Overheating After Replacing Radiator, Pump, Thermostat? Burp Coolant to Remove Air Pockets!

For More Info visit us at: 1aau.to/h/cBL/
So you just replaced something to fix your overheating cooling system, or maybe you flushed the coolant, and now it's still overheating! Sometimes, air pockets can form in the engine or hoses, which hurts the cooling capacity of the vehicle! In this video, Andy gives you some tips on how to remove air pockets from your car or truck's cooling system to ensure it runs at just the right temperature all the time!
Check out this playlist for more great tips from Andy and the other 1A Auto mechanics!
• Tips & Secrets only Me...
For More Info visit us at 1aau.to/h/cBL/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@matthewbrown5371]

I nearly didn't do this while replacing my radiator. My dad happened to call and ask how things were going when he asked if I burped the system. I had no idea what he was talking about and had to look it up. Thank God I did!

[@markwittels1337]

Great video thanks. Love the fact that you don't have loud obnoxious music in the background. Camera work, lighting and editing is on the money !

[@generalralph6291]

I was so upset I thought I blew a gasket after replacing the pump. Glad to learn all this!

[@BadDecisionsJeep]

Only video on KZbin that actually shows all the different ways to do this! Thank you

[@michaelsaywhat6980]

I've watched at least 10 different coolant change or flush videos to find the common steps between each video and I learn something new from each video. The thermostats needs to be installed on with hole at the top for the air to flow through was something I wouldn't have catch. Thank you so much!!

[@AllAmericanDreamChaser]

This guy is great! Thanks for showing how to vacuum a coolant system. I haven't seen it done like that before! These videos just keep getting better! Thank you!😀👍

[@waltercastro2015]

I have air compressor shoooooooot. I choose this method even if the vehicle is easy to burp. I feel this is the easiest way and most accurate. Free minded. Gonna get on the isle create a vacuum asap.

[@RamboRichardson]

1A Auto is the best! These videos are so helpful! I can't even tell you how many repairs I have done using 1A Auto videos, but I just got done changing the water pump, serpentine belt, and pulleys. Thank you!

[@randyfields8595]

You guys @AA do good videos keep up the good work 😊 thanks.

[@celiavann4336]

Very well explained, a lot of other demonstrations miss a lot of steps that you covered

[@colleenhatton4333]

I was just working on the system. The fluid in the overflow still boils after a water pump and thermostat replacement. Love this channel!!!!

[@bradmironik6137]

Thanks for showing how to use the vacuum tool. I bought one for my vw 2.5 jetta since my setup just has the reservoir tank.

[@garymcmullin2292]

that was a very well rounded treatment of the subject, covered all the possible situations and solutions, thank you! Some vehicles have the heater core at the highest point in the system and those can prove a little stubborn in ridding air lock. However that is usually achieved with repeated heat up and cool down with circulating coolant. Just be sure to have plenty of reservoir coolant available in the expansion bottle so that as the air is purged there is enough coolant to fill the void.

[@TheSloansFour]

I had to replace the radiator and purge. Now my gauge barely gets past warm. So you think if I just do the purge process a few times it could relieve a block at the heater core?

[@miguelmendoza4626]

Loved your video. Spoke very clearly, very precise and descriptive. Anyone will be able to follow along.

[@brentkoster7250]

I really liked this explanation of bleeding the coolant system, especially the part of placing the little hole in the thermostat at the top which promotes air escaping. You guys cover all the issues. I will be watching many more of your videos. Thanks.

[@marknasia5293]

Lots of great tips that a DIYer would miss, this channel is golden for helping DIYers do a 100% job. Thanks 🙏 it helped me out.

[@cujoedaman]

It's neat because they have a store on eBay that I occasionally buy from too :D

[@turnipsucks6416]

Wow. Far more information than I expected in this video. All of it valuable. Thank you!

[@antouab221]

Awesome video, so educational and thorough. One of my favorite channels :)

[@richardzapor1983]

Excellent video ! have been struggling with my '78 chevy step van seeming to overheat for a few days .Finally concluded the problem was the gauge . But anyway this question of burping the system was part of the equation so this is vey helpful .

[@goodmourningamerica5151]

Thanks for this video..changed out my radiator first and it still was overheating after I filled it up .so I thought well must be the water pump and got another thermostat as well. Changed that and still was overheating..well guess what....I didn't let the air out. Great info and helped a lot..your guys video help me save around 2000 in labor btw..dodge ram 1500 2011..god bless you guys

[@1AAuto]

+Good Mourning America Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@mikefixac]

Thank you for this. I changed my coolant on a Honda and didn't know about what you're talking about in this video. It led to ruining the auto transmission.

