Old crow is off the table (rat rod part eight)

[@garyparker2969]

PLLEEAASSE DO NOT CHOP IT 😣😣😣😣 !!! LOOKING SOOO COOOLLL,,,, thanks for Sharing n God Bless All.

[@HardCoreFab]

I don't think the lights on top would look good with a chop and I don't want to lose them so I don't think it will happen

[@garyparker2969]

😥😥😥😥WWWWHHHEEEEUUU !!!! LOL.

[@AndysDogHouse]

It's nice to see the Old Crow off the table. It gets the old Rat Rod juices flowing. Man you could even wear your hillbilly hat when driving. You have lots of room. Keep it going and thanks for sharing.👍👍🍁

[@speedbuggy16v]

Awesome, looking better every day.

[@johnnyberlinn1663]

Please watch the volume for you guys and gals with earphones thanks

[@geneyusko5975]

That lift is great a friend of mine built me one it saves my knees .

[@rodneyclements6190]

On the valve covers...cut some Old Crow logos on the plasma table to fit the blank flat area on the covers. Just a thought. Looking great so far!

[@HardCoreFab]

That's a great idea!

[@garyharris1350]

It look like a eagle sick truck

[@petejoy6328]

Like the part about fat old guy! Smarter not harder!! Like your work brother! I’ll be watching for sure!!

[@mountainsgarage]

Love the channel, you build some cool stuff! For the tube chassis cars I have built the engine is 1-3 degrees up, but they are static at 3” off the ground. I guess with air ride the engine pointed down makes sense. I am not questioning it just thinking out loud! I have replaced too many broken transmission cases to not run a poly transmission mount with solid engine mounts though, that thin aluminum isn’t as strong as the block and gets rotational force and chassis flex. Looking forward to the next one!

[@henrygibson1530]

It's coming together nicely! 😁

[@HardCoreFab]

Thanks! 😁

[@henrygibson1530]

You're welcome!😁

[@TrendsbySterling]

Trans mount is nice, however you didn't trim the top of the mount to match the motor mounts.

[@shanewright6958]

Great job. It's looking good 👍👍🇨🇱

[@HardCoreFab]

Thanks 👍

[@jdbwz5307]

You make it look so easy.

[@caryford560]

That looks really cool.

[@streetkd08]

Looking awesome man

[@HardCoreFab]

Thank you!

[@spiderbrandt4066]

Love your channel , At the start you where a long way from the mic and it was hard to hear you, wow Is the rear Tyre big enough , this should be one cool car when you finish it .

[@staytunedrodcustom5855]

Coming along good man!

[@jlennox54]

New cross member looks 1/2” lower on driver side.

[@HardCoreFab]

Yeah the camera angle makes it look jacked up. Trans also looks like it's at an angle too but I assure you everything is level

[@a3van609]

11:14 You should have cut the video there. Anyways great work and keep it up.

[@charlesthomas6210]

Love the look. But would like to see more fabrication and work in the video. Just saying

[@HardCoreFab]

I would too! I'm giving it every extra ounce I got but I do have to balance it with the rest of my responsibilities.

[@fullblast9928]

Where's the rubber trans mount?

[@HardCoreFab]

Solid motor and trans mounts my friend

[@shanethompson7543]

Bad$$

[@timwegman5776]

Just don't do a huge chop only a couple inches

[@HardCoreFab]

no chop

[@georgemcmillan9172]

Bro, you could use a better microphone.

[@wjmoon2831]

I don't think it's his mic...when editing your video you should be able to go into the settings and set your audio channel to stereo (it's probably set for mono)...my mic does the same thing since I record on my phone, and I always have to go into my audio settings while editing (I use DaVinci Resolve to edit) and change from mono.

[@wjmoon2831]

I should have mentioned I use a Rode mic with my iPhone to record..if I use the phone's built-in mic I don't have that problem

[@HardCoreFab]

@@wjmoon2831 Thanks for the tip! You are right I will check those settings form now on!

[@dougwiest9318]

@@wjmoon2831 ALL I AM GETTING IS ONE LOUD CHANNEL AND ONE CHANNEL OF VOICE THAT'S PRETTY MUCH INAUDIBLE.