Please subscribe if you enjoyed this video. Thank you for watching.
Пікірлер: 31
@josemoreno33349 ай бұрын
I fixed mine almost the same way. It worked well. Thanks for the tip. Saved me some bucks. Hello from Buckeye, Arizona.
@OldGuyDIY9 ай бұрын
You are welcome.
@pibblesnbits5 ай бұрын
I just bought a tube of RTV silicone and just siliconed the piece back. Took two minutes to do, and 24 hrs to fully cure. Once cured it is good as new. You dont even need to take the door apart to apply the silicone but I highly recommend using painters tape to keep the stuff from getting on the car interior as it is difficult to clean but can be cleaned while wet with rubbing alcohol.
@OldGuyDIY5 ай бұрын
Thanks for the tip.
@RJ-ex9on5 ай бұрын
You are the true MacGyver!!!! Thanks a million!!!!
@OldGuyDIY5 ай бұрын
You are welcome.
@koelg5858Ай бұрын
Thank you ❤
@gatorb8 Жыл бұрын
Thank you.
@mayken6661 Жыл бұрын
Thank you. Every other videos malfunctioning window switch, not this issue
@OldGuyDIY Жыл бұрын
You are welcome.
@user-jh8jh9up3v6 ай бұрын
Thank you for the help !
@OldGuyDIY6 ай бұрын
You are welcome.
@USDevil17753 ай бұрын
Great video! Keep posting!
@OldGuyDIY3 ай бұрын
Thank you.
@swampman56 Жыл бұрын
Nice job
@OldGuyDIY Жыл бұрын
Thank you.
@52tippy Жыл бұрын
Nice, I'll be working on mine soon.
@2Jeezuzisreal6 ай бұрын
Thanks. Is there a way that I can wire up my windows to work with the key off. It's ridiculous that my kids can't even get fresh air and the rear door glass lift has no key lock where does the passenger door.
@OldGuyDIY6 ай бұрын
If you want to modify the existing wire harness, you can attach the power wire for the windows to a red that is always hot, under the dash.
@A1Santoss973 ай бұрын
I used Superglue and Zip tie the whole thing to hold over night and damn it’s holding up
@OldGuyDIY3 ай бұрын
Nice job
@mayken6661 Жыл бұрын
Have you happened to do the loose windows issues these vehicles get over time? 👍 subscribed
@OldGuyDIY Жыл бұрын
No, I've never encountered a loose window in 20 years of driving this generation vehicle, Tahoes and Suburbans. If I had a loose window, I would remove the inside door panel with the window in the full up position and use a 10mm socket to tighten the 2 friction fittings with the rubber liners that secure the window glass to the actuator assembly. You will see the bolts that need to be tightened about 6" below the window opening in the car door and about 6" in from each end.
@user-vu7sc9uq2x11 ай бұрын
What was the broken part called when you looked it up on eBay for $80 ?
@1LElife8 ай бұрын
probable the entire door panel
@kingant892710 ай бұрын
Were the buttons not working in the 1st place ??
@OldGuyDIY10 ай бұрын
The buttons work fine. The beige panel that the switch sits in was not properly attached to the interior door pane.