Refill Brother LC223, LC225, LC227, LC229, LC203, LC205, LC209, LC233, LC235, LC239

[@AndrzejKowalewski]

Just refilled yellow cartridge. Worked great. NO chip reset was necessary. Thank you.

[@catheyhawes9958]

Thanks for this video. I was struggling with a region-locked printer and was about to use your video to help me extract the ink from one cartridge so that I could inject it into the other however before I’d finished breaking the cartridge up I realised that all I had to do was swap the front pieces and the printer would be happy again. Thanks!

[@octopusoffice]

Thankf for Your feedback and explanation - sounds You did some serious cartridge surgery! Happy to read the patient is well!

[@Fridelain]

IF after refill it stills complains it's empty: (COMPATIBLE CARTRIDGE) TAKE OUT THE SMALL CIRCUIT BOARD. YOU MAY NEED TO LEVER A PLASTIC HOOK AWAY WHILE YOU PRY IT OUT, OR CUT FLUSH SOME PLASTIC RIVET, EITHER WILL HOLD IT IN PLACE. THERE IS A SMALL BUTTON CELL BATTERY ON THE OTHER SIDE, INSIDE A METAL HOLDER. SOME OF THE METAL WILL BE BENT TO HOLD THE BATTERY IN. FOLD IT BACK. PUSH THE BATTERY OUT FROM THE OTHER SIDE WITH A PIECE OF WIRE OR TOOTHPICK. KEEP IT OUT A FEW SECONDS. PUT IT BACK IN. MAKE SURE THE NEGATIVE SIDE WITH THE CIRCLE POINTS TOWARDS THE CIRCUIT BOARD, AND THE POSITIVE SIDE, THAT EXTENDS TO THE SIDE WALL OF THE BATTERY, THE ONE WITH THE TEXT MARKINGS, TOUCHES THE METAL CAGE. THIS WILL RESET THE CHIP. THEN PUT THE CIRCUIT BOARD BACK ONTO THE CARTRIDGE. IT SHOULD WORK NOW.

[@octopusoffice]

Hello Fridelain, thanks for Your contribution. It´s worth to give this a try with alternative cartridges. We learned from our own tests that removing the battery from such chips - makes the chips´brain forgetting everything - after setting back the battery every information on the chip is deleted. Maybe this does not apply to all alterntive chips - that´s why we say it is worth to try....

[@waswat]

Beautiful video, thanks a LOT. (Great & clear voice btw)

[@octopusoffice]

Thanks for the positive feedback :)

[@ibrahim.salfi.]

Best of luck in your new job Thank you very much

[@octopusoffice]

Thanks!

[@pierrejoubert7754]

Nice, clear, easy to understand video. Thank you.

[@octopusoffice]

Hello Pierre, thanks for Your nice feedback!

[@Aideo]

Thanks for uploading this fantastic video. Can you upload one with the LC401 model please?

[@octopusoffice]

Hello Aideo, thanks for Your nice feedback 👍🏻 The LC401 cartridges have ink chips build on. For these chips it is necessary to have the suitable chip reset device - this one is still missing at the moment (status March 14th 2023) - we have our eyes on the market and as soon one of our suppliers will have this ready we are going to set up a solution. Without the resetter You can fill up ink into the cartridge but the printer refused to go on printing with this cartridge as it "thinks" the cartridge is still empty due to the chips´ empty status...

[@Aideo]

@@octopusoffice Thanks for the reply..You are awesome!

[@octopusoffice]

You are welcome - we are looking forward to get the LC401 solution ready....

[@peterhancock8011]

I have refilled a LC223, but the printer still thinks it is empty. What could be causing this?

[@octopusoffice]

Hello Peter, filling up an empty cartridge with ink does not restore the displayed ink level back to FULL. With sufficient ink inside the cartridge You should be able to start print jobs despite the empty status.

[@vimelbudhdev2593]

Hi, I purchased a set of ink refills from yourself a couple of months ago. I filled the yellow ink cartridge exactly on the way instructed for the first time, however the printer does not recognise the ink has been filled and says it’s empty. I have a brother printer LC223. Any advise would be much appreciated, Many thanks

[@vimelbudhdev2593]

It’s a brother MFC J5320DW Printer

[@octopusoffice]

Hello Vimel, the cartridge LC223, that You are trying to refill, is an original Brother cartridge or a cartridge made by an alternative supplier?

