Opel / Vauxhall Corsa C P0335 crankshaft sensor replacement guide.

  Рет қаралды 562,770

Fred in the Shed

Fred in the Shed

Күн бұрын

Пікірлер: 206
@tmakahavok
@tmakahavok 7 жыл бұрын
Did this today with a jack and two axel stands and it worked. Saved me £200. Hardest part was getting the sensor out as hands are too big and there's very little room to work with in general. Thanks for uploading the video made this easy.
@CB-RADIO-UK
@CB-RADIO-UK 7 жыл бұрын
Pleasure and well done
@graemerobertson5160
@graemerobertson5160 8 жыл бұрын
Thanks for taking the time to make this video, I followed it and got rid of starting and stalling problems.
@paulster2686
@paulster2686 9 жыл бұрын
Great video. I would just add, a small amount of lubricant (clean engine oil) on the sensor and o-ring will help tremendously when re-inserting it into the block.This will also help in seating the o-ring without damage.
@shaun27ful
@shaun27ful 9 жыл бұрын
I'm sure someone out there will be very glad of that advice great video buddy.
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
shaun pi Thanks mate
@andrewpenketh5498
@andrewpenketh5498 5 жыл бұрын
Did mine today on my 1.7 DI combo van. It was a git to get to. Just underneath starter motor and above driveshaft. There was also a starter motor bolt right in line of the bolt (hence why I needed the 1/4 drive universal joint😟 Mine was an M10 bolt. The only way I could get to it was a 1/4 drive socket, universal joint and 100mm extension bar.... not easy at all. Very fiddly. The good news is it’s now purring like a kitten. I also changed out the EDU on back of engine ( fuel control brains). They both give same symptoms. Sending my old EDU off for repair on the eBay advert (£40.00 with lifetime warranty) Great video... very helpful
@MrBazdamic
@MrBazdamic 3 жыл бұрын
Hello, can you please give me the sensore code please!??
@Kefo11
@Kefo11 2 жыл бұрын
What's an EDU? As i changed this with a new one and it's the same problem again...
@1969Spursgeezer
@1969Spursgeezer 3 жыл бұрын
Thanks for this video you just saved me a garage bill 👍🏻
@jameslegrange196
@jameslegrange196 2 жыл бұрын
Gold video Fred! Appreciate your attention to detail! Wish me luck!
@CB-RADIO-UK
@CB-RADIO-UK 2 жыл бұрын
Good luck!
@lzh2382
@lzh2382 6 жыл бұрын
The best explainer men at all the times
@pollyheenan4283
@pollyheenan4283 6 жыл бұрын
I will change That 😂😂😂
@tutting
@tutting 5 жыл бұрын
Thanks for your video, nice & clear, making it an easy job to complete!
@shauneking7152
@shauneking7152 2 жыл бұрын
Really admire your efforts in these videos. Very well explained, detailed A+1 keep up the good work especially on corsa, just bought 👍 one and love it so please 🙏 hope your video's help me. I really wanna modify this car
@kam5638
@kam5638 8 жыл бұрын
this video saved me so much time and let me know what I was in for. Job not quite as bad as I expected. Huge thanks
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
No probs :-)
@grahamewilliams6642
@grahamewilliams6642 5 жыл бұрын
Thank you for the upload, exactly what I was looking for, hopefully it will help sort the problem
@Love500
@Love500 7 жыл бұрын
Thanks. Good clear video. Will be doing my sister in laws at the weekend.
@EASTLONDONPIMP
@EASTLONDONPIMP 8 жыл бұрын
top man! I was told £300 to do this its so simple. thumbs up
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+EASTLONDONPIMP Jeez tell me about South East prices. Its a little awkward job but cheap if you DIY. ;-)
@EASTLONDONPIMP
@EASTLONDONPIMP 8 жыл бұрын
fredintheshed1 want to do mine? lol
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+EASTLONDONPIMP Nah that's why I made the video for you to have a go. Hardest part is getting the old one out if its the orig part as it can be tight. Also let the cars exhaust cool down. You can do it.
@QRAC222
@QRAC222 5 жыл бұрын
Great video, perfect execution! Thank you very much!
9 ай бұрын
Thanks, it's exactly the SAME ON ASTRA H 1.4 PETROL!
@Tobinindustrial
@Tobinindustrial 9 жыл бұрын
Thanks for sharing. My dad owned a Vauxhall way, way back in the day. I don't believe they sell them here in Canada anymore and I suspect it was an import when he bought as we were a colony of Great Britian before Confederation with Canada in 1949.
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
Andy Tobin Hi Andy. They are sold worldwide under the Opel brand. Vauxhall has a huge plant in Luton UK which is just a few miles from me. I think the Corsa was made in Spain though.
@jamess4878
@jamess4878 4 жыл бұрын
Thanks very well explained.
@CB-RADIO-UK
@CB-RADIO-UK 4 жыл бұрын
You are welcome!