[@ninaje1909]

I literally just went thru the intro of this I'm thinking what did I do wrong my car is such a premadona this helped me feel not as dumb I gotta burp my brat of a car thanks you guys rock 😘

[@TexRobNC]

I'm just coming to upvote and comment for visibility anytime I see a video for this. I had been chasing an issue in my 2011 WRX, and it turned out to just be that boxers, and those with a TMIC in particular, have to be burped a specific way. So, yes, air can cripple your car and make you think you have a major issue. I must have just had air at the water pump or something, because I could not get any circulation, even after replacing my thermostat. Proper burp, fine.

[@JohnS-ps9jv]

Thanks for the tips. You're video was helpful when I replaced my friends thermostat that I purchased from 1A Auto!

[@rustyhampton2020]

I’m thankful this video appeared in my app. It’s what I needed to finish changing my thermostat. Very well produced.

[@lalaalaaalaaaalalaa]

You know these inside out and explanation and instructions are Golden! Thank you!

[@lewiskalinde6073]

I really appreciate that , how to balance the coolant level . Great video . Please keep up with more videos , they are my college courses . Stay safe even if I am God ! Much love 🤩 .

[@gordonenquist36]

Thank you for the info. much appreciated. I think more words about the radiator cap and how it relates to the whole system would help us weekend mechanics. Cheers.

[@diane-mn8ou]

Very good explanation your well spoken clear easy to understand good visual always sho and tell the best on 1-10 it's a 15 thankyou I'm s73 worked on car since I was 10 you showed things that I knew also showed things I ve seen like the vacuum but never seen used prior people like are very knowledgable helpful and a good citizen keep up good work thank you

[@Coyote5555]

those intros are well thought out... i appreciate the effort!! great content

[@ironfistarrival]

You Wellcome !

[@Retroman2000]

They should do more like that

[@1AAuto]

+Retroman2000 Thanks for the feedback!

[@1AAuto]

+Coyote Thanks for the feedback!

[@shinola228]

The funnel he's using cost around $30. I bought a simpler one at Walmart for $3. It's just a regular funnel but with a wider outlet. It fits snuggly into most radiators, and if it's loose you can just wrap it a little with duct tape. Works real well for this job.

[@seanotoole23]

Thank you for a straightforward answer very helpful

[@americansamiam]

Thanks for the video. Everything was explained well and covered many different scenarios. Appreciate the attention to detail. MY 2018 Expedition was getting hot after I replaced the heater hoses. Tried the parking on a slant and allowed the air pockets to remove.. I also made sure to turn on the heater inside the car when I started after burping just to make sure things were flowing well. Everything is back to normal..

[@1AAuto]

+@americansamiam Thanks for the feedback!

[@sistercalhoun4444]

Thank You Bro I like how you Always Explain things and show your how too especially diagnostics most common problems with vehicle and how to replace part step by step like Chrisfix!

[@PrometheusGroup777]

Absolutely great tips and content! I have an 06 grand prix.

[@DashCamSerbia]

You and Lenn are the best!

[@Matt-cd9mo]

Thank you ! I appreachate the tip reguarding the goes on top when reinstalling to help bleed out the remaining air. Very nice !

[@Matt-cd9mo]

The whole goes on top

[@leonciorodriguezaguilera9513]

Very Helpful Video Tutorial Amigo!! Thanks a Lot For Sharing!!

[@kiosoyoufer]

Good information thanks for sharing those tips 👍

[@user-bw1gx8sx1o]

I must say my anger really gets the the best of me. Especially when it comes to working on my engine... not having all the right tools or ideas. But watching A1auto really really love these guys must subscribe And apologies once again for my inconvenience

[@1AAuto]

+b Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@mightywalrus6414]

Dude i be goin berserk too!! BERSERK!!!

[@ClintonSnow]

Excellent video, well explain, they show all the right tools it's 100% helpful video. Please do more videos like this one.

[@j.b.4340]

Years ago, my buddy put a new radiator in his 2000 Dodge Ram. An air pocket cost him a $4500 engine. That catastrophe made me gun-shy. This video makes me confident. Thank you.

[@artsmith103]

After new radiator, hoses, thermostat, etc. you just have to be really careful the engine is cooling. Then make sure heat is working. In not too hot weather, I like to drive with heat on low and window open. If the heat quits you'll soon have an overheating engine due to inadequate fluid flow. Likely from a leak.

[@mistydawnwilson6200]

super helpful and still have a question, if it still overheats after you burp, what do i look for next? is it a water pump issue? sensor, if i have one?

[@robertdiehl9003]

This guy is funny & knowledgeable..

[@kenlogan2789]

I am glad that I watched this video. It shows how engineers always add a wrinkle to keep DIY guys off balance. This is a "MUST SEE" video for us car guys. Thumbs up.

