Odie's Oil: How to Apply Odie's Universal Oil

James goes over a step by step of how to apply Odie's Oil correctly to get a beautiful, durable, and safe wood finish. To see more videos with Odie's Oil or to check out more projects done with Odie's Oil, go to the links below ⬇️🌿🪵
Odie’s Oil uses the finest oils and waxes produced by nature to protect your wood surfaces. Our products are food safe and contain no toxic solvents, driers or hardeners. Check out our product lineup or learn more at www.odiesoil.com/
And follow us on social media to see more beautiful pieces protected and beautified with Odie's Oil:
/ odiesoil
/ odiesoil
www.odiesoil.com/

[@paulmorgan5841]

OK if I’m being super picky, the instructional video is a little too sales pitchy, this is the elixir of the gods, it can do anything and it’s fool proof etc. but - - - he’s basically right. I used Odie’s on a couple of restoration projects of late, and I can’t for the life of me now understand how come someone didn’t figure this out sooner. This is by far and away the best hand rubbed finish you could apply to any project. And for many reasons. And I’m an old danish oil, and Maloof mixture, hand wax, and even shellac guy. Occasionally lacquer. This stuff is the real deal.

[@andrei.8375]

@paulmorgan how long would it need to dry before you can send the table top to a customer ? Thank you

[@evelynmueller6523]

I love using this product with my projects!

[@ManWithGoodHands]

Thank you so much for making this finish. I was FORCED to abandon my Rubio Monocoat and Osmo finished when I needed to make a food friendly kitchen mallet. Odies was my choice and now I’m using it on EVERYTHING. Holy crap it’s nice to work with and it smells so good.

[@Odiesoil]

Thank you for choosing Odie's!

[@jori7398]

This is so very helpful! Today is my first Odie’s adventure after restoring an old French desk, which I had zero experience to do. 😅 It’s also exciting for me to have found a product that’s natural. I’ve got autoimmune disease so need to be really careful with chemical things. What a life saver Odie’s is! You are absolute aces in my book, Sir. Wishing you a wonderful and blessed New Year!

[@HeathenHammer123]

I just used it for the first time yesterday! LOVE THIS STUFF!!!!! works so well

[@Odiesoil]

Thank you for your feedback!

[@antonoat]

Looks like an amazing product, good exercise too! It seems I can buy it here in the UK, I'm going to have to try and buy some! Thanks for the film, and the product.

[@roy_8693]

BUFF OFF! I love it! Seriously though, I have a full Odies kit (from Infinity Cutting Tools) on the way. I watched their video and bought it on the spot. I will be taking advantage of your tech support team when it comes time to apply it to the live edge slab I'm using to make a dining room table. Thanks for the info!

[@zebracakes7342]

Odies is amazing on sanded epoxy for a epic satin finish. Thanks bro!

[@wessmith3181]

Thanks for this video! Merry christmas

[@mvecellio1]

Great instructional video. I just made a bowl and finished it with Odie's Oil. It is by far my favorite food safe finish. Thanks.

[@Odiesoil]

Good stuff!

[@KarlBunker]

News flash: _All_ contemporary wood finishes are food safe when cured. But yeah, Odie's oil is good stuff.

[@innointelsolutions]

nice

[@RedRockingBird]

I can’t wait to test this out

[@Odiesoil]

You’ll love it!

[@underthetracks]

Build a statue of that man. He invented the best finish ever!!!

[@Odiesoil]

Thanks! At Odie's we have to agree. We love your comment:)

[@monmixer]

Your product makes great satin finish guitars

[@Odiesoil]

It absolutely does! Luthiers were some of the first woodworkers to embrace Odie's.

[@KaragioElena]

I love how James explains the whole process with Odie's Oil. I have used it to all my restorations and I simply love it! I have one question, can the merlon pads be washed and reused or do I have to throw them away after each use?

[@Odiesoil]

No, can't be washed and re used. Only can be stored for 2/3 days in a ziploc bag. Dispose of them safely! if you don't have a safety container wet them and after dispose it!

[@pg5604]

@@Odiesoilthe towels must be disposed or can I wash and reuse! Loved the instructions - just ordered my 1st jar. Thank you!

[@ralphbrown6636]

IT IS AMAZING HOW MANY PROFESSIONAL WOODWORKERS DEMONSTRATE AND REVIEW ODIES OIL WITHOUT BOTHERING TO FOLLOW THE MANUFACTURER'S INSTRUCTIONS. THEY THEN COMMENT HOW IT DOES NOT HOLD UP OR LOOK GOOD OVER TIME. I AM AN AMATURE WOOD WORKER BUT BY FOLLOWING THE INSTRUCTIONS IN THIS VIDEO I HAVE ACHIEVED BEAUTIFUL RESULTS. The only question I have for the manufacturer is how fine of a grit can I use on DOUGLASS FIR and still get the desired result. I am waiting to finish a douglass fir project because I have heard that fir can be challenging to finish if you sand it too fine (perhaps I am wrong, but if someone can answer this I would appreciate it).