@adhamalfdany4613
@adhamalfdany4613 2 жыл бұрын
Hello Can you pleas tell me where is a crenk shaft sensor for OPEL VEVARO 2.0DCiM9R 2011 and thank you
@CB-RADIO-UK
@CB-RADIO-UK 2 жыл бұрын
Hi sorry i have no idea. :-( Maybe try a Opel car forum. Best of luck.
@jelleuyttersprot3888
@jelleuyttersprot3888 5 жыл бұрын
Thank you for the video. Fixed my car with this. My Tigra Twintop wouldn't start. OBD said crank position sensor. Fixed in 5 min. time
@bradleighdavies4645
@bradleighdavies4645 9 жыл бұрын
You save me money and time I was told different it would off cost me over 100 but only £15 I paid :)
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
+Bradleigh Davies Glad to hear, that's the idea. ;-)
@tobyyoung6321
@tobyyoung6321 3 ай бұрын
I believe my o-ring came off in the block and I have tried everything to get it out, new sensor goes in but everything since I've gone through 3 of them. Any tips?
@hundui
@hundui 6 жыл бұрын
Perfectly explained Thanks man
@bcmaughan
@bcmaughan 6 жыл бұрын
Top video Fred thanks. I'm also in Somerset like the last commenter and looking to replace mine! Is this procedure the same for an astra g 1.7 dti? I don't have code 0335 but have 0370 and 0400 too. Reason I think it's maybe crank sensor is because when engine is warm and driving on very light constant throttle the car doesn't maintain a constant speed but seems to surge forward intermittently. Diesel consumption seems a little high too.
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Once the engine losses its crank sensor it can throw up all sorts of codes as its totally lost.
@bcmaughan
@bcmaughan 6 жыл бұрын
Thanks Fred. Similar location and access on the astra 1.7dti isuzu or is it not an engine you know?
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Not sure Ben. Its going to be down low as it uses a magnet on the crankshaft.
@bcmaughan
@bcmaughan 6 жыл бұрын
@@CB-RADIO-UK cheers Fred ta
@alunroberts1439
@alunroberts1439 Жыл бұрын
Thanks so much I was 1st given wrong information.
@naimovicartsbrussels
@naimovicartsbrussels 4 жыл бұрын
Many thanks. 100% correct.
@markyyyy7
@markyyyy7 Жыл бұрын
On my Corsa C I only get the spanner light when the car has been running 20 odd mins, giving the crankshaft sensor fault, it never comes on from cold and the car runs perfectly, any thoughts??
@CB-RADIO-UK
@CB-RADIO-UK Жыл бұрын
It does sound like its breaking down when hot under load. What normally happens is that it will get worse till the car will not start as the car wont know where the crankshaft has stopped.
@markyyyy7
@markyyyy7 Жыл бұрын
@@CB-RADIO-UK any idea what could be causing it?
@mikenow3050
@mikenow3050 9 ай бұрын
Excellent video how it should be
@TomBurns94
@TomBurns94 9 жыл бұрын
I have just replaced this but I am now having a problem with the radiator fan. When I turn the ignition on the fan starts on maximum and continues when the engine starts, I have a error code of p0115. Any help would be appreciated.
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
+TomBurns94 Sounds like the thermo temp switch may have failed. The ECT (Engine coolant temperature) sensor is basically a thermistor that changes resistance with temperature. Usually a two wire sensor, a 5Volt reference from PCM (Powertrain Control Module) and ground signal to PCM. This is different from a temperature SENDER (which usually operates the dash temperature gauge and operates in a similar way as the SENSOR, only it's a different circuit than what a P0115 is referring to). As the temperature of the coolant changes, the resistance changes on the ground signal to the PCM. When the engine is cold, the resistance is high. When the engine is warm, the resistance is low. If the PCM detects a voltage condition that seems abnormally low or high, P0115 will set.
@RSPYT
@RSPYT 8 жыл бұрын
I love a simple job. Currently have my Focus apart dude, the work never ends lol.
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+RustySkull Productions Yeah that's true mate but think of the labour cost that you save.
@RSPYT
@RSPYT 8 жыл бұрын
True.
@rerhanuddin6464
@rerhanuddin6464 8 жыл бұрын
very well explained, thank you ever so much!
@usmanrabbani2062
@usmanrabbani2062 7 жыл бұрын
worked like a charm. thanks a lot.
@MHISD
@MHISD 8 жыл бұрын
brilliant video! very helpful and well explained
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
Cheers Antoan.
@cantnotfind
@cantnotfind 8 жыл бұрын
Hello bro, i have a corsa c 1.7 dti disel but it's not working good, i want your opinion about my case, before it was very speed when the "Rotation" when to 1.8 or 2.0 the turbine started working and the speed was increased to very fast, now when i drive it's going very slowly and the rotation passes 1.8 , 2.0 and more but it's not taking any effect, i changed turbine , it's still the same, i tried with new AIR SENSOR it's still the same, my question is : is there any another SENSOR that i need to change to fix this problem? Thanks!!!
