ONLY 2 STEPS TO FIX ORBITAL SANDER with unstable RPM

[@charlesschuster7963]

Thank you John for a well executed repair. 1. You cleaned the commutator, not the "connector" and I'd use sandpaper coarser than 800 or 1000... try 400 or 320 grit and it will clean up sooner and easier. You're right about all random orbital sanders being constructed the same, I have a Ridgid R2601 apart and it's similar, with the bottom bearing going bad. 2. The plastic or rubber seal on the bottom bearing can be removed (sometimes) using a sharp tool, then the accumulated dust removed from the balls. Lube, reassemble and good to go, if the bearing wasn't too far gone in the first place. 3. WD-40 is NOT SUITABLE for bearing lubrication. Use a thin white grease or similar, but will need to get in inside the bearing since the seal will mostly prevent it from getting there by itself. 4. Cleaning power tools every 3-6 months in a shop environment is far too frequent (in my opinion). Well designed power tools may accumulate dust, but should be able to function indefinitely without such cleaning. Clean it makes you feel good but no under the misconception that it will "improve" things. I clean mine only if a failure requires me to disassemble the tool.

[@00AdamWindings00]

Really appreciate your in depth explanation, you helped keep me from spending another 50$ on a new sander

[@ifoleyienationchannel4779]

Thanks for this video. You saved me $140 Canadian for a new sander. My bearing was jammed up with dust. Added WD40 and that was the fix.

[@bethlaurence5781]

Thanks for the great video and info. I was able to fix my B&D orbital sander that was reviving unevenly.

[@Tshepo-km3fn]

Thubs up, I just did mine, the lower bearing couldn't turn after watching this video I was able to fix it and now it's working perfectly

[@larissalind2872]

Great video!!! I love how I could see exactly what you were doing, and how you kept things nice and simple. Thank you so much!

[@s7inspirasi841]

Very informatif, thanks bro,. Actually how many months should I give light mantainance for powertools, while i'm just weekenders woodworker?. Thank U.

[@jhonarief]

I Think 6 month that would be good time period

[@s7inspirasi841]

Thanks 🙏 for reply.

[@rodneyneff5965]

I appreciate the video they had great insight mine's just going way too fast I'm going to try this and see what happens. ps. after you put the WD-40 on it you should rinse it off with rubbing alcohol that way it doesn't collect the Dustin do this twice as fast.

[@carmelgrace6402]

Thank you, you gave me the courage to open up my sander .. i had drop mine..AH, all that was wrong was a wire had disconneted.. thanks again😀😂

[@alxhrrs]

Ok, your video just saved me 140euros. Not exagerating, my problem was the bearing, the one you sprayed with wd40. Same thing for me, I sprayed it and now it works. My problem was that when I set it down on the wood, it wouldn't turn, but if I lifted it off the wood it would spin fine. My question at this point is, did this happen because I sanded down boards with grain filler/stucco on them? Did the chalkey dust get into the bearing?

[@fr0stedcake]

Im sorry i was frustrated. Your video was very helpful.

[@g3channel.]

Aq aj yang Pertamax yaaa.....thanks my brother...keep spirit 👍🏻👍🏻👍🏻👍🏻🙏🙏🙏🙏🙏

[@jhonarief]

Thank you mas 🙏👍

[@warga62plus]

Lah bro nyampe jg disini 😂

[@reggie7922]

Thank you so much sir great job well done I have one to fix myself and I am going to use your method instead thanks again

[@jacqueayars603]

Thank you very much for your help on this video !

[@shamishak7150]

Alhamdulillah bosskur... excellent job

[@PinoyMusicRevolution]

Thanks!

[@LiviuGelea]

you should use a lubricant instead of a water displacer. WD40 only lubricates for a few weeks until it evaporates, burns or otherwise gunks up. Additionally I would never "clean" the rotor contacts. That layer is not oxides, it's just graphite buildup from the brushes. At least use a finer sandpaper and just remove a thin layer, don't make it fully "clean". Good advice in general though. We would all save some money if we just cleaned our parts more often instead of runing them into the ground.

[@mubeenebrahim5445]

Alhamdulillah that was very useful

[@mubeenebrahim5445]

I literally tried this after watching the video and it works amazingly.

[@gabrieltunia2073]

Please make your voice lauder on thise videos because it is hard to hear it when machines are working.

[@williamcunningham1614]

Thank you.

[@Kiltedwoodsmith]

Salamat Po

[@Yusmaidi-wb2zw]

Hadir masbro👍

[@jhonarief]

Makasih banyak maskuu

[@radiantresnasumaatmaja6164]

Lah cetek juga kirain bakalan agak susah kaya yg merk makita,,merk aldo kayanya sama aja dgn dekwe deh.

[@warga62plus]

Pertamax bro

[@boyrusi]

Sirr magtagalog ka nlng para mas mabilis maintindihan

[@helmi_varotex]

Pertalite gpplah

[@noelbaluyotbaluyotnoel-po5mc]

Dikaba marunong mag tagalog boss ?

[@PrincernPrince]

Thanks but God awful sound