[@Odiesoil]

What grit were you thinking of sanding to? also what type of project and what is your vision for your project? Let us know so we can give you some pointers. Also feel free to talk to one of our tech support people www.odiesoil.com 850-695-2055

[@lowerycustominteriors]

Very informative video. In video you mentioned you can touch it right after buffing, in the comments someone asked about spilt wine your reply was after being ’fully cured’. What is the ‘fully cured’ time?

[@Odiesoil]

yes, you can use your piece straight away, however, you need to allow it to fully cure (like with any other product on the market) for 3/5 days before you expose it to liquids.

[@larryblair6914]

Sorry if I missed the answer to my question in one of the comments below:what is the cure time after a coat of odie's? Is the cure time the same for subsequent coats. I'm a new user and really excited about what it can do!!!

[@larryblair6914]

found my answer: recoat next day and cure is 3-5 days

[@Stu81]

Just got some, I think the jar needs a warning label to stop the wife spreading it on her toast it smells that good.

[@Odiesoil]

Ha Ha - Please don't eat the Odie's

[@topsaw]

I love this stuff at my home. I teach high school woodshop and when we use it in class, we use way too much and it gets too expensive

[@Odiesoil]

Are you buying Odie's direct from us?! We always offer wholesale account for schools! Odie's is one of the cheapest and durable products on the market with a cost of 22 cents for sf on oak!

[@topsaw]

@@Odiesoil no, but I will thank you

[@Odiesoil]

@@topsaw We would love to help! We also offer trainings and swag! Please send us your request to [e-mail]!

[@BradsWorkbench]

If you left it on for 12-24 hours would you still be able to buff it off or does it have to be buffed off around an hour?

[@martindickerson5235]

Hi I’ve recently purchased your oldie oil wow what great oil it is once I’ve use the oil do I then put a oldies wax on to make it washable as I want to use it on some really nice cutting boards look forward to hearing from you also great video

[@Odiesoil]

Can you please give us a call 850-695-2055

[@todayfeelz5050]

Did you get an answer? Would also be interested

[@martindickerson5235]

@@todayfeelz5050 hi the oldie does not last on cutting boards made from certain hard wood more porous wood it soaks in a lot further and last longer having said this I recommend it it’s fantastic stuff I also think it’s the best on the market

[@todayfeelz5050]

@@martindickerson5235 thanks for the answer, would you have any recommendations for cutting boards?

[@martindickerson5235]

@@todayfeelz5050 hi this is martins wife here texting on behalf of my husband he was admitted in hospital last night as soon as he’s out and feeling better he will answer your question

[@matthonea7939]

Hi there! Can you use some type of buffer for applying the initial oil? I have limited strength so it was quite difficult to do this on my first project but I liked the finish so well that I want to continue to use Odie’s.

[@Odiesoil]

Yes, you can! You can use a non woven pad which will stick to any hook and loop disc on a palm sander. Apply sparingly, being sure not to over apply the oil during application. Do not use the machine to remove and buff off the excess though, do this by hand with a 100% cotton terry towel.

[@walterrider9600]

thank you. i am an old geezer just new to wood working . does the oil protect the table tops i used a tunge oil varnish on a desk top . results looked great new but after about 3 yrs looks like i need another finishing .

[@Odiesoil]

Odie’s Oil will help restore and freshen up an already finished piece but the previous finish will be the barrier between Odie’s and the bare wood. If the previous finish is prone to failure, Odie’s can only help so much in the long run. To get the full benefits of our finishes we recommend to apply to the bare wood.

[@brauckstar]

I am restoring 100 year old mission style oak columns. I used Odie’s & loved the finish. The wood drank up the oil. So much so that when I buffed it off there was little residue. Does this mean I didn’t use enough?

[@Odiesoil]

You do want to get the wood to the point of full saturation (to where no more oil will be accepted) for soft woods, old dry wood, or punky wood it’s best to do multiple light coats with a day between coats until the wood becomes fully saturated. It’s still important to do a proper buff off after every application to ensure any excess or residual oil on the surface gets removed.

[@TWC6724]

Was there a finish on this wood before you applied the oil? It looks like it has s great sheen to begin with.

[@Odiesoil]

No finish was on this surface. It was just a properly sanded and prepared surface. The better your surface preparation the better your end results will be.

[@CovChannel]

Can confirm. I have Jatoba sanded to 3k and it reflects well with zero product.

[@jerrymcswain2656]

Fixing to do a cedar table with beautiful color.... will this change the color ??? Others I've used has .

[@Odiesoil]

No, Odie's doesn't change the color and is not ambering, however will offer like a wet look effect to the wood, we always recommend to run a test piece

[@KaragioElena]

I used Odie's oil to refinish my midcentury danish chair. I followed all the steps showed in the video. I love how rich the color of the wood became but even though I buffed, using a towel, I don't see the sheen. Any advice?

