I have a p216 onan on my welder with the same problem if i give alittle chock it will wuit and once it runs for awhile i can take the choke off and it runs like new .my guess is the carb needs a good cleaning she is 25 years old now and been rode hard without much maintenance at all just gas and oil and for the last couple of years she has just set quite abit.todays gas really sucks.going to clean her good after this job is done hope she makes it that long.
@DickWheels3 жыл бұрын
If it will run with choke then it's lean and most likely carb related.
@adamwaller1528 Жыл бұрын
When the engine is off should the tension spring be keeping the governor against the screw or off of it?
@georgecolbert32473 жыл бұрын
I had the same problem with my 520 with the snowblower hooked up. Seems like the air bleeds get clogged up and its difficult to get them clean. It would only happen at full throttle or under a load.
@DickWheels3 жыл бұрын
These cards are a real pain in the ass. The engine is extremely picky too
@JCunningham21Ай бұрын
can that carb be rebuilt on the engine? I have a Ingersoll 3016 doing the same.
@isaactorowheelhorse518h44 жыл бұрын
Right next to the carburetor there's a adjustment screw just trying to adjust a little bit and the loving will stop
@DickWheels4 жыл бұрын
That's just the idle mix screw. Although opening it about 5 turns helps, it doesn't idle well as its way too rich. It's also not the right thing to do and indicated there is an issue elsewhere
@mrl76614 жыл бұрын
DickWheels so, the only other way it can be surging is if they manifold gasket is leaking.
@kenchasser43763 жыл бұрын
Looks like your governor return spring is in the wrong hole. Should be in the third hole from the pivot, then adjust your carb properly. Air mixture screw should start out at 1 1/2 turns from closed position, then turn either way at 1/8” increments as needed.
@DickWheels3 жыл бұрын
I moved it to get more rpm. It took a few carb cleanings and then turning the screw out more then 1.5 turns.
@hunter74762 жыл бұрын
@@DickWheels shouldn’t do that could get to much rpm and ruin the engine
@hunter74762 жыл бұрын
Could be an intake leak the intakes on these are silicon on the middle to seal it might be leaking air causing an air to fuel issue or your float could have a hole in it or the needle is not sealing properly or the float level could be off or maybe just dirt in it
@reggieanderson88511 ай бұрын
It’s not an intake leak… he tested it by spraying parts cleaner on it
@hunter747611 ай бұрын
@@reggieanderson885 I guess but it’s not an accurate test a better way would’ve been a leak down tester and blocking off the intake.
@reggieanderson88511 ай бұрын
@@hunter7476 quick troubleshooting..
@will7its10 ай бұрын
I took mine off and filled it with water and it was pissing all over the place....lol
@66Oliver21 күн бұрын
That’s why it’s hunting. He hasn’t adjusted the governor to run in the new position. I had a bent throttle arm going to the carb on an Onan P218G, and it did exactly this. Bent the arm back up, and presto, problem solved.
@shelbowwow14902 жыл бұрын
Would you happen to know the part number of that oil dipstick? The oil cap broke, ive just bought it from a previous owner.
@DickWheels2 жыл бұрын
I do not. Sorry
@hunter74762 жыл бұрын
Look up your tractor model on parts tree and you’ll find the oil cap
@georgem.kokindajr.941Ай бұрын
What is that stuff you’re spraying on the intake manifold, and why? I have a problem with my J Deere 316 P2 Onan surging.
@Junkboy88811 күн бұрын
He is spraying a flammable fluid like brake cleaner around the Manifold and listening to hear of there is an increase in engine RPM. If there was a air leak the will idle up. Surging is generally . cause be an improper mister of air and fuel
@paulg4444 жыл бұрын
So what was the solution ?
@DickWheels4 жыл бұрын
That new carb in the video was from a 520. No matter how I jetted it it just never worked right. I found another correct carb and after a good few day soak in cleaner then into the ultrasonic...she is fixed.
@OldMotorcycleAdventures2 жыл бұрын
@@DickWheels I'm going to have to buy an ultrasonic. Got a B43E on my John Deere that's been kicking my ass for years. Got it to run perfect the other day after revealing the intake, now it's back to sputtering and running like crap. I have tried 2 carbs, which both were freshly cleaned out with air, brushes, simple green the other day before I put either of them on the tractor. Beyond frustrated with this thing, haven't been able to mow my own lawn with it
@M.O.T.H._51H84 жыл бұрын
2 term Trump #maga #2020
@Sluggo012 жыл бұрын
Trump would never let Ukraine be invaded
@alanmccalla6737Ай бұрын
As I see, you posted 4 years ago. He lost then. There was no evidence of the steal. And yet Frump is going to try yet another time. "Experience is a dear school and fools will learn in no other."