[@Lucy00682]

And gals.

[@johnstocker6728]

What I do on my wife's linking is parked the car and a little bit of a downhill angle. That way the air is forced to the top. Worked for me

[@brad2548]

Awesome information. Thank you

[@cioch84]

Great video! I’m kinda car stupid and you made this very easy to understand!

[@barrellcooper6490]

50/50 mix is needed for -34F Freezing point. 33/67. It's rated to 0. Which means you still won't do damage until you get well below 0F. I live where there's almost never below 0F. I've been buying 1 gallon of antifreeze and 2 gallons of distilled water. Mixing it to get 3 gallons of 33/67 mix. I've used this for 2 decades. Never a problem. Antifreeze jugs used to have a mixture chart.

[@ByGraceThroughFaith777]

That cateye chevy looks pristine 🔥

[@blackpowderfirearmenthusia3194]

Thank you, I'm going to try to burp the air out. I replaced the water pump and now it over heats. I think it's air. I never heard of this until watching this video, thank you.

[@static_Tricolor_camry]

My 97 Accord EX started to overheat when I was waiting to make a Left turn to go inside the mall parking lot, I saw smoke coming out of my hood I looked at the temperature gauge and it was maxed out all the way to the top Red line Hot. I quickly pulled over, parked my car shut the engine off looked underneath my car there was radiator fluid leaking out like a water tap. I had to call my buddy to bring me some radiator fluid and water. It turned out to be a slow leak, I still managed to drive it back home and to work the next day while monitoring the temperature gauge. As I'm halfway through my work shift fluid starts leaking out, I had a bottle of radiator fluid in my car to top up after work I got down to figuring out where the leak was coming from sure enough it was the heater core hose a tight spot to reach. There was a small pin hole inside the hose causing the fluid to leak out, after replacing the hose and topping up on radiator fluid and water it stopped leaking and the temperature gauge is where it should be at Normal.

[@ivanhernandez4461]

Thanks for this info.. I'm on my way to check what you've mentioned. Thank you

[@fortunatedad7695]

This is such a great video. I just replaced my thermostat and changed the coolant. I was wondering why my 2012 navigator was only running at 184 degrees. Installed an OEM part. Any ideas? Thanks

[@mixedboi]

Very well explained sir. Nice!!

[@robertchase6199]

Man I'm glad I found this video . I thought my new water pump wasn't working or something worse.

[@briany3002]

This guy is definitely my favorite

[@ironfistarrival]

Brian Young ! Are you really a Young man !?

[@6thinkforyourself9]

Omg! I'll try this right away! And then I'll update my comment 😅. I had my radiator repaired and after that the temperature rises at high speeds. I'm using the vehicle without thermostat since then. I've tried to install the thermostat but the temperature issue returns. I'll try to purge the air out.. If it doesn't solve the problem I think there might be something clogged in the system. (Hot a/c is not working either)

[@richardpenland3506]

Excellent job! I appreciate you showing many different ways to 'burp' a cooling system.

[@1AAuto]

+Richard Penland Thanks for the feedback!

[@meagain8403]

After all your helpful videos...the least i can do is subscribe

[@unclebuckii6074]

Thank you for making this video. It has helped me.

[@keithnoneya]

Loved it. Cool tools I've never seen before. Thanks for sharing. Best Wishes & Blessings. Keith Noneya

[@midnightraiin4035]

i changed my own timing belt because of this guy, on a 2000 Nissan Xterra. you were a big help Andy!

[@gentlemansbusa2985]

I absolutely love the vacuum way it makes it a breeze!

[@djrocweilerrocweiler4136]

Replace thermostat radiator still with running hot looked at your video.. Respect

[@Catman1798]

You have videos about transmission oil changes? For those sealed transmissions

[@chuckvoss9344]

Did not know about the vacuum system. Thanks

[@flyingcat2054]

I so wish I took auto mechanics in high school. At least I would be familiar. I’m such a noob with cars.

[@Wayne-Jones]

Great video, thanks 👍 I think my car is suffering from an air lock even after running the car with a expansion funnel, still having heater just warm at idle but hot with fast idle. Just can’t seem to shift it. Few more ideas for me there, thanks👍

[@jimjam36695]

You solve this? Same issue.

[@irisbaez1972]

I use that funnel every time and it goes perfectly.

[@sollykhan2385]

Great Video, Thank you for the time and effort, that 'Burping tool' looks good, where can i get that from? please post more good content too, 🙂

[@keitharmstrong263]

That was a good well explained education on removing air out of a radiator system in under 10 min. A BIG thanks to 👉 U....

[@lancemorris9581]

It’s Just Crazy I Know By Difficult U Was Talking About The 1500’s System Yess Getting The Air Out Of Them Without That Vacuum Is Like WW2. Thank You.