[@Odiesoil]

The sheen is primarily dictated by the surface prep. The higher you sand the higher the sheen. However, you can step the sheen up once you’ve already finished your work. Please check out our latest video just posted!

[@dovechaser2007]

I have 1000 sqft of white pine tongue and groove porch ceiling. Would this be a good product to finish? Hoping to maintian the white color and prevent too much yellowing. There is no way I can sand to 400 grit or buff as thoroughly as these videos show! My arms still hurt from install!

[@Odiesoil]

dovechaser2007 hello, yes Odie’s will work great only one coat you will need, you don’t need to sand, you sand only if want to get a gloss look, are oil it is translucent will offer to the wood a wet look type, is not yellowing

[@gonzo1863]

Just got my first jar today, where do I store it? My garage gets pretty hot in the summer.

[@Odiesoil]

Awesome! We are excited you’re trying Odie’s! It’s best to keep out of direct sunlight. It should be fine in your garage but you can definitely store in a cabinet in the house. All natural and completely non toxic!

[@d-m-c1358]

Did you apply any coat before this Odie Oil because the slab looks nice & shiny already? This Odie Oil coat is like the topcoat to protect the finished surface of the wood? I am very new to wood so I would like to ask many things before using thanks

[@Odiesoil]

Please send us an email to [e-mail] or give us a call, we are happy to help 850-695 2055, meanwhile you can check our faq page www.odiesoil.com/faq/

[@Odiesoil]

[e-mail]

[@Odiesoil]

Tommy Cuong Do higher you sand higher the sheen. In actuality you don’t have to sand past 800 or 1000 to get a very high sheen. It’s more about the quality of your sanding. A good finish sander is needed along with quality materials. Take your time and be thorough... do not skip any grits and you will find it easy to get a high sheen.

[@markcorso1262]

What kind of protection does this finish provide? ie: Is it okay for wet glasses on a table, etc. Also, how do you handle porous woods?

[@Odiesoil]

After the full cure time, it is completely waterproof! It is also stain resistant, provides UV protection, stabilizes the wood, and more. Odie's works great on all species of wood, porous or not.

[@jeepersmurphy2570]

@Running Red Fox Use your intuition. If you're using a low to no building finish like these oil/hardwax products, porous woods are better used with a pore filler. If you're just slapping lacquer or poly, just let er rip if that's your style. Price is what you pay and value is what you get. Doesn't get much better value than these simple to use oil/hardwax finishes.

[@jaa2412]

Hi Can I buff the odie's oil finish with a polish compound to get a mirror shine? in that case, how much coats of oil are needed to protect the color (in my case I used dyes) Thanks in advance

[@Odiesoil]

hello, you can get a high gloss with Odie's oil if you sand high, usually up to 800. One coat is enough, however more coats more layers of protection, you can add more protection and beautify your piece by following with the butter or wax

[@chicomarie1]

I have white oak with a dark oil finish that has no sheen. Can your product work without creating a shiny surface? If yes, how should it be applied?

[@Odiesoil]

Hello, higher you sand higher the sheen, for a Matt look you need to sand 220 and below. You call us for more info 850-695-2055, or send an email to [e-mail]

[@eladsinay6914]

you mentioned going up to 800 grit sanding. im new so can you tell us the grits you would run thru to get up to 800 in order please

[@Odiesoil]

hello Elad. It is very important to not skip any grit, because the oil will bring out all the scratches, therefore the surf prep is very important and on your last sanding check your piece in a good light for any potential scratches, please give us a call for more info please give us a call 850-695-2055

[@JohnVeitch1]

I'm looking for an oil like this that I can put on a oak table that I'll leave outdoors on my deck, well this hold up against sun, rain and snow?

[@Odiesoil]

For more protection and durability we do recommend mixing into oil one of our pigment colors, allow to cure for 3 to 5 days, and follow with a clear coat of the oil and will hold against sun, rain, and snow. Please see the link odiesoil.com/odies-finishes-application/

[@t-shirtguy7845]

I would like to use this for the charcuterie and cutting boards I sell. Can my customers just use my mineral/beeswax product over Odie's if it needs touching up over time?

[@Odiesoil]

Not really, to get same protection and durability they have to re apply with Odie's oil

[@chrisgalvan4757]

The table looks great. What was the final grit you sanded to? Thanks for sharing

[@bighim04]

I need the same information!

[@raylang2996]

@@bighim04 Mirka Mirlon 2500

[@todayfeelz5050]

It's a 400 grit.

