Hi, really good build, I am doing the same with an OM606 and have a dieselpump UK injector pump. I am struggling to find a suitable water pump, I see you have a jabsco type pump, I don't suppose you have the model number for it? did it come with a serpentine pulley or did you make that up yourself?
@STRACHU100 Жыл бұрын
Hi Seanf42, Jabsco pump purchased from supplier who sales marinisation kits for mercedes engines (can send you details on pv) pulley i bought original mercedes part for the steering pump- fits perfectly.
@benhawke72312 жыл бұрын
Thanks for the detailed info 👍🍻🥃🇺🇸😝
@guinsou20002 жыл бұрын
Very nice project indeed! I've done om602 turbo boat with a lot of work too.including watercut adaptation plate going from om602 to Mercruiser, raw water oil cooler, silent bloc mounted on 2 stainless steal plates allowing me to set the height of the engine right in front of the drive shaft and so on and so on. In my case I had no need to change IP. but i think your om603 have smaller elements inside resulting on slight but noticeable loss of power compared to the standard 177hp of the om606 turbo. dudes from finland and englands can fix that for a certain amount of money if you consider the power is worth the money. Wish you happy diesel boating!
@STRACHU1002 жыл бұрын
yeah, i know, the sections are 6.5 instead of 7,5 or something. I check how it performs with this setting and then I can always upgrade th IP or turbo. I still have the o;d pump with the sections
@guinsou20002 жыл бұрын
@@STRACHU100 yep i did the same on mine. actualy i do 27 knots (50kph) with the original settings on my skanes 575. I think i will add a inter cooler this year or the the next and it will be fine for me. maybe super power on my next project with an om606 this time. by the way did you cast yourself the bell Housing or did you bought it somewhere? it looks pretty and strong!
@STRACHU1002 жыл бұрын
@@guinsou2000 nooo, i bought it! quite expensive too. I thought of casting it myself afterwards, maybe on another project
@0sci2 жыл бұрын
@@STRACHU100 Nice build! Where dig you buy it from?
@STRACHU1002 жыл бұрын
@@0sci do you mean the boat or the engine? all information you can find in my movies, cheers
@matui6983 Жыл бұрын
Hope you have provision in that stainless steel heat exchanger for at least one zinc anode preferably 2 of them, normally one st each end of the tube stack. Even if 316 stainless has been used to make it saltwater will eventually pit and eat it away. The sacrificial anodes will help extend the life of h/exchanger.
@STRACHU100 Жыл бұрын
Thanks for your comment, I have been thinking about it, it can be done relatively easy. Should the exchanger rot away though its relatively easy to replace and not too expensive.
@okkymahardika748 Жыл бұрын
Where I can get such clean om606
@STRACHU100 Жыл бұрын
Did you watch the movie? cleaning is the best part of it. So, in simple words- you can't :)
@marklchapman278511 ай бұрын
I have an 0M636 in my sailboat at Hamble point Marina I can’t find anybody to work on it …
@STRACHU10011 ай бұрын
Hi, I could probably help you but I moved back to Poland some 5 years ago.... I used to live in Hamle (Astral Grdens) lovely place
@bukyekaiko32332 жыл бұрын
Hello there... What pump are you using to circulate the sea water through the heat exchanger? I do not quite get that setup. I do direct keel cooling though but this pump looks cool and if it's an adapted item I'll like to grab it for a try. I've used OM366 LA and the OM441 LA. I want to try out the MAN 2865 Series. I'm out here in Nigeria.
@STRACHU1002 жыл бұрын
Hi. It is a Jabsco pump (very popular for such set up) . Cheers from Poland
@bukyekaiko32332 жыл бұрын
@@STRACHU100 Thank you. I'll look it up to see if there's a similar Item here in Nigeria. What was your prop Diameter? Thank you again.
@makingcookingfixing2 жыл бұрын
Thank you very much for your clear explanations in your video. I am planning to find a OM606 engine as well. What injection pump did you put in? And did you make adjustments to it? Thanks
@STRACHU1002 жыл бұрын
I managed to buy a pump from W140, 3,5 TD, which is supposed to give me more power and is fitted with ALDA- a pressure-vacum actuator to connect with turbo. I didn't do any adjustments myself however I had the pump proffesionally bench-tested prior installation. It is strongly recommended to do so to make sure its condition.
