OM606 Hunting Fix

Here is quick and easy way to fix a hunting injector pump, please remeber pump hunting could also be caused by mechanical wear or further issues so always seek expert advice if problems persist.
To view more great products please visit our shop following the link below.....
www.dieselpumpuk.com/shop/?or...

[@Robin96]

I have a S124 Mercedes with OM602 without turbo. When i bought it, it was very sluggish about 19-20 seconds from 0-100 km/h. Then i decided to turn up the pump. The first thing i did was turning the ADA screw all the way up. Then i lowered the idle speed with those two screws in that round hole as much as i could and turned the fuel up 2 turns with the low-left screw under the lower lid. Then it started to return to idle quite slow and then i turned the screw that's one upper to the fuel screw almost half a turn counter-clockwise. Then it started to work great and it feels like the car has about 20+ horsepower. Later on i advanced the timing on the injection pump by turning it towards the engine block almost 1 cm. After that the engine has a bit sharper "diesel sound". That gained also a little bit power output and fuel consumption turned down a bit. Now the 0-100 time is 15 seconds. Sorry my english is not the best, i live in Finland!

[@armoi539]

602 sai vetoja

[@chrisfleming5109]

Good to see you boys are not letting the virus slow you down. The roads are very quiet so great chance to give the cars some welly.

[@rossconverse7038]

Thanks for sharing your expertise. Ross Maine, USA

[@glonel3294]

I am Spanish, I speak very little English but your videos are great, I appreciate the interest you put in it, thank you very much, greetings from Spain, my dream has always been to modify a patrol, and you do incredible work

[@tab6522]

Love the channel man, just picked up an old diesel and really need tips like this!

[@chrisrundlett3707]

Great video! Looking forward to installing OM 606 in my Defender! Checking out what you have on the lift there behind you - not Puma...

[@mostafahasan6522]

Thank you for the valuable information, my friend. Can you please give us a video on how to disassemble the diesel pump?

[@ta51503828]

Thank you for the video great work. How is this done on om617 m-pump? Is the adjustment in the same location? Will turning clockwise make part throttle performance more jerky or smoother/less jerky? Thank you.

[@BunkocziR]

That throttle response is out of this world

[@28imike]

I'll have to try that on mine. Mine has a slower lope though as you can hear on my first start up video.

[@sleepermondeobuild9834]

thank you bro i have this prob in my 123 and i will do it now.

[@carlbickle9467]

Do you calibrate your upgraded pumps in house?

[@j-bolo6637]

Very random one ans I'm not sure if youd know... but I've got a bmw m51 2.5tds as a project, and I'm getting the same issue! Apparently they are mechanical pumps also. Would you take a guess in saying I could use the same thinking as this to sort my issue? Various people have said it's the pump but no really knows👎 good old bmws🙄

[@MrAradulescu]

Cool will that work on a 250td c class with the pump that’s on it??

[@whatyoumean3383]

Thank you

[@marcink-bus2291]

It happends in my 124 603 turbo only in summer... in winter engine run smooth

[@user-bh1uc6yv5t]

What is this modification of the motor? and what kind of fuel pump?

[@nickjordan5286]

Thanks for the video. Can I do this on my 98 E300 turbo diesel with an OM606 ? I'm not the most mechanically minded person and am having difficulty identifying where to do this on my car. Your engine layout looks very different to mine. Thank you.

[@no-damn-alias]

You have an electronic pump. Can't adjust it

[@________4843]

Is this bad for the engine, I like the sound of it for my build but don't want it to damage my engine, if I back the nut off to achieve the sound would it hurt my engine?

[@GCRTeamPortugal]

I have the same issues but i have stock pump edc om605 Is the same? Thank you

[@ferguson20diesel49]

What do you do about engine that idles perfectly fine for 5/6 seconds then hunts up and down for 2/3 then rinse repeat for ever

[@oilcan2787]

What are you putting in the Mustang?

[@Hal-cv8cf]

Again, great video, you guys should considered about buying a new microphone

[@heavy_low_n_slow]

Can this happen to an EDC pump? My stock n/a 606 hunts on start up

[@keuninkske]

Will try this one on my NA om602, i was searching for this problem and was already thinking about getting the pump to the bosh center to test it

[@crespoandrade]

Did it fix your problem in the end?