[@apesonegotrips7]

Started woodworking less than two years ago. All I have to say is, where’ve you been all my life? Oldie’s checks off every box for what I’m looking for in a finish (seriously, I’m not being paid to say this). I needed a food safe finish that 1)doesn’t go rancid 2) I don’t have to worry about a person having allergies, and where food safe isn’t a necessity provides 3) protection against water 4) is UV resistant (so my projects done in cedar won’t fade). I thought I was going to have to figure out at least 3 primary finishes to always have in my arsenal in order to meet the necessary criteria for different projects. So, this will basically be the only finish I foresee using from now on, unless someone requests otherwise. One question, if this is the right venue: for things such as cooking spoons, how often does Odie’s need to be reapplies? Just wondering if I should continue sending a single use bit of oil to my customers with their purchase (this expense is out of my pocket because that’s how much I want my customers to have a good experience. Cuz that’s what it’s all about, sharing the beauty of our work).

[@Odiesoil]

Hello, your feedback made out our day. The regular works great on wood spoons, bowls, charcuterie ecc, in this case just apply 2 coats of the oil and let it fully cure for 2 weeks before you expose it to liquids (3 weeks for walnut), it has to be re applied only when is need it

[@Odiesoil]

Thank you for your trust in Odie’s products 🙏

[@adibella47]

If I finished top and bottom of a table with Cornwallis super duper everlasting + creative colors pigment 3 days ago and I plan to do a second coat of the original Odie’s oil tomorrow. Do I need to add a second coat to the bottom of the table or is it overkill?

[@Odiesoil]

Hi! Thanks for choosing Odie’s to finish your table! The underside of the table is typically fine with just the one coat but it wouldn’t hurt to apply another light coat to make sure it is all sealed up equally to the topside. It’s important to make sure both side are equally sealed to prevent any difference in moisture gain and loss. This will ensure wood movement will be kept to a minimum and help prevent any warping and cupping.

[@presbarkeep]

I applied a very thin coating to two pieces of camphor wood, one sanded to 400, the other to 800. After 2 hours, I buffed with a terry cloth, and no excess was coming off with a paper towel, however, there was no shine on either piece. So, I applied a bit more, and worked that in. Waited 2 hours, buffed again, and still no shine. I'm really putting in the elbow grease on the buffing, but neither piece has a luster. I was expecting the 800 grit to be satin, but both pieces are matte. What is the trick to getting a shine?

[@Odiesoil]

Please give us a call 850-695-2055, we will be happy to help

[@katydoran999]

@@Odiesoil why not tell everyone?

[@craftspirited]

@@Odiesoil yeah why not tell everyone 🙄

[@misstweetypie1]

@@katydoran999 maybe the person in charge of replying to KZbin comments doesn’t have the know-how to answer?

[@marchebert9813]

Maybe the conversation would be too long for the comment section.

[@fordguyfordguy]

would it also be correct to use this as a furniture polish or wax for stuff already finished?

[@Odiesoil]

yes, it will work great as long as the old finishing is not failing

[@paulramirez5668]

How often do you have to reapply the oil? Or is It a once and done finish?

[@Odiesoil]

Hello, you will have to re apply it only when is need it

[@ryandrzyzga]

Anyone use a 6 inch buffer with Odie's? I've been applying to Tigerwood with gray scotch by hand but it's taking more oil and way more elbow grease than in the videos. The Tigerwood seems way more porous than Walnut so it's not stretching as far.

[@Odiesoil]

Real Tiger wood is a fairly dense hardwood with a Janka Hardness of approximately 2170. You should be getting close to the same coverage as in the video, but slightly less, also your sanding level will have a factor in the coverage. You can apply the oil mechanically, just be sure not to use to much, and more importantly, be sure to buff off any and all excess oil until dry to touch.

[@brianwohn]

Can I use the white non-woven pads even if I only sand to 320 grit? Or do I "need" the coarser pads? Thanks for the video this is wonderful!

[@Odiesoil]

It’s typically recommended to use a pad rated just higher than your last sanding grit but a white pad will work

[@brianwohn]

@@Odiesoil Thank you!!

[@brianwohn]

@@Odiesoil sorry one more question. Do you wipe it down with mineral spirits or water after final sanding to make sure it looks ready to oil and to clean it before oiling?

[@TheBQ92]

Can Odie's Oil be used as a topcoat over wood that's had a coat of pure tung oil applied?

[@Odiesoil]

Yes, it is possible, follow same application process

[@elizaberg7581]

After buffing off (pine table top), it feels slightly waxy/sticky. Will this go away with time or do I need to buff more? Thanks!

[@Odiesoil]

hello, it means was not removed all the excess from the surface, we need some more info, please share with us your phone number

[@troybush5899]

QUESTIONS: 1. Can it sit for more than 1 hours? If yes, will it be more difficult to buff off? 2. Is it now waterproof? 3. Do I need to use coasters to prevent "rings" from sweaty cup or goblet? 4. How many square feet for walnut, maple, mahogany, etc. (woods with lower Janka rating)? ...Is there reference sheet?