[@vimelbudhdev2593]

Hi thanks for your reply, it is an original brother cartridge. I hope that helps

[@flybobbie1449]

What's the point in having the float level indicator and a chip. All that is needed is the float and a light sensor to tell the printer ink level is low.

[@octopusoffice]

Thank for the question. We are with You in that point - but this solution would make it too easy for You to use the cartridge again - Brother® does not really want that :) The chip is a clever way to make customers buy original cartridges only as long as the alternative cartridge manufacturers are working on an alternative chip solution.

[@martinl.4711]

Warum so kompliziert? Wenn ich von der Seite reinsteche, reicht wegen der schönen ebenen Fläche an der Seite ein Stück Tesafilm zum Zukleben, oder etwa nicht? Wenn ich einen Denkfehler mache, bitte ich um Hinweis bzw. Erkärung. Vielen Dank. Dennoch tolles Video, danke dafür.

[@andibuttri]

Also you even demonstrated the correct use of the apostrophe - as in "video's end" - putting most brexit commentators and our grocers to shame! ;-)

[@octopusoffice]

You made my day - early on Monday morning already. Thank You for cheering me up...

[@drathir55]

Hello, great material ! I have two questions about filling - whether cardridge should not contain air (vacuum)? Is the filling process requires resetting the chip?

[@octopusoffice]

Hello, thank You very much for Your question. 1.) The inner ink tank always contains some air when the proper quantity of refill ink has been filled. The more ink is consumed by printing the more air is in the inner ink tank. The air replaces the consumed ink. 2.) You can also use such a refilled cartridge WITHOUT resetting the chip. Then You have to print without proper ink level information. The ink level information for such a refilled and NOT RESET cartridge will be deactivated.

[@jimihenrik11]

Just did it and it worked fine. Now I'm wondering if i need to clean the syringe and how to do it. Will it get constipated?

[@octopusoffice]

+jimihenrik11 It is sufficient to rinse the syringes using water after use. Pull the plunger out of the syringe´s body and eversthing can dry properly.

[@bitbitesabc7248]

hi, thanks for the video. This is compatible also for the LC103 cartridge? do you have any further printing issues later apply this technique?

[@octopusoffice]

+bitbites abc LC103 is the previous cartridge model series. You can apply the method shown in this video also on LC103, no problem. Beside the way of refilling please make sure to use a proper ink suitable for LC103 cartridges.

[@vincenzovitello4578]

The cartridge don't need reset the chip?

[@octopusoffice]

There is a resetter available so You can reset the original Brother® chip BUT You do not must: You can keep on printing with a refilled cartridge and a non reset chip on it. In this case the ink level information will be deactivated.

[@dennisgalante6942]

i only print text and therefore need only black ink. The other colors dry out (?) and so i still cant print. can i fill the color cartridges with black ink

[@octopusoffice]

Hello Dennis, it depends a bit what kind of ink you are using for Your black cartridge. In case it is a black pigmented ink it will not work properly in the other cartridges as they are running on dye base inks. The worst think that can happen is that the nozzles for cyan, magenta and yellow will be blocked. But if You really do not need these colors You also do not need those nozzles .

[@davow8]

How can you refill an LC3319XL cartridge? I cannot find an air release valve.

[@octopusoffice]

Thanks for Your question. The LC3319 have a different design layout. Actually You can push the refill ink into the cartridge by using the ink port. We have video tutorial that shows the extraction of the ink out of an original Brother cartridge - using that method the reverse way enables You to refill ink into Your cartridge. kzbin.info/www/bejne/o4XbYpyKgaZmias Our problem is at the moment that Brother does not support anymore that You can keep on printing with an empty original chip - that means You can refill Your cartridge with suitable ink but the printer will not accept that cartridge for further printing :(

[@davow8]

@@octopusoffice thanks for that. I managed to work that out with a standard syringe minus the needle. Works easy. Can you cold start your printer to override the chip count?

[@octopusoffice]

@@davow8 Thanks for the feedback and great to read You have found a tool solution. So far we have not been able to find a way to get the printer back to work with the refilled original cartridge - sad story! We have been digging through the well hidden service menus - still no success...