@MHISD
@MHISD 8 жыл бұрын
i have petrol corsa c 1.0 which is obviously very different engine than yours. The engine was very slow to response and sometimes it dropped the revs suddenly for a few seconds. After i changed the crankshaft sensor it's a lot better and don't have the same problems anymore. I would suggest to check the engine faults on your car first to be sure what is wrong rather than replacing everything that comes to your mind. Good luck :)
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
Yes I agree with Antoan. It seems your turbo is not producing boost or perhaps the waste gate or turbo ducting is leaking pressure. Either way you are prob best to get it checked out on a rolling road. Have you tried putting this out on a Corsa forum.
@cantnotfind
@cantnotfind 8 жыл бұрын
Antoan Hady, Thanks for your reply bro! i already controlled everything regarding motor mechanic and the service told me that they don't work with sensors and electricity in the vehicle, but they confirmed everything else that is ok, also turbine was tested in another car and it was working good.. i think the problem is to sensors , but i'm not sure which sensor exactly is not working because i have to order it from ebay or somewhere..
@aminazoi1079
@aminazoi1079 9 жыл бұрын
Thanks for sharing ,very helpful ,now I m going to try on my car as its broken down because of that fault ,,let's c ,,thanks again for helpful advise
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
Amina Zoi Your welcome. As I mention on the video its a little cramped space to work if your laying on your back. The sensor may be a little tight in the block if its the original so take your time levering it out. Our Corsa has been running 100% since this video.
@doug12341988
@doug12341988 9 жыл бұрын
I had this problem and paid a mechanic like £120 to fix it. Wish I had watched this video first!
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
+doug12341988 Don't worry we have all done things like that. Its an easy fix but the work area is tight.
@thomasdalton-locke305
@thomasdalton-locke305 5 жыл бұрын
Thanks for the great video! I'm almost there... I just can't seem to pull the old senser out. Bolt out, covered the lot in wd40, went at it will a long flat head screwdriver driver, but it just won't budge! Any suggestions before I send it off to the mechanic?
@CB-RADIO-UK
@CB-RADIO-UK 5 жыл бұрын
Its a problem as they get stuck. Not much you can do other than use a pry bar to try and get it moving. What you dont want is it breaking off and dropping inside the engine. If its really stuck than it might be best to let the garage change it.
@VVVhitesnake
@VVVhitesnake 3 ай бұрын
Hi Guys, Do you know what is the part name number for this Crankshaft Position Sensor A Circuit when ordering the part? Thanks
@chum-games
@chum-games 3 күн бұрын
GR9 VIDEO! Thanks
@mukateko4535
@mukateko4535 7 жыл бұрын
thank u my opel has just that problem i think thanks again!!!!!
@CuddlyJ
@CuddlyJ 2 жыл бұрын
Can you please confirm the part required for a crankshaft position sensor there seem to be lots of options even when putting in the reg number. I have a 2005 Vauxhall Corsa twin port 1.2. LX05OGR thanks
@CB-RADIO-UK
@CB-RADIO-UK 2 жыл бұрын
Hi. No sorry the car was sold on many years ago.
@astralgary.
@astralgary. 5 ай бұрын
Hi, do i have to disconnect the battery before changing the sensor.? Will the new sensor confuse the ECU. Thanks
@CB-RADIO-UK
@CB-RADIO-UK 5 ай бұрын
It should not. I just had the ignition off and did not have an issue.
@neilwalsh4058
@neilwalsh4058 6 жыл бұрын
What a great video, just changed the CP sensor on my sons Corsa and this was very helpful firstly to locate the sensor and the nice tip about an 8mm ring spanner. I have the torks sockets but it difficult to get one on where the sensor is. Gave it a 4 mile test run thro town and didn't get any of the stalling at junctions he had before. The engine management light stayed on tho after the new sensor and throughout the test run , but cleared the next time I started the car. Maybe the ecu learning the CPS is now good?
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Well done Neil. You prob saved £100+ labour charge.
@dennis12879
@dennis12879 3 жыл бұрын
mate could you please advise me i cant get mine off the hole bot broke off and cant lift it i put some wd40 on it but it dont seem to help if anything seem to get stiffer to move i tryed sopy water that never helped do you have any idea thanks dennis
@CB-RADIO-UK
@CB-RADIO-UK 3 жыл бұрын
Might try some gentle heat.
@dennis12879
@dennis12879 3 жыл бұрын
@@CB-RADIO-UK would it help if i started the for 5 minutes or just best to use heat gun thanks dennis
@jeremyplested7988
@jeremyplested7988 2 жыл бұрын
Mine broke inside and now is stock in the drive shaft ! How can I remove it spent 6 hours and still has the plastic in there 😢 please help
@CB-RADIO-UK
@CB-RADIO-UK 2 жыл бұрын
Only way i see is to start stripping the motor from the bottom. :-(
@LivinLars
@LivinLars 8 жыл бұрын
Hello, nice guide! Did your vehicle flash F? Mine does and I'm suspecting it's this sensors fault as it sometimes starts without trouble and sometimes just flashes f. Feels like a sensor fault then the whole actuator.
