Thanks AC for continuing to share the knowledge. Priceless stuff
@mr.buttons84864 ай бұрын
Thank you Sir
@Markycarandbikestuff3 ай бұрын
Hi AC great stuff, have subbed, quick question, will i be ok fitting an old 12G202 head on an 88 A+ 998 motor ?, it's a really nice big valve ported job, plan to eventually use this with a Kent 266 Cam, LCB and decent single box center exit system.
@ACDodd3 ай бұрын
Yes ideal you will loose a little compression but not a huge amount
@Markycarandbikestuff3 ай бұрын
@@ACDodd Cheers for that, seller did say head had been skimmed.
@Slack3rDav34 ай бұрын
a before and after drive video example would be wonderful
@ACDodd4 ай бұрын
This is very difficult to achieve.
@luismeixner21254 ай бұрын
AC, how do you check if the vacuum advance is working? little suck on the pipe whilst watching the advance on a strobelight?
@ACDodd4 ай бұрын
You got it, however you’ll likely to get fuel in your mouth!!! A vacuum pump is a much healthier way to check!
@supremefox23464 ай бұрын
What should be the target af/r on idle and when revving on a 1098cc with a stage 1 kit
@ACDodd4 ай бұрын
I offer training for those that wish to be able to tune carbs themselves.
@dominiccooper8104 ай бұрын
AC, any chance you could show how to by pass the ballast resistor? I’m fitting 1275 motor electric 65 d dizzy into a 76 mini scamp. It used to be 998. It did have a 3ohm coil but I’ve a 0.8 now cos of the dizzy. I’ve got no clue on wiring. Thanks
@ACDodd4 ай бұрын
Has your scamp got a ballast resistor in the loom?
@dominiccooper8104 ай бұрын
Hiya AC, thanks for the quick reply. I don’t know if it’s got a ballast resistor in the loom or how to check if it has. Thanks
@ACDodd4 ай бұрын
@@dominiccooper810ballast wire is white/pink. If the wire that feeds the coil is white you good.
@george50224 ай бұрын
AC, What voltage coil 12v 3A or 8v 1.5 A - on a blasted system ? its not specifically for mini but mgb.
@ACDodd4 ай бұрын
A ballasted system uses a 1.5ohm coil for a 4 cylinder engine.
@george50224 ай бұрын
@@ACDodd Thanks for the reply, so it should have a 12v coil with 1.5 ohm not a 8v coil 1.5 ohm
@ACDodd4 ай бұрын
@@george5022it’s not 8volt anything, it’s a 1.5ohm coil
@nevhath4 ай бұрын
AC. Do you recommend fuel stabiliser with every tank of fuel. I'm running a 1310cc with your RS+ cam and a 45 DCOE Weber I always use Shell V-power
@ACDodd4 ай бұрын
How long do you leave it between using it?
@nevhath4 ай бұрын
@@ACDodd Use it regularly this time of year. Normally park it up when weather turns...(October time) I do add fuel stabiliser then when it's parked up over Winter. I use STA-BIL. I think on your recommendation..
@ACDodd4 ай бұрын
If you leave it longer than 1 month it needs stabilising. Stabil make a produce called stabil 360 which is designed to be used every fill up.
@nevhath4 ай бұрын
@@ACDodd Thanks AC.
@pablojimenez83294 ай бұрын
AC, How do you normally detect a leaking intake manifold/carb? What are the symptoms and how can you confirm the leak?
@ACDodd4 ай бұрын
Use a can of brake cleaner and spray it on the joints with the engine running. if the rpm changes it’s leaking. Revs rise carb is set lean, revs drop fueling set much too rich
@troypowell16714 ай бұрын
what leads do you recommend for a 08 coil with pertronix 59d dizzy and bp6 plugs gapped at 35tho and what ohm reading would be acceptable
@ACDodd4 ай бұрын
I use Powerspark 8mm leads having a resistance of typically 1.5 to 2kohms per lead.
@troypowell16714 ай бұрын
@@ACDodd copper core or the other kind
@ACDodd4 ай бұрын
@@troypowell1671not copper core
@ColinSpencer4 ай бұрын
How do we get in touch with you and do you come to Lincolnshire?