is only so big, thanks for watching and I appreciate the comments 👌
@brenttblair876810 ай бұрын
Dude I get motion sick trying to watch that. Try again, that sucked.
@rosinsautofab195610 ай бұрын
Maybe you should consult your gynecologist
@brenttblair876810 ай бұрын
Haha, guess you don't care about quality. Literally, constructive criticism directly from one of your consumers. Which I could have surmised from that abortion of a truss you attempted. Thank God I can spend my time elsewhere, you are low of skill and low of character.