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
I am not sure if it flashed. Its my daughters car. She stopped to get fuel the car being hot and it would not start. The EM light stayed on. It started and I read the code.
@leetaylor3004
@leetaylor3004 8 жыл бұрын
fredintheshed1 is the crankshaft sensor located in the same place on a combo 1.3cdti as the video ??
@TheCheetahang
@TheCheetahang 8 жыл бұрын
hi just bought obd2 scanner 2015 model.when I scan it says not compatible dtc something like that.any help?
@marksealeycalibra
@marksealeycalibra 9 жыл бұрын
very nice...i need to do this on my calibra c20ne engine......ecu code 31....the sensor is at the front near the pass pump.
@Daz1962
@Daz1962 6 жыл бұрын
Will this also fix the 'f' code problem - also apparently caused by a crankshaft sensor fault (according to multiple google searches)? Thanks - great video.
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
TBH not sure. When the crank sensor fails it causes all sorts of issues and the computer has no idea of the engine timing.
@enigmalex3649
@enigmalex3649 3 жыл бұрын
I replaced crankshaft sensor on my Opel Tigra. Error code was also deleted and I had the same problem as before it stals in idle and error code for cfrankshat sensor still comes up.
@CB-RADIO-UK
@CB-RADIO-UK 3 жыл бұрын
Maybe its something else. Try driving it a few times and search for codes.
@enigmalex3649
@enigmalex3649 3 жыл бұрын
​@@CB-RADIO-UK Thanks for the replay. Also I noticed that my speed senor doesn't work. I will try to change it also maybe that sensor is causing the problem. They working on the road where I live and after I drove a few times on that road problems with sensors started.
@JasonAlexander-n8t
@JasonAlexander-n8t Ай бұрын
Can I use lithium grease on this to get it in? I can o lay get it in with about 2 mm gap
@CB-RADIO-UK
@CB-RADIO-UK Ай бұрын
Yeah should be fine.
@JasonAlexander-n8t
@JasonAlexander-n8t Ай бұрын
@CB-RADIO-UK thanks mate!
@pollyheenan4283
@pollyheenan4283 6 жыл бұрын
Omg great video.....unjust tested my car and I need to replace it but I'm to scared to do it my self lol.....how much would a garage cost ??
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Depends on where you live. Rough guess £90-140
@gazfcgruff
@gazfcgruff 9 жыл бұрын
Thanks for the vid, gonna change mine soon as I'm having poor warm starting, although I get no error codes. Is this normal?
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
gazfcgruff We got a error code with ours the first time it refused to start. Without a code you wont know if its the crank or the camshaft sensor as both have similar symptoms. If your used to working on your car then its a cheap part to change and remove it from the problem.
@gazfcgruff
@gazfcgruff 9 жыл бұрын
fredintheshed1 once again thanks for the tut, just changed mine, the plastic around the connectors had pretty much broken off on one side, hopefully this will sort my probs out
@teodormihai2244
@teodormihai2244 2 жыл бұрын
Hello mate ! I got 0300 and 0302 error missfire on my corsa 1.0, and i was thinking it can be also the crankshaft Position sensor a Problem to this error ? Coil Pack is New, ignition also New, injectors no error, but second injector if i pull out the harness, the engine mentain the same nothing else happening.... I am broke, can you help me ?
@CB-RADIO-UK
@CB-RADIO-UK 2 жыл бұрын
Its hard to say TBH.
@MiloDavis93
@MiloDavis93 7 жыл бұрын
If you don't have a code reader and the fault light is on, you can use the pedal test, requires no equipment at all, just Google vauxhall corsa pedal test
@TaipansEmporium
@TaipansEmporium 6 жыл бұрын
Very helfpul video. Thanks.
@kpfrisby9
@kpfrisby9 6 жыл бұрын
my 2005 corsa c was cutting out at junctions after warmed up so checked fault codes and wasnt showing any but had an idea it was the crank sensor so i changed it and all seemed fine til the next day and the engine was now misfiring and showing a fault code of crank sensor and a cyl down as well as emissions out, it wasnt misfiring before i changed the crank sensor just cutting out, could this be a faulty new crank sensor ??
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Yes. The crank sensor i fitted in this video failed after 2 weeks. I bought a gen sensor from the the dealer and that one worked ok. The cheaper ones have quality issues.
@wacka2
@wacka2 8 жыл бұрын
hey there , i have the diesel , i have read the fault code using the pedals and it shows P0335 (CPS ) , but the engine management light is not on all the time and the vehicle runs perfectly fine , it normally would only come on when under load , ie , going up a steep hill ..........would you suggest that the crank pos sensor is failing , if the van runs perfectly well and has done for months ?
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
A P0335 fault code indeed means the crank sensor is going open circuit, on that i would change it. They normally start to fail intermittently when the engine is hot and shut down then a restart is tried. That normally triggers the engine light. If a failing sensor would put the light on under heavy load, iam not sure, that could be something else. Maybe a cheap ebay OBD 2 code reader is a good idea. Good luck
@wacka2
@wacka2 8 жыл бұрын
thanks
@artotiainen5700
@artotiainen5700 7 жыл бұрын
do i need to take engine oils out before i change the sensor???