[@davow8]

@@octopusoffice Just replaced the genuine refilled cartridge. Worked no problem. I have a 1 month old MFC-J6530DW.

[@octopusoffice]

@@davow8 Interesting information! From where do You write to us? According to some rumors in the market there are differences in the behaviour of Brother printer models in different geographical regions . US printers do different from Europe region printers some tales say ...

[@simaolima5495]

Será que funciona nos cartuchos da Brother J6935dw? Does it work on Brother J6935dw cartridges?

[@octopusoffice]

Brother J6935dw uses LC3217 / LC3219 cartridges - they are a different story - this tutorial does not work for them. We will have refillable cartridges for LC3217 / LC 3219 soon.

[@beedslolkuntus2070]

cooooollll. which hp or similar brands used a sensor that ACTUALLY checks the ink. Basically, brother is selling "ink tank printers" in theit normal printer line up. they made it a whole lot easier for us to make it ciss

[@octopusoffice]

Thanks for Your feedback! Nowadays basically all inkjet printers are equipped with technology creating information about the ink level status. We like the printer models that have build in ink tanks that can be filled by bottles - they are available from Brother, HP, Canon and Epson....

[@beedslolkuntus2070]

@@octopusoffice and out of the brands you have listed, HP smart tank 500/600 series have that tech. they can detect the ink in the printer.

[@jefferythornhill8735]

Thanks for the video Octopus... I do have a question, I have been refilling LC-201 and can not find ink amounts for these. Would the ink amounts for LC-201 be the same as the LC-203??

[@octopusoffice]

Hello Jeffery, the LC-201 is actually the smallest version of the cartridge series LC-201, 203, 205, 207, 209. So the original amounts of ink are 7 ml for black LC-201 and 4 ml for cyan, magenta, yellow LC-201.

[@thornhillorama]

+OctopusConcept Really??!! Wow that is low amounts.. Since I didn't know the amounts I was treating them as a LC-203... I hope this is ok.

[@octopusoffice]

Let´s hope the best. Usually Brother is using lower page yield by filling less ink to sell the cartridges for a lower price. But in some cases the physics of the cartridge do not work well if You fill more than the original amount of ink. Keep an eye on Your prints, then You should be fine. When drops appear on the prints it may be better to remove the excess ink from the cartridges.

[@ow5445]

Hi How to seal the cartridge ? what liquid or material did you use ?

[@octopusoffice]

Either You use a drop of hot glue, which can be removed easily for the next filling again. Or You have a suitable rubber plug available.

[@ow5445]

Thanks for that what have you used in this video ?

[@Vinceb318]

I refilled using this method, but the printer doesn't seem to detect that the cartridge is full and is displaying as empty, so it doesn't allow any printing and for some reason only the black ink cartridge is being detected. Any suggestions?

[@octopusoffice]

+waniushka As long as You have not reset the original cartridge´s chip using a suitbale chip resetter, the ink level stays at the status empty. When setting back the refilled cartridge into Your printer the printer asks if You have changed the cartridge. You have to answer this with YES. Then the ink level information for this cartridge is deactivated. The process does not work for alternative cartridges.

[@Vinceb318]

+OctopusConcept I did exactly that, but the printer still thinks the cartridges are empty and doesn not allow any printing. Do you think the resetter would solve this issue? And what do you mean by alternative cartridges? Thanks

[@octopusoffice]

Alternative cartridges we name cartridges not made by Brother. These cartridges do not support continued printing with a refilled cartridge due to their chip, which is not made by Brother too.

[@Vinceb318]

+OctopusConcept Oh I see. Well these cartridges came with the printer, so I assume they are made by Brother. Do you think the resetter would help in this case or is the problem somewhere else? Thanks

[@octopusoffice]

Thank You very much for these additional information. These cartridges are called setup cartridges. They should are original Brother cartridges. Some of our customers told us that setup cartridges did not work refilled in their printer, but we were not able to reproduce that result as our setups also worked refilled in our printer. We recommend to have at least one set of regular (non setup) Brother original cartridges.

[@Marco-ib4ql]

Does this work with Brother MFC-365 printer?

[@octopusoffice]

Hello Marco, thanks for Your question. What cartridge models does Your printer use?