[@keuninkske]

Nope, doesn't help, I will check and clean the hydraulic valve lifters next , I could use better explanation for the complete governor housing and its components, I adjusted the full track travel screw and brought back the idle with the idle stop screw, but I seem not to be able to make black smoke, torque screw and 2m spring adjustment doesn't help me either, I can see that the rack should be able to move further than she does now..., can somebody make a video of the regulator internals, and how they can be adjusted, nothing on KZbin or internet helps me fully out

[@crespoandrade]

@@keuninkske did you check if all your vacuum lines are tip top? Check all those freaking rubber connectors between the pipe lines I had a rotten one soon I've replaced it it changed the idle completely There's also on the top of the fuel pump what it looks like an Alda as they call it it think these are has a nut and a screw inside the housing you can adjust it and it lower or increase idle from there. Also inside it there's a diafragm made out of rubber when it goes to waste it also causes problems with the pump I've changed mine 2x already. Hope it helps mate good luck with your quest

[@kubaSWAT]

Ive got om606 TD but i have different pump, dont have acces to this screew

[@georgbennings8540]

WMO DIESEL IN OM617 IST OK ?

[@atos.nympha3451]

Looks like u building incubators with om 606 for convid19

[@johnmunro8707]

Any pump mods that can be done to a 2.5d 5cyl ? Cos I need more power 😂

[@brankicacermelj6270]

How you do that on electronic fuel pump?

[@dayuntoday]

Can I do it on my w201 on om601 engine in cold start always do it shake but im check every other possible reason?

[@DieselPumpUK]

Sanid Džanan yes give it a try.

[@tomschneider8926]

TOP!!!

[@ben_adam8277]

Hi thanks next time can you focus the cam in the work

[@amarrouge7696]

I suffer from the same problem in the engine of the OM605 662 fuel pump. Can you help me

[@jumpspace7414]

Just do what he does. Save yourself a lot of money.

[@conradsinsua7415]

More pls...how come that engine response is so quick?

[@JoeHeine]

Conrad Sinsua just guessing on this one, but maybe because he has the intake manifold off?

[@Diesel8290]

its because its a modified pump with larger element.

[@doktorjonsson3860]

But what if I have no hunting, but want it? I'd like it to hunt, but a bit slower like once a second or something like that. Is there any way to make it hunt on idle but drive as usual when using throttle?

[@DieselPumpUK]

Doktor Jönsson this engine had no hunting, I backed off the nut for the video so you could do the same.

[@doktorjonsson3860]

@@DieselPumpUK But I want the "frequency" to be slower, in the video it changes rpm multiple times per second and I'd like it to be like once a second. Is there any way to achieve that?

[@Diesel8290]

@@doktorjonsson3860 the car will most likely drive like shit on part throttle.

[@dennislima3075]

If you want it to lope like a bro truck, you could either do what's shown in the video, or go with oversized injector lines, the lope comes from the velocity of the fuel being too low (atleast that's how it works with bigger lines). Either way you do it, it will screw part throttle driving up, but it'll sound cool I guess haha. Also if your ELR is operable, you can turn the idle down with that, to get a slower chop.

[@-smp-scientificmethodpersp838]

You're a freaking hero. No joke P.s. what about an electric fuel pump?

[@dennislima3075]

My lift pump was having a bit of trouble, threw a $50 Holley inline pump in as a temporary fix to get me to work. Works like a charm. Be sure to get a low pressure self priming pump. I believe mine is a 4-7 psi pump, itll shutoff if pressure exceeds 7 psi. I've got it inline just before the primary fuel filter as it has it's own (larger micron than our primary) filter. That's what you want just incase. 5 minute install.

[@-smp-scientificmethodpersp838]

@@dennislima3075 okay, I'm gonna do this. I'll get back to you after I do. Might be a few weeks. Thank u

[@dennislima3075]

@@-smp-scientificmethodpersp838 it's not the cleanest install. But it works, and it works without messing with any original parts, just add it in.

[@gunayturgay4977]

The 1988 model 300.Td om603 automatic transmission lifts up to how many hp. thank

[@DieselPumpUK]

Gunay Turgay email the shop please

[@gunayturgay4977]

@@DieselPumpUK [e-mail]

[@gunayturgay4977]

[e-mail]

[@adhanonoi]

The disel power..

[@auto-servisd2422]

Hello I'm from montenegro i have mercedes w210 e250Diesel 113hp Can i make it faster with pump i dont have turbo can i make it faster thanks

[@DieselPumpUK]

Tsi Gaming a turbo install would be a must for extra performance

[@auto-servisd2422]

@@DieselPumpUK can i crash dhe engine after install turbo ?

[@auto-servisd2422]

@@DieselPumpUK can i install turbo from om606 or om605TD

[@emilandrei9328]

With this trick om606 pump run without ecu remap?

[@danielmorrissey5842]

And adptor kit for 0m606 to 95 hilux 5 speed manual trans

[@DieselPumpUK]

daniel morrissey we are producing one soon

[@mmdohderdera9602]

This is what happened to me when I installed the parts that I bought from you

[@DieselPumpUK]

mmdoh derdera, well now you or your pump builder knows how to fix it.

[@mmdohderdera9602]

@@DieselPumpUK I installed the parts myself and they were set up on the test machine. Upon starting the engine, it happened as I indicated

[@adrianstefaniak3823]

Kle kle kle kle kle kle kle