@CB-RADIO-UK
@CB-RADIO-UK 7 жыл бұрын
No the sensor is above the oil line.
@djfat2para205
@djfat2para205 7 жыл бұрын
Need help! as I was taking out the old sensor the old bolt holder snapped and left the sensor still in and can't enough grip on the sensor to pull out. Any suggestions? Great vid BTW
@CB-RADIO-UK
@CB-RADIO-UK 7 жыл бұрын
Mine was tight as well. You need to carefully pry around the edge with a screwdriver. Once you have a gap spray in some wd40. Just take your time.
@clara17uk
@clara17uk 8 жыл бұрын
hi fredintheshed1 is this the same location on a meriva 1.4 petrol ,it took me 3 days to find the obd thingy to plug in the fault finding machine it looks easy even im gonna try it,great video
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
Not really sure on the Meriva. The crank case sensor is going to be somewhere on the bottom of the engine block. The sensor itself and fitting is prob the same.
@clara17uk
@clara17uk 8 жыл бұрын
ok thanks for the reply,i will take them all out and clean them,till i find the right one and replace it , many thanks for all your help,godbless you fredintheshed1
@Mr-nt8mz
@Mr-nt8mz 6 жыл бұрын
Hi there I'd like to ask you something if I may, I have a ZAFIRA 2.2dti from 2003 and I have the same error you got so I bought a crankshaft sensor and plan on installing it tomorrow. But from my obd I also have an error "P0340 camshaft position sensor "A" circuit (bank 1 or single sensor)" I am hoping the injection pump is not dying because it's worth more than the car now. Do you think the second error could be caused by the 1st one? Thanks if you can help ;)
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Yes its possible if the crank sensor has failed it might upset the Cam sensor as the CPU will have no idea where the engine has stopped. I would install the crank sensor and reset the codes and see if the EM light comes back on. If you get the 340 code again then the cam sensor is also failing.
@Mr-nt8mz
@Mr-nt8mz 6 жыл бұрын
fredintheshed1 Thanks ;) I'll go ahead with the crankshaft sensor and test drive. Hoping that will be it. Have a nice Easter weekend!
@ThePhonecat
@ThePhonecat 9 жыл бұрын
hello mate, I have an Astra G which shuts off when it warm . Then struggles to start. it starts perfectly when cold. However I have got no codes showing?
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
+ThePhonecat Normally a crankshaft or camshaft sensor fail will store a code. Have you tried plugging in the scanner when the car wont start. Basic stuff also helps starting like a clean air filter etc.
@ThePhonecat
@ThePhonecat 9 жыл бұрын
+fredintheshed1 I will give that a try thanks. I had the car serviced recently just to count that out. However I didn't change the fuel filter.
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
+ThePhonecat A blocked fuel filter could cause the problem but you normally get fuel starvation under high load like pulling up a hill. Its a tough one without a stored code but I would think electrical first. best of luck.
@kabagameplay3689
@kabagameplay3689 8 жыл бұрын
has a light fine and flick between 2000 and 3000 rpm if the crankshaft sensor ? astra g 1.7 Diesel
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+Stefan Kabic They way to tell is to read the error codes stored and goggle them.
@melvinrichardson2864
@melvinrichardson2864 9 жыл бұрын
Very helpfull next time ill do it myself Garage charged £110
@jamescrawford2926
@jamescrawford2926 8 жыл бұрын
great video mate
@0xABADCAFE
@0xABADCAFE 6 жыл бұрын
Have you encountered an instance where the sensor is just impossible to pry out?
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
This one is was very tough. Of course the sensor is plastic and the block metal so it will always come out with force. You just need to be really careful that any broken parts do not fall inside the engine.
@chavsy85
@chavsy85 8 жыл бұрын
Is the sensor in the same place on a 1liter 12v petrol engine please be very grateful for your help.
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
If its the 3 cyl motor then its the same as the one in the video
@mahmoudelsaleh1218
@mahmoudelsaleh1218 2 жыл бұрын
And how about 1.2 16v petrol? Thank you
@DevDamian
@DevDamian 8 жыл бұрын
Thanks! Im going to try fix it this weekend.
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+Damian Balandowski Nice one, you will save loads of ££. Just let the exhaust cool and take your time. Esp removing the old sensor.
@DevDamian
@DevDamian 8 жыл бұрын
+fredintheshed1 Thanks for advice. I don't know if my corsa has same problem as on this video. But engine cuts off randomly, and tickles while driving, and I also have the engine light on dashboard, but when engine cuts-off / or engine starts tickling RPM goes to 0 and stays there ,but next morning it is just normal... Im going to try this sensor, If this won't help I will look for different solutions.
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+Damian Balandowski If you do not have one buy a OBD2 code reader from ebay, best £20 your ever spend. Get the fault code and google it. Someone else would have the same problem and fixed it mate. Best of luck.