[@hoijao8132]

but if you don't have to reset the chip , then you don't know when the ink end and the print head may burn if over hit . and the chip resetter is very cheap now , so I suggest buy one for reset need if who want printing photo or documents smooth :-)

[@octopusoffice]

Hoi JAO Thanks for Your comment. We fully agree with You. But this decision has to be made by every customer itself.

[@ZainYMijbil]

Hi and thank you for this helpful video, I have a problem with the black cartridge. Every time I fill it, I can print almost 50 sheets and then the printer gives the note "Not enough ink to keep print quality". I filled many cartridges with many different levels, but the problem persists to happen. Is there anything I can do to avoid this problem please? Many thanks and best wishes.

[@octopusoffice]

Thanks for the question. Do You use a refill ink specificially for the Brother LC22x cartridges series? In case some of the physical characteristics of the used refill ink do not match the printers´ requirements this message may show up.

[@ZainYMijbil]

@@octopusoffice Thank you very much for your response. Yes, I do use a special ink for the printer. However, I have noticed that you closed the hole after filling the cartridge. I think the problem is the pressure inside the cartridge, because I did not seal it. I have checked recently, and the printer's still working fine. I hope it will last of a quite reasonable time. Cheers and best wishes.

[@bobbymois]

Sehr schönes Video Ist 6 ml die maximal Menge die man aufüllen sollte oder kann man sogar mehr machen ?

[@octopusoffice]

Danke für die positive Rückmeldung. Füllmenge 6 ml bezieht sich auf LC-223 Patronen, bei LC-225 kommen 12 ml rein, bei LC-227 = 25 ml und bei LC-229 passen 50 ml. Das sind die originalen Tintenmengen, die auch Brother bei der Paroduktion einfüllt. Theoretisch passt immer ein bisschen mehr rein, aber Überfüllung kann dazu führen, dass die Patrone physikalisch (Druck + Entlüftung usw.) nicht richtig funktioniert. Aufgrund dessen empfehlen wir die Originalfüllmengen :)

[@bobbymois]

Danke für die schnelle und ausführliche Antwort :)

[@jordanliswid562]

hello. can i do this method with LC40BK? thanks in advance.

[@octopusoffice]

Thanks for the question. The housing of the LC40BK might be a bit different and the fixing of the housing to the inner tank too. But basically it is not impossible to figure out how to get the housing off. The inner tanks for the ink are quite similar to each other, so find a suitable spot for the fill port and You can do as shown in our video.

[@italo9260]

please can u show how to refill Brother LC1100

[@octopusoffice]

Please check the following link: www.octopus-office.de/info/en/ink-refill-instructions/ink-refill-instructions-for-brother/ink-refill-instruction-for-brother-lc-980-lc-985-lc-1100/refill-instruction-for-brother-lc-985/ It demonstrates the refill of a Brother LC-985 cartridge which is similar to LC-1100. We hope that can provide sufficient help to You.

[@anonuser]

This makes no sense. Everyone else just pumps the new ink through either the existing air hole or lower ink hole, yet you choose to make another hole. Sorry, I don't understand why.

[@octopusoffice]

Thank you for sharing Your honest opinion. We are aware of the alternative ways to get ink back into these cartridges. Some of our customers did not like the other ways or ecperiences difficulties using them. For those we show another possible way.

[@OkiDingo]

was that yellow or red?

[@octopusoffice]

Hello Dean, do You mean the color of the refill ink?

[@WaschyNumber1]

Dein englisch ist nicht schlecht, manche anderen firmen sprechen viel schlechter englisch :-) sehr gutes video, muss man eigentlich bei den Patrone auf unterdruck oder sowas achten wie bei anderen marken, wo man extra noch unterdruck nach dem wiederbefüllen erzeugen muss?

[@octopusoffice]

Danke für das Lob! Bei der Befüllung mit Spritze und Kanüle ensteht innerhalb der Patrone kein Über- oder Unterdruck, vorausgesetzt die Einfüllöffnung ist größer als der Kanülendurchmesser. Während des Betriebs im Drucker erfolgt der Druckausgleich über die obere Belüftungsöffnung an der Patrone.

[@MahendraSingh-sq4ud]

what about LC201 XL ?