[@Odiesoil]

1.yes, better to remove the product within one hour otherwise will be harder to remove and risk to leave product on the surface. 2. Yes, all our products will get you an waterproof finish after is fully cured (3/5 days). 3. no, is no need of coasters. 4. Depending on the wood type Odie’s Oil can cover up to 250 square feet on most domestic wood species, and aproximative 180 sf for american cherry! see link odiesoil.com/training-manual-2/

[@larryblair6914]

I'm refinishing maple stairs. I will likely sand to bare wood. If I stain the stairs, can Odies be applied over top?

[@Odiesoil]

Yes, is possible as long as the stain is fully dried, or you can use our system of stains. You mix one of our pigment powders direct into the oil, stir well, and apply as per the oil. See some videosodiesoil.com/mr-cornwalls-creative-colors/

[@lindaconway6146]

Can you put a polish on this afterwards for a little more shine and protection? Or is this needed? Thanks

[@Odiesoil]

Odie's is all that is needed. Your sanding level will dictate the "shine" and Odie's bonds with the wood and that provides the protection.

[@lindaconway6146]

@@Odiesoil thanks for the reply

[@CovChannel]

Applicator saturation is critical. Once that happens, it does go a long way. In other words....save your applicator.

[@skinnhellas271]

I got the universal oil but I didn't got the Odie's safer solvent and I live in Greece! . What's an alternative good way to remove any surface sanding dust before applying the Odie's Univesal oil?

[@Odiesoil]

Vacuum the dust, or brush it off using a dust brush. Then, wipe the surface using a clean cloth.

[@Boom-oq5yj]

Is the 2500 grit pad essential? These are hard to find. Also you were clear about not putting too much but then didn't measure it out when you spread. Were you eyeballing the amount you applied in this example?

[@Odiesoil]

We do recommend using a non-woven pad rated equal to or just higher than your last sanding grit. They are always available on our website! If you are new to Odie's then measuring it out by volume is a great way to get used to being accustomed to how much you need. Once you are more familiar, then eyeballing will be perfectly fine.

[@elizabethkavouris7446]

Would applying more coats of oil improve the durability of the finish? If so, how soon after the first coat can you apply the finish 2nd or 3rd? Thanks!

[@Odiesoil]

Basically, more layers more protection. Wait one day in between coats.

[@elizabethkavouris7446]

Thank you! When applying subsequent coats, do I need to prepare the surface or just go ahead apply the oil?

[@elikoffler4323]

How long do you wait to apply second coat after using super duper oil

[@Odiesoil]

Hello, it is one day in between coats

[@dbcooper6020]

So what do I do if I want a higher shine? Put a second coat down or use a different product?

[@Odiesoil]

The sheen is primarily dictated by the surface preparation (sanding in most cases) the higher you sand, the higher the sheen. This takes place before the finish is applied. Once the finish is applied, you can micro-build upon the finish with additional coats to increase the sheen, depth, and luster. you can also increase the sheen by burnishing the surface with a higher (than your last sanding) grit non-woven pad or even sand between coats, you would also use this higher-rated pad to apply the finish.

[@danielleweston1492]

Can you share a link to the pad used to rub the product into the wood?

[@Odiesoil]

Please see odiesoil.com/non-woven-hand-pads-6x9-singles/

[@seanditch4419]

Hi thx for the video, may i ask if theres an equivalent to the Mirka Mirlon 2500 pads? Here in Britain it would appear to be a rare product, and therefore they charge you millions £££ for a ton of pads in bulk. thx

[@Odiesoil]

Hello, for this specifically question we do recommend to contact our distributor in UK, if I am not wrong he might stock the pads www.odiesoil.com/europe-and-africa-dealers/

[@seanditch4419]

@@Odiesoil ah brilliant thank you

[@TWC6724]

Another question, can I apply it to a freshly hand planed surface or do you have to sand first?

[@Odiesoil]

Yes, You can apply to a hand planed surface. In fact its my preference.

[@patrickweaver5290]

When u say you prefer it would u plane the wood apply odies and then sand to desired grit or apply after finished sanding?

[@Borescoped]

@@Odiesoil I’d like to see a video of James or Matt applying the various products to a hand planed finish. Is that something y’all can do?

[@Odiesoil]

@@Borescoped did you check our instagram account?! plenty of new videos

[@dalevandenbussche5004]

I’m getting ready to do a project with 100 year old barn wood fairly rough surface how would I apply to that?

[@Odiesoil]

Hello. We do recommend super duper oil light, please see instructions on the application, for more info please call us 850-695-2055 Est time www.odiesoil.com/odies-finishes-application/

[@Jennegga785]

Can I use ODIEs oil on tha handle of my wooden knifes ? Where can I buy it ? Jakobsen from Norway !

[@Odiesoil]

Hello. Odie’s oil universal will work great for your project. Please contact our distributor in Norway, Eric will be able to offer all the support need it [e-mail]

[@mariamidura3089]

How do you apply it to intricate carvings? Thanks.