@mushtaqali2742 жыл бұрын
Hi you done great job I have Cleopatra same as yours it’s got Volvo Aq145 and I’m thinking to change to on 606 and yeah idea when can I get the conversion or the website you bought the heat exchanger and what hp How many knots you could do many thanks
@STRACHU1002 жыл бұрын
Thanks. How fast will she go is a bit of a gamble, with 4,6 l volvo she could make around 30 knots as I read. With this one I am hoping to reach 25 knots which will be more than enough for me. If I ever wanted to go faster I can always supercharge the engine (as I understand OM606 can be boosted up to as much as 600 HP!) As for the conversion parts I can PM it to you as puting it here is not entirely legal. just send me your email adress. Cheers
@adelkandil4069 Жыл бұрын
Hi mate hope you all well man I got a few questions to ask man if I can get in contact with you many thanks
@STRACHU100 Жыл бұрын
sure, write to my email
@MarcinSzifo2 жыл бұрын
Marzy mi się taka łajba do remontu. Jeżeli to nie tajemnica ile ta piękna kosztowała?
@STRACHU1002 жыл бұрын
żadna tajemnica- kupiłem bardzo okazyjnie- 1000 funtów. kilka lat temu. Właściciel boatyardu chciał po prostu zwolnić miejsce. potem chyba trochę żałował. W UK jest tego sprzętu bardzo dużo więc takie starsze łódki do remontu są często dostępne. powodzenia w poszukiwaniach.
Greetings, Can u share infos about heat exchanger...how many kw ? Or some details...thanks
@STRACHU1002 жыл бұрын
Hi, its 150kW, the rule is relatively simple: it must always have more kW than the engine (around 10-15%) this one is made exclusively of stainless steel which is rare. could give you hints where to find it on PM as writing it here is not exactly legal
@Coisaka2 жыл бұрын
@@STRACHU100 i will appreciate to pm me ...just to see if the price is competitive to our domestic prices... Thanks for knowledge,i didnt know how to determine size of exchanger
@Krzemieniewski1 Жыл бұрын
Część! Zrobiłbyś dla mnie marynizację?
@STRACHU100 Жыл бұрын
Cześć, Wyślij mi swój kontakt na maila, napiszę Ci jakie są możliwości
@eesabal15419 ай бұрын
Hello how did you make this engine marine?
@STRACHU1009 ай бұрын
thats what the movie is about...
@noweguty16462 жыл бұрын
Można prosić o jakiś kontakt? Remontuję właśnie taką Kleopatrę, identyczną. Potrzebuję kilku informacji
@STRACHU1002 жыл бұрын
jasne, proszę o kontakt, dane można znaleźć w zakłądce "about"
@noweguty16462 жыл бұрын
@@STRACHU100 nie wiem jak to znaleźć, szukałem kontaktu
@noweguty16462 жыл бұрын
Może pan napisze do mnie na maila
@STRACHU1002 жыл бұрын
@@noweguty1646 w Pana profilu nie ma danych kontaktowych
@przemekwojs9712 Жыл бұрын
Można prosić o kontakt???
@STRACHU100 Жыл бұрын
jasne, mój email jest w zakładce "about"
@przemekwojs9712 Жыл бұрын
@@STRACHU100 niestety nie ma w zakładce about jest tam tylko Drones Boat restoring i jeszcze kilka innych opisów
@STRACHU100 Жыл бұрын
@@przemekwojs9712 ok email: strachu@interia.eu (nie wiem, czemu nie widać, u mnie jest)
@paletyszczecinskupsprzedaz2 жыл бұрын
Kolektor wydechowy będzie chłodzony wodą?
@STRACHU1002 жыл бұрын
docelowo tak, chociaż to jest spore wyzwanie, musiałbym go upchać pod wymiennikiem ciepła, poza tym najlepiej byłoby go wyspawać ze stali nierdzewnej a to dosyć trudne. na początek pewnie użyję oryginalnego kolektora mercedesa a wodę chłodzącą układ spalinowy wprowadzę za turbiną. najlepszym rozwiązaniem jest kolektor chłodzony zintegrowany z wymiennikiem, można takie kupić gotowe ale koszmarnie drogie!!!
@paletyszczecinskupsprzedaz2 жыл бұрын
Mogę udzielić parę cennych wskazówek,mam taki silnik w lodzi …
@STRACHU1002 жыл бұрын
@@paletyszczecinskupsprzedaz dzięki, chętnie skorzystam, mogę prosić o kontakt PM na maila?