@DevDamian
@DevDamian 8 жыл бұрын
+fredintheshed1 I even found some for 13 pounds, If changing this sensor won't help I will buy this reader. Thanks :)
@DevDamian
@DevDamian 8 жыл бұрын
+fredintheshed1 I did it today, lot of complications (getting sensor out, and screwing the bolt in), And also we did wihout ramps or anything high, just tyre + 3 thin woods pieces. But error did go out and car works better. I will drive more to test it, I hope it was the sensor.
@leetaylor3004
@leetaylor3004 8 жыл бұрын
hi is this just petrol engines or diesel also ? as I looked for mine on my 1.3cdti combo van
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
This was a 3cy petrol but a diesel should also have some form of crank sensor but not sure location.
@Ema_2726
@Ema_2726 5 жыл бұрын
hello has an acquaintance an opel Corsa 1.4 automatic gasoline from 2003 when the engine is cold starts when it is hot and it does not start until it cools down could anyone help me.
@CB-RADIO-UK
@CB-RADIO-UK 5 жыл бұрын
Attach a OBD2 scanner and look for error codes.
@RoofboxCamping
@RoofboxCamping 6 жыл бұрын
Very handy video
@lip03pd
@lip03pd 8 жыл бұрын
i have this fault on a 2004 meriva 1.7 cdti would it be in a similar position?
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+outdoorlip1 Its going to be somewhere around the bottom of the engine as that is where the crankshaft is located. The sensor will prob look very similar. Also rem that a camshaft sensor can give the same symptoms.
@CollosalTrollge
@CollosalTrollge 8 жыл бұрын
I have an Opel Corsa B 1999 1.6 Sedan. It was made in South Africa though, i think it would be very similar to the UK models , i think. Then again when i tried to follow a haynes manual my friend loaned me before the pictures were completely different which was irritating. So unless you are mechanic its hard to follow. If you are a Mechanic then the practice and stuff is very similar and it would be easier to follow and understand the theory and practical i guess. My luck i live here, i tell you. I want to get an odbc reader but i dont know which one to get. I think and believe i do have a odbd2 port.? I have been having a mysterious starting issue with my car for a long time and my mechanic says i should just ignore it. I dont like the fact that you are wearing out your starter and even though it is charged when u drive i believe the battery also gets killed. Please help with any idea if you have? I have also got posts of my scenario of my crank starting issues which might be of more help in describing my scenario. The crank sensor, i have heard of this also. My car battles to cold start. It is a mystery though because it battles to start 5-7 seconds when i leave work at night .... it starts with no accelerator but its a bad idle and then 30 seconds the idle starts getting better. (first crack scenario 1a) When i leave home though every morning, the car seems to "want to start" better ... you can hear it almost catching....if i can say that ....but then i let go of the ley and it doesnt start. (first crank scenario 1x) IF i had to do that though whilst pressing accelerator in a 2000 rpm position.... then it starts fist time. (following first crank scenario 1a)...after i have tried to start it and it fails to "catch", I now turn the key again and it tries to start but it takes like 5-7 second before it start and i seem to NEED to press accelerator also. I have had this issue say for the last 2-3 years, with i can solve it. I am not a mechanic and not really a DIY person but i have bought jack stands and a jack(jack seems to be useless though since it doesnt raise the car enough and my (tyres/tires) seem to still touch the ground). I am willing to learn theory and do some stuff on my car. I have cleaned my ICV using carb cleaner and even soap and water and leaving it to dry in the sun, I have even tried a new ICV and then i managed to get a proper throttle body spray cleaner. I have also changed my Air In take pipe and the Air sensor it comes with. I have tried 3 sensors. I have tried to play with the ICV by unplugging it from the harness and my car idles erratically so it means it work? I have also tried to take out my MAP sensor plug and my car idles erratically so i guess it means it also works. Yeh anything to try and fix this and understand this stuff, it seems that cars are simple and yet they are complex so i dont know. I guess almost like being married. LEt me know if you have ideas,, thanks.?
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
Intermittent faults are a nightmare so you have my sympathy. I was going to suggest the MAF sensor but you have covered that. You have a cam and crank sensor which can cause both issues. You need to get a obd reader. Also don't forget the key and imobiliser chip.
@CollosalTrollge
@CollosalTrollge 8 жыл бұрын
hmm not sure about key and the chip inside. When i used to service my car at the dealer before they once told me about my key and the chip inside nothing to do with a fault but they told me it was important. I dont think today i even know why. i mean my car is a 1999 car does it really matter , its surely old so i dont think we are talking abot technology like in the movie Gone In 60 Seconds,. I dont have an immobilizer. I will never buy one or even and alarm, im sure it just gives you head aches.
@CollosalTrollge
@CollosalTrollge 8 жыл бұрын
yeh so i one day unplugged my ICV while the car was idling or while i started it cant remember and i remember that the car didnt idle properly. Then i was experimenting and i tried the MAP sensor which on my car sits on the firewall in the middle of the car and it is connecting to the throttle body with one pipe. anyways i took it out and started the car , the car had erratic idling like high and then low and then high and then low....so i guess that part also works fine?