[@Odiesoil]

We do recommend super duper oil applied sparingly by brush, make sure though that you wipe off completely with a 100% cotton terry towel until dry to the touch!

[@genepearson6163]

Can you use Odie's oil as a finish for smaller projects like jewelry boxes?

[@Odiesoil]

Hello, thank you for your question Odie’s oil works excellent on any type of project big or small and on all wood species (indoor or outdoor), there are no limitations on sanding, higher you sand higher the sheen. Just make sure you follow the application process step by step and cure times and everything will work great

[@dafickler]

Did you try it yet on the smaller boxes? Thoughts?

[@donproctor3445]

Do the terry cloth towels become single-use?

[@Odiesoil]

yes, they can't be washed

[@doncorne8707]

I'm applying this to an old table that has a finish on it. Any special instructions to applying to something with a polyurethane finish?

[@Odiesoil]

Hello. Thank you for choosing Odie's oil! No, is same application! apply sparingly with a pad, and remove after 40 minutes with a cotton terry towel (old bath towel).

[@joelrightler]

Could I lightly heat up the oil to make it more viscous? Would it spread easier?

[@Odiesoil]

We don't recommend to heat the oil, however make sure you stir well the oil in the jar and use a micro-fine pad for application, see our website odiesoil.com/non-woven-hand-pads-6x9-singles/

[@davidlash4125]

How long do I wait until I can add a second coat, if I want?

[@Odiesoil]

Wait at least one day in between coats.

[@RobSandstromDesigns]

What do you do if you do apply too much? Do you just keep buffing?

[@Odiesoil]

Yes, keep removing and buffing off any and all excess, residual oil until dry to touch.

[@joetucker3436]

Could you make a video using oil on complete unfinished piece. Theres already a finish on there before you applied odies oil.

[@Odiesoil]

Hello, please scroll down the page for more videos www.odiesoil.com/faq/

[@miketinghitella7902]

No Joe, that's the sanding level, not any prefinish. One of the many great things about Odie's Oil is that you can sand to any grit. You can't do that with the other hardwax oil finishes.

[@fmfnateman]

I got walnut sanded to 5,000 grit and looks like it has epoxy on it already and it has nothing.

[@henrycollins2478]

How well will it hold up on a conference room table?

[@Odiesoil]

Hello.Odie’s will hold up excellent for a conference room. It’s formulated for hardwood floors, countertops, table tops and bar tops. Odie’s will outperform any finish when applied and cured properly. We do recommend 2 coats of Odie’s oil and one of the butter or wax (wait one day in between coats).

[@stephenpeterson4738]

How would this do on spalted maple?

[@Odiesoil]

Will work great, just follow the application process step by step www.odiesoil.com/applying-odies/

[@michaelholland9534]

what grit would you take red cedar to and what coresponding pad colour?

[@Odiesoil]

You can sand to any grit! There are no sanding restrictions with Odie’s. It really all depends on the look and feel you want. The higher you sand the more refined the surface and it will be the basic dictation of sheen, the higher you sand, the higher the sheen. When choosing a pad, you typically want to choose one rated just higher than your last sanding grit.

[@markmoulin41]

Was this application done on raw sanded wood, or did this cherry slab already have a coating on it?

[@Odiesoil]

Yes, it was sanded! our finish works too over other finishes, however for best results is ideally to apply on bare wood. With our finishes higher you sand higher the sheen!

[@jimbillias7962]

Hi all, just got a question,l done my slab with an oil that is not shiny at a all, can l on top with a different gloss oil??

[@Odiesoil]

Was the slab finished with Odie’s Oil or a different finish? With Odie’s finishes, the sheen is primarily dictated by the surface preparation (sanding in most cases) the higher you sand, the higher the sheen. You can also build upon the sheen with additional coats and by using the various finishes in our line up.

[@dandan1364]

How do I find the right pad for my sanding grit?

[@Odiesoil]

We sell them on our website under the applicators section. We typically recommend to choose a pad rated equal to or just higher than your last sanding grit. We currently carry 4 pads. Maroon very fine-rated 240-360 Grey ultra fine-rated 400-600 Grey micro fine-rated 800-1000 White-non abrasive

[@jaredlewis2961]

Is it safe to wash the terry towels in the washing machine used for buffing?

[@Odiesoil]

Unfortunately they have to be disposed, they can’t be washed

[@kofteci408]

@@Odiesoil Why not? Since it's food safe there should be no problem with contamination. Would it damage the washing machine?

[@matthewharry2803]

Oily rag rule

[@matthewharry2803]

I assume the oil would polymerize harden) on the towel and make it unusable

[@TzufFamilyBand]

Hi. What grit do you sand the wood to before applying the odies oil?