[@SHAKEnBAKElvl9000]

Thank you, just refilled coolant on a empty 07 avalaon and it kept boiling all thr coolant and spitting it out. Fkund the bleeder screw hidden in back with no space. Going to buy the burp kit u showed, hopefully it works

[@arainadiaz9219]

Excellent advise. Thanks

[@condor5635]

Awesome video. Love that syringe! Perfect size! Where can you get one like that

[@khanzada4043]

That smoke looked so artificial. Good job on the video. Thank you so much for teaching us.

[@1AAuto]

+Khan Zada Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@findit6333]

It's steam, not smoke.

[@njoeandjen]

All your Videos Rock Your Awesome keep up the Excellent work ever need help would love to work with your company Thanks!

[@Shagdawg]

Bro you help me so much!! Thank you!!

[@sendit1158]

A1 videos = Top Notch

[@1AAuto]

+80s DIRTBIKE Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@blairguinea6811]

Great job Sir

[@charmanderkid1500]

Where can i get that air fitting that attaches to the reservoir that you used? Also how much pressure do you bring it up to? I had to watch on low volume so if you said i missed it

[@GTAW8]

Thanks for the video!

[@mrfalcon135]

thank you very much!!!

[@morsgie]

Make more videos, love DIY for my cars

[@cuttingedgecool7235]

Very good information!

[@kevinhancock4064]

Great video . Can you help ? Hg replaced months ago ..therm and coolant sensor replaced under a year ago. Rad almost 2 years ago ..New cap recently. Dash lot up while ago coolant temp high gear down. Thrn gear down again . Coolamt came from overflow over anyone I let ot cool and I wasn't far from home so mostly coasted it home . Until I topped it to take to garage ..didn't need much of a top . Garage done all tests and all os ok . Mentioned at a guess at possible causes of egr cooler etc but big gamble etc

[@cujoedaman]

Oh, look, a Silverado missing push pins on the radiator beauty cover :D A lot of the mid 90's to early 2000's GM 3100's and 3400's had a bleeder valve on a pipe that ran just above the front tappet cover. If you were lucky, the valve wouldn't be seized and break off when you tried to open it to bleed the air out. Good times.

[@CLASSICS200]

Another tric you can try is to turn the air-conditionig on and your radiator cooling fans should come on automatically and stay on to keep the car from overheating until you get the car home and to the mechanic

[@ElIngLopez]

Nice. Thanks much. Ayuda aplastar las mangueras con las manos para sacar el aire?

[@Sonja7218]

Thanks!

[@beersoflegends]

A 1 auto NEED MORE LIKES !!!

[@2121heatherh]

Could I have caused the leaking out of coolant by not bleeding air after filling up coolant to near empty reservoir?

[@a2002zx2driver]

I have a 2012 Ford Taurus 3.5l and I just changed the fluid to put all clean antifreeze in it, and I have used everything shown here, still has air in there somewhere. I did a pressure test to see if it has a hole anywhere in the system and it held 25lbs of vacuum for 30 minutes so no leaks in the system and I did a compression test and it’s still fine so I don’t like the fan staying on at almost full blast and I know it’s not the fan or anything to do with it I have all new and I tested it in my wife’s Taurus and it did it’s job perfectly. Am I going to have to continually open the pressurized overflow cap to release air from the overflow until it’s out?

[@rickanderson3612]

Can you tell me how to drain and bleed and burp my car's coolant system? I have a 2005 Impala 3.4 L. It has a radiator cap, reservoir/expansion tank, a bleed valve above the water pump, and a bleed valve on top of the thermostat housing. I followed the intructions in the manual. I only got 4 quarts out when it has almost 12. When I tried to refill it, I turn on the car and heat like the manual says but coolant comes out of the radiator way before it gets hot, so I put the cap back on.

[@brianwagner7295]

I have a 2014 Chevy Cruze and my coolant boils in the expansion tank, I am still getting hot air in the cab. I just replaced the water pump with a timing belt change and I also replaced the thermostat as well. If you have any thought let me know.

[@johngjacobi]

Thank you so much

[@markkouros6628]

When you mentioned the little hole in thermostat face it at the top .. does that mean towards the firewall or around the other way towards the radiator the front of a car thank you....

[@benjaminmeza5372]

Hi, could i just run the engine for about 10 min. with radiator cap off to burp the air out??

[@aleksandervalentine5619]

Great job explaining it, thank you 🙏🏼

[@ianpaul6931]

Great video, thanks

[@heathcalvert1319]

What's the best color antifreeze for a dodge 5.9 360 some say the Orange

[@carlosjackson4474]

Great video, what's the item number for that air lift system, I'd like to purchase it from 1AA