@CollosalTrollge
@CollosalTrollge 8 жыл бұрын
So then tell me, can you help me get the odbc scanner i need for my car please? i can also if you dont mind and if it okay with you ... you can maybe buy it for me and then send it to my work address in the UK ...i will pm u the details.... i can happily paypal u. A work colleague of mine is coming to South Africa in a few months time , he trying to sort out his visa which is why he is there now
@CollosalTrollge
@CollosalTrollge 8 жыл бұрын
I will probably have to send u video and pictures if you need so that you can see my odbc port and just have a general look at the car
@Nffc97
@Nffc97 6 жыл бұрын
Great video
@bradleighdavies4645
@bradleighdavies4645 9 жыл бұрын
I got a corsa standard engine but won't start should I do the same
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
+Bradleigh Davies Yes if you get the P0355 error code. There is also a sensor on the camshaft which also fails but is much easier to get to.
@kidger3703
@kidger3703 8 жыл бұрын
hi there does anybody know if this is the same sensor on the zafira 51 plate. and is it in the same place Fred in the shed?
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+Kieron Carberry Sorry mate I do not know. The location of the crank sender will be located at the bottom of the block.
@Mr-nt8mz
@Mr-nt8mz 6 жыл бұрын
Hi there thanks for this video, can you tell me where you got your odb reader? I'd like one that convenient. I have one but always need pair it with a cellphone and using a specific app. Thanks in advance
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Just picked it up off Ebay. Think it was about £25. Not the last word in build quality but seems to work ok.
@Mr-nt8mz
@Mr-nt8mz 6 жыл бұрын
fredintheshed1 thanks ;) i appreciate your quick reply
@richardd9867
@richardd9867 7 жыл бұрын
Top Man! Cheers bud
@grahamewilliams6642
@grahamewilliams6642 5 жыл бұрын
Would solve the problem but sensor being a stubborn thing and refusing to come out!! Even after lubricating it!!!!
@CB-RADIO-UK
@CB-RADIO-UK 5 жыл бұрын
Yes they are tough. You have to be careful not to snap it.
@grahamewilliams6642
@grahamewilliams6642 5 жыл бұрын
@@CB-RADIO-UK Had to admit defeat and call RAC lol, and as he was here he done full diagnostic check for me, bur thanks again for the video, it still saved me a lot in mechanics fees
@kidger3703
@kidger3703 8 жыл бұрын
many thanks +fredintheshed I've found it and ordered it so be fitting that along with a new cv gaiter😀 it was by the oil filter
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
+Kieron Carberry Nice one. Just take your time wiggling the old one out as you don't want any bits to fall inside the block. Best of luck mate.
@constantincretu9564
@constantincretu9564 3 жыл бұрын
Pozitia cum pot să îl inlocuiesc
@constantincretu9564
@constantincretu9564 3 жыл бұрын
În românia vreau tradus
@shtex89
@shtex89 9 жыл бұрын
is this 1.7 DTI Isuzu engine ????
@CB-RADIO-UK
@CB-RADIO-UK 9 жыл бұрын
+Stefan Nikolic No its the 1.0 3cyl petrol
@gripen21
@gripen21 8 жыл бұрын
Hi, your video is exellant, thanks...
@CB-RADIO-UK
@CB-RADIO-UK 8 жыл бұрын
Glad it helped.
@tonyn9858
@tonyn9858 8 жыл бұрын
good video thank you
@dherdy9205
@dherdy9205 7 ай бұрын
Cheers Fred
@justicelebopo9036
@justicelebopo9036 7 жыл бұрын
we put crank sensor still not start
@CB-RADIO-UK
@CB-RADIO-UK 7 жыл бұрын
Re-check the fault code. A faulty cam shaft sensor gives pretty much the same non start results.
@lzh2382
@lzh2382 6 жыл бұрын
save ur £300 great job
@teaCupkk
@teaCupkk 7 жыл бұрын
A word of warning: if you get that code, DO NOT CLEAR IT before you change the sensor, or your engine won't start at all. Most other codes you can clear to see if they show up again, but not this one.
@westmids98ez35
@westmids98ez35 2 жыл бұрын
What should you do if you’ve already reset the code after identifying the fault
@teaCupkk
@teaCupkk 2 жыл бұрын
I could find no solution, the ECU/engine refused to budge. Had to transport the car to an Opel service, where they magicked it back to life - it wasn't a large bill fortunately, but i don't know what the repair entailed, i didn't ask. Sorry i couldn't be of more help.
@burinhosapataias
@burinhosapataias 9 жыл бұрын
good ideia thanks
@bart278
@bart278 6 жыл бұрын
Great video !! On my corsa b 1.2 is very difficult to remove He When i probe to move He only rotate but dont want exit ... Little bastard 😑😅
@AWWWWWWWWWWWWWWWWize
@AWWWWWWWWWWWWWWWWize 7 жыл бұрын
thanks
@stephharrison6138
@stephharrison6138 8 жыл бұрын
top video 👍
@vasily9864
@vasily9864 7 жыл бұрын
The fault code is P0335 you accidentaly typed it wrong please re-type the tiltle of the video for no misconceptions!