[@Odiesoil]

With our finishes there are no sanding restrictions or limitations! The sheen is primarily dictated by the sanding. The higher you sand, the higher the sheen. 180-320 for matte to low satin sheen, 400-600 for satin to medium/ medium high sheen 800+ for high sheen. You can also build upon sheen, depth and lustre with additional coats.

[@TzufFamilyBand]

Hi. I have some questions I was hoping you could help with 1)What is the minimum dry time for a table? We want to renew our dining room table, but don’t have a week to wait for it to dry. What would you say is the minimum time to wait for use, and perhaps the precautions to keep in mind while using until it’s fully cured? 2) can you help me calculate how much odies oil I need for a table that is 1.4meters x 1.4 meters. 3) is it best to put two coats for a table? If so, how much do you reccomend in between coats? 4) I have a finishing wax called deylina wax. How much time do you reccomend waiting in before waxing? Thank you 😊

[@Odiesoil]

@@TzufFamilyBand we typically recommend 3-5 days cure time before being subjected to standing liquids. The table can be ready for light duty use the next day otherwise but it’s best to tread lightly. These minimum recommendations would apply to any finish. Once the applicator pad is saturated with Odie’s Oil you’ll get approximately 22+ Sq ft of coverage per ounce of oil on hardwoods like oak, cherry, walnut, maple…. One properly applied coat of Odie’s Oil is all that’s needed for protection and durability. The only thing better then one coat of Odie’s is two coats! With additional coats you will micro build upon the finish adding a little more sheen, depth, lustre and that silky smooth feel. We do not recommend using any other non Odie’s brand of finish or wax over Odie’s as we cannot guarantee a proper bond or performance. If looking to add a wax coat, we recommend Odie’s wax. We would recommend waiting 3-5 days before applying the wax.

[@neilpaterson3086]

Hi, If I use a white non woven pad to apply Odies oil can you tell me what grit of paper should I sand the timber to. Thanks

[@Odiesoil]

Our white non woven pads are non abrasive so they are typically used on surfaces sanded to 800 and above. The non abrasive pad won’t abrade or mar the surface. We typically recommend choosing a pad rated just higher then your last sanding grit as the slight abrasiveness does have its benefits. Our pads are as follows. Maroon pad-rated 240-360, Ultra fine grey pad-rated 400-600, Micro fine grey pad-rated 800-1000, white pad-rated non abrasive.

[@neilpaterson3086]

@@Odiesoil Thanks

[@randolph9938]

Can i use it to acoustic guitar?

[@Odiesoil]

Yes, Odie’s works great on guitars, for more information we recommend contacting our distributor that’s is an guitar builder and is using only Odie’s oil for years, if you have an Instagram account this ia his account info @jwaguitars

[@grega2691]

On wood floors, does Odie's Oil provide any scratch resistance?

[@Odiesoil]

Yes. Odie’s does provide scratch resistance by molecular bonding in the wood and therefore densifying.

[@grega2691]

@@Odiesoil Is this finish as hard as a polyurethane? How well will this product wear with a home with dogs?

[@Odiesoil]

Joyce Thomma please watch our videos to learn more about how Odie’s works. Odie’s oil finishes are totally different from polyurethane, our oils molecularly bond with the wood and will offer depth, stability, and protection to the wood. Odie’s will outperform any polyurethane on the market, as per dogs- it’s inevitable that polyurethane will scratch and poly is virtually impossible to repair. as per using Odie’s... Odie’s will harden in the surface and reduce scratching, but when scratched repairs are simple....you will be able to spot repair

[@gvalverde007]

Good afternoon I can apply the product on the resin in a river table and in tables for chopping vegetables

[@Odiesoil]

Yes 😀

[@collindavis2656]

I heard that you should let your piece sit for 2-3 weeks before use. Is this true?

[@Odiesoil]

No, you can use you project next day, however you have to allow 3 to 5 day to fully cure before you expose it to liquids

[@ta3355]

What about adding a ceramic coating?

[@Odiesoil]

We do not advocate the use of any ceramic coating as they contain harmful and dangerous substances. Beyond that, we do not recommend the use of any other finish to be applied over an Odie’s finish as we cannot guarantee a proper bond. A properly applied Odie’s finish will withstand much abuse and is very easily maintained if and when needed. We would recommend to read our blog posts on our website for more information.

[@imstilbettyboop1]

Can you use this on painted surfaces?

[@Odiesoil]

Yes you can. don't forget to use a very small amount and remember to buff it all off.

[@KGM-ty2nt]

How often can you reapply Odie's?

[@Odiesoil]

You have to re apply only when is need it, could be after one year or after many years, all according on exposure

[@ronaldtreitner1460]

a good reason not to use this product is just watching this video. typically, many thinking of using such a product are doing so on unfinished wood, so what does he do here, uses an already polished piece to make it look better than it is. if its so great why the con job, anything will look great if the surface its being used on is already polished........ P.S., i also love how in the comments he tells people to contact him for a quick sell rather than answering the question so everyone interested can learn the answer, so much for keeping all those new customers with questions happy.

