NUX MG30 SIGNAL BLOCKING (ON/OFF SIGNAL (PEDAL) USING MVAVE CHOCOLATE MIDI CONTROLLER

[@cristianoalmeida5388]

omg, this is just the video I was looking for. Thanks for sharing my friend!!!! Greetings from Brazil

[@dreamsdontexist]

thank you sir

[@prevdiary06]

wow

[@normandst-aubin3571]

I have it turning blocks ON/OFF but it re-assigns the block's effect to the first one in the bank of blocks. For example, if my 1A rig has a Tube Screamer as my EFX block, when I press my A switch on the Cuvave, it will turn ON the Boost pedal instead of the Tube screamer... Any suggestions? Thanks!

[@joymelynjumaquio1720]

Up dito... pag sinet ko sa tube screamer, pag switch on ko bumabalik sa boost pedal... pano po maseset sa specific efx pedal na gusto mo? Salamat po!

[@genmar27]

Can you post an update for this issue. I'm having the same problem here. Everytime I turn it off/on using the Chocolate, it reverts to the first effect on the list instead of the one I assigned

[@johnefmargerona2934]

Does this works on the latest update?

[@yujrondina5260]

bossing kaya po ba mag on off ng tuner sa mvave chocolate?

[@BigMacGuitars]

ang naturn of at on lang ay iisang pedal hindi yung signal block mismo meron po bang para sa buond block

[@weeklykidstv716]

ito kailangan ko sir thank you

[@normandst-aubin3571]

Awesome! Will this work for all banks on the nux? Like will it always switch ON/OFF the block no matter which bank your in (1A 1B 1C, and so on until 32D)? Many thanks in advance my friend! Very good simple video to follow!

[@dreamsdontexist]

yes sir depends on your config

[@normandst-aubin3571]

@@dreamsdontexisthey thanks for replying! I followed your instructions but I couldn’t get it to work. Are there pre-existing settings I need in the nux or the cuvave? Also, why did you say to use « 1 CC X 64 or 84 » in bank B? Is that a cuvave code or a nux code? Sorry for my many questions! Thanks again if you choose to answer them!

[@joeysevilla8758]

Sir, san galing yung numbers sa data 2 na field?

[@jackupasturious]

meron yata kulang sa config settings ko, kakadating lang ng order ko na mvave, sunundan ko mismo ang instruction mo, pero nothings working, meron ba ko kulang, need help, thanks in advence

[@JunelBejec]

ano pwedde code po on of ng send return

[@weeklykidstv716]

anu ba ibig sabihin ng 64 at 84 dun sa data?

[@makoy2311]

Sir di po ba yung specific effects lang na oon off hindi yung mismong signal block?

[@weeklykidstv716]

yung specific effect ang na ON and OFF nya kahit nakasave na babalik dun sa kung anu yung na On at OFF nya, saken yung FLANGER effect yung na OFF at ON nya

[@makoy2311]

@@weeklykidstv716 Hindi yung mismong signal block sir di kaya yun? wala talaga sulosyon sa ganun eh nu yung specific effects lang talaga, hinahanap ko kasi yung mismong block talaga tulad sa nmp2 na control sir

[@sedrock]

Ser pag nag palit ba nag patch gagana paren yung signal block?

[@dreamsdontexist]

yes po

[@weeklykidstv716]

panu mo natutunan to sir?

[@joymelynjumaquio1720]

Nakuha ko na kung pano iset kung anong efx ang gusto mo, example efx then TS9, kaso pag switch on ko ng signal block ng efx, kung ano ang default na setting ng knobs ay dun cya bumabalik kahit isave mo ung gusto mong setting... eto naman ang problema ko ahahahaha

[@johnefmargerona2934]

Solve mo na ba to? For TS9 effects Bank A 1 CC 2 5 Bank B 1 CC 2 64 ang problema naman neto. kahit iset mo yung parameters nung T Scream sa gusto mo, bumabalik sya sa default after off then on.

[@silverioeltagondejr.8531]

On nyo po ang para flow sa global setting

[@johnefmargerona2934]

@@silverioeltagondejr.8531 I'll try this po.

[@weeklykidstv716]

mas ok sir kung ON and OFF ng signal