@CB-RADIO-UK
@CB-RADIO-UK 7 жыл бұрын
Thanks for that. Did not notice. Amended.
@vasily9864
@vasily9864 7 жыл бұрын
you re welcome, no worries!
@evsenmedyahaber1422
@evsenmedyahaber1422 7 ай бұрын
👍👏👏👏👋
@fdyjt
@fdyjt 6 жыл бұрын
WTFF here in belgium opel asked me 500 EURO's to replace that thing on my opel astra h
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Wow 500 jeez.
@pollyheenan4283
@pollyheenan4283 6 жыл бұрын
@fredintheshed1 I live in somersert I'm going to attempt to do it my self😁as i just brought the part for 21.50 and I'm kinda broke 90 is a lot considering I could do it for free 😁
@CB-RADIO-UK
@CB-RADIO-UK 6 жыл бұрын
Just take your time. The hard part is prising the sensor from the crank case. Just dont force it as the last thing you want is the sensor to snap or parts to drop inside the engine sump.
@johncollins8304
@johncollins8304 Жыл бұрын
I CANNOT undo the bolt. Bought a set of torx but couldn't get it to go on square. There is something stopping it. Tried 8mm spanner. N.G. Tried long thin grips. N.G. Thinking the pigtail is blocking it, i tried uncliping but working blind. You removed the bolt with the clip in place... Ideas please!
@CB-RADIO-UK
@CB-RADIO-UK Жыл бұрын
I dont rem my bolt being too bad. Prising it out was tough though. Maybe some extra long spanners might help put more torque on the bolt. www.ebay.co.uk/itm/165737722746?hash=item2696bcf37a:g:sKcAAOSwd7tjU-5p&amdata=enc%3AAQAIAAAA8P40SWZis7mQHM%2FmLlCstHBe1GMu77zLWAfMlmiKj7BUOnI4n41A965o2nNxP1VgBeg2DamBFyEU%2FdjpEHRaasWue5dGsRP%2FvTlU0nelcYKKwtWmPbvSk45OourYsEa98mgo3wzYKabStC5BlR%2BeV2fuYrbLfhTZEqwgV5sz7ZTlXaKv7BYeugPAiTXqHmVNqL%2FHS9gPSZ4KUwwxaSqYmAF0tCay11REOcE1JbVdDD6jHllQ9k75DnwDp8eaT35nOGRg0GYJvtv8%2BSrFAESeP3hGc9pm0741Sd7mr%2Fp8cAgnB5buY%2BliiMRyHo8VjxWv7g%3D%3D%7Ctkp%3ABk9SR5T85YafYg
@johncollins8304
@johncollins8304 Жыл бұрын
@@CB-RADIO-UK Thank you for replying, and so quickly. I've had a look at the link which I'll bear in mind for the future. I wonder who has used them for what. In fact it's not leverage that's the problem, rather that I couldn't get anything to fit down over the head. But, I went and looked for another 8mm ring, and I think the ring was thinner. Anyway, it went over and fit with a little pressure and the bolt came free. Equally nice, with a long thin electronics screwdriver I got a foothold then pushed in a broad cup (??) car upholstery tool and it just levered up. (I say all this in case it helps s.o. else.) Thanks again.
Crankshaft Position Sensor Test
4:21
ScrewsNutsAndBolts
Рет қаралды 529 М.
Vauxhall Corsa 1.2 crank position sensor replacement
4:48
MTM Motor Services
Рет қаралды 1,9 М.
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 30 МЛН
Quando eu quero Sushi (sem desperdiçar) 🍣
00:26
Los Wagners
Рет қаралды 15 МЛН
Beat Ronaldo, Win $1,000,000
22:45
MrBeast
Рет қаралды 158 МЛН
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
9 Bad Crank Position Sensor Symptoms (FIX It in 9 Minutes)
9:28
Car Care Clues
Рет қаралды 65 М.
Curatare EGR Corsa C -- Z12XE EGR cleaning
21:48
OP-TIM Auto
Рет қаралды 88 М.
Vauxhall Corsa D Crankshaft Sensor Replacement Fault Code P0335
11:45
Opel Corsa C 2004 door panel removal
6:20
GR
Рет қаралды 139 М.
Vauxhall Opel Corsa C - How to Remove and Replace Crankshaft Sensor
6:27
Bigger Engine.
2:03:51
SimonFordman
Рет қаралды 279 М.
All Fuses & Relays from 2003 Opel Corsa C How to Use / Test them
15:00
Opel Corsa C PUMPA GORIVA / Fuel pump
7:18
MN Rujiska
Рет қаралды 1,4 МЛН
Vauxhall Corsa D Crank Sensor Replacement - Fast Fix Friday!
10:01
Papa 77s Garage
Рет қаралды 83 М.
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 30 МЛН