[@octopusoffice]

Thank you very much for Your question. You can apply this refill method on LC201 cartridges too. But according to my knowledge the LC201 exists as standard yield cartridge only. The ink quantity for LC201 black is 7 ml and the ink quantity for LC201 cyan, magenta or yellow is 4 ml.

[@lazarussmith01]

As low as the price's Are for NEW ink cartridges on eBay, AND taking a chance of burning the print head if the Brother All in One, THINKS the Cartridge's or Cartridge is full but not, Than I think it would be best to use new and just have to pay a little more than to take that chance and maybe even make a mess. I like saving money just like anyone else, But I don't want to be ordering parts to install when I'm really not sure how easy that is ether.

[@octopusoffice]

Thank You very much for contributing on that topic. Unfortunately a lot of the NEW alternative inkjet cartridge products have a quite unreliable quality inkwise and chipwise - in our humble opinion. So refilling the originals requires a bit of practice, that´s right. At the same time working with original cartridges also pays respect to the original manufacturers intellectual property and rights.

[@PATWO]

Where can i buy the ink?

[@octopusoffice]

Thank You for Your question. Ink is available at www.octopus-office.de/shop/en/refill-supplies/ink-refill-supplies/miscellaneous-refill-supplies/233/ink-set-brother-lc-223-lc-225-lc-227-lc-229-lc-12e

[@PATWO]

Thank very much for the attention :)

[@octopusoffice]

You are welcome :)

[@youtubecommentor6807]

Thanks for helping me with the printer scam market

[@octopusoffice]

Thank You too for Your positive feedback! Please do not let printers make You feel frustrated :-) Learn about alternative solutions - limit Your print outs ...

[@jantay5122]

Can you do one for lc3011 ?

[@octopusoffice]

Thanks for the question. Actually yes. But it depends on global region if Your printer allows You to go on printing with a refilled cartridge LC3011 that has been shown empty in Your printer - no other choice than just ry.

[@talsmadja731]

Thanks! Very helpful !!

[@octopusoffice]

Thanks for Your positive feedback!

[@ememiranda598]

and the chip?

[@octopusoffice]

There is a chip resetter availabel which you can use the reprogramm the chip on the cartridges. But luckily Brother still provides the opportunity to keep on printing with an "empty" chip. You will not have any ink level related messages anymore for that cartridge but You can print if there is sufficient ink inside.

[@davidpatterson2178]

Can we hear you? what with the whisper?

[@octopusoffice]

Hello David, thanks for the feedback - I am trying to improve constantly on sound and on equipment 😊

[@andibuttri]

really helpful thank you (p.s. sorry about brexit and so on)

[@octopusoffice]

Thank You very much for the positive feedback. ( no apologies necessary - people in possession of common sense will find ways to stay connected in the future too)

[@vinceramdhanie4210]

so everytime we have to drill hole and fill then seal it bk,fuck thats alot of work if you have a business

[@octopusoffice]

Maybe to think of the costs to buy a new orignal cartridge each time motivates a bit... :)

[@parvatanenivenugopal]

Good😊

[@octopusoffice]

🙂 thx for this positive on the point feedback

[@TeoricoARB]

Thank You

[@octopusoffice]

Same to You!

[@ramon9216]

No habla nada de resetear el chip.

[@octopusoffice]

También es posible imprimir con un cartucho de tinta rellenado sin reiniciar el chip.

[@ramon9216]

El chip cuenta las páginas ? Cuál es el fin concreto del chip?

[@ramon9216]

Estos cartuchos no llevan chip ?

[@octopusoffice]

El chip identifica el cartucho de tinta contra la impresora.

[@octopusoffice]

Cada uno de los cartuchos de tinta tiene un chip.

[@Stein_NZ]

Cheers

[@ClaudioParraGonzalez]

completely unnecessary. you can fill them through the same place where the ink normally exits the cartridge

[@octopusoffice]

Hello Claudio, thanks for taking the time and providing Your thoughts about our tutorial. We are happy to read that Your way works fine for You. Quite a number of our users asked for the tutorial with refilling by applying a hole into the cartridge body. The way to refill the cartridge by the ink outlet and paying attention to release the built up pressure at the same time was to much to handle at the same time for this user group.