[@michaelmcevoy9278]

He says below that it is unfinished wood.

[@jeepersmurphy2570]

He says it's unfinished and usually with these kind of oil/hardwax finishes benefit greatly the higher you sand to. Looks like at least 320 grit. I can understand your skepticism, but Odies is a great product.

[@NellyEIEI]

You're 100% wrong. I use Odie's oil religiously when finishing my wood and epoxy projects. It was already sanded prior to the application. Not finished. BIG difference

[@meuhey]

@@NellyEIEI is this product good on 180 grit

[@dj7dust76]

how do you do the edges

[@Odiesoil]

We do recommend the super duper light oil, it is a thinner formulation therefore will be easier to apply

[@ohkwoodworking9705]

Can it be applies over a polyurethane finish?

[@Odiesoil]

Yes, it can. Odie’s will cross link and molecularly bond to a great variety of mediums including other finishes. The downfall to using Odie’s over other finishes, even though Odie’s can help repair and rejuvenate them, is that those existing finishes are the barriers between the true cross link and molecular bond with Odie’s and the medium itself and that existing finish will be the weak link.

[@sarahsanchez7171]

Will it hold up to the abuse a butcher block countertop will endure Ex water, grease

[@Odiesoil]

yes, will do work great as long as the finish is applied correct and removed completely and make sure you let it fully cure for 2 weeks to become waterproof and heat resistant

[@KokoNaki]

@@Odiesoilwhat do i use to clean a countertop sealed with Odies Oil

[@Odiesoil]

There are three different ways to clean things that are finished with Odie’s products: You can mix 1 part vinegar with 10 parts water and clean with a terry cotton cloth You can use soapy water (like Dawn dish soap), but remember to rinse all the suds off, and then wipe it dry Or you can make your own cleaner using Odie’s cleaning concentrate. To do this you can make a mixture, mix 2% of Odie's Cleaner Concentrate with 98% water in a spray bottle. Just spray and wipe. This will clean, refresh your finish. Start using this mixture after is fully cured. Start cleaning your cabinets after are fully cured for 2 weeks

[@rogeliorojochavez7558]

Are this waterprooft ? And how often do you have to apply it?

[@Odiesoil]

Yes, all our finishes are waterproof if applied correct and allowed to fully cure up to 3/5 days. Is no need to apply every month, just when is needed all according on exposure could be after many years, or every year.

[@rogeliorojochavez7558]

Thanks for the answer ,,

[@MrBdwain]

Can a water-based polyurethane be applied over Oldie's oil?

[@Odiesoil]

No, is not possible and there is no need to do this, please give us a call and we will be happy to help 850-695-2055

[@mat..n.7061]

This table was already finished. What about applying it on unfinished wood?!

[@Odiesoil]

Check our channel there are dozens of videos made by Odie's Team or our customers! see also link kzbin.info/www/bejne/d56koHlmnLGqoc0

[@ms.ms.9427]

I just purchased a jar of Odie's oil to use on a butcher block countertop for our island. Should I use the wax as well? If so, how long should I wait after I'm done with the oil (days?)

[@Odiesoil]

Hello. Yes, will work good, basically you will create layers of protection, wait one day in between coats

[@s.h.7893]

what happens if wine is poured. Thanks

[@Odiesoil]

As long as the finish is applied correctly, and allowed to be fully cured you should get a water-repellant finish and stain resistant.

[@rdsattube]

Noticed that this slab is showing a sheen from the start of the video. How is that possible?

[@Odiesoil]

The sheen is primarily dictated by the surface prep. The higher you sand the higher the sheen. However, you can step the sheen up once you’ve already finished your work. see also video kzbin.info/www/bejne/mqDGmWeJbNWGl6c

[@theoctopus_9056]

Sir i need your help am from India Kerala

[@Odiesoil]

Please send us an email at [e-mail]

[@kng9186]

I bought Odie about 1 year about, is it still good to use ?

[@Odiesoil]

yes, is still good to go.

[@kng9186]

@@Odiesoil Thanks.. But I cannot open the lid. Any trick to open it ?

[@Pressingontoperfection]

Where is it sold.

[@Odiesoil]

www.odiesoil.com

[@Timberwerks]

Can I apply with 0000 steel wool?

[@Odiesoil]

Yes, you can

[@larryblair6914]

@@Odiesoil good to know. i hace lots of 0000 SW

[@guybaumgart1549]

Dommage que ce n'est pas traduit en Français, je n'ai rien pigé.

[@dianebrooks6261]

What if the wood has a finish

[@Odiesoil]

It would be best to strip or sand it off and start from the bare wood. An existing finish will be the barrier between Odie’s and the bare wood and if the existing finish is prone to failure, there’s only so much Odie’s can do. It will however help restore and refresh it much more easily than most of all other finishes if a complete strip refinish simply is not worth the effort.