Following this vid, I very easily changed the sensor myself, on my gf's 2017 Jeep Wrangler Sport, no doubt saving her like $300. Thank you!
@celiracer942 жыл бұрын
Hey there, Great vid but one parts of miss information at the 6:00ish mark you reference the "expensive rivets" but they are actually clips and come yes once ruined will need to be replaced, but can easily be removed properly and re-used. Just get a small pick to poke around center pin and lift it out to where you can pull it with needle nose pliers. Once lifted up and out can easily be pryed on and removed . Hope this helps someone
@marioguzman5676 Жыл бұрын
Yes
@marioguzman5676 Жыл бұрын
Thanks
@saltytexasranger6301 Жыл бұрын
If you don't have an OBDII scanner, Jeep JKs will give you the engine code on the dashboard. All you do is insert the key into the ignition and turn the ignition to the "on" position 3 times in a row...
@tlspangler8423 Жыл бұрын
This is the best video I've seen on replacing the Engine Cooling Temperature Sensor! THANK YOU for posting. My local garage (not a Jeep dealer) misdiagnosed my problem and wanted $1225 to replace the thermostat housing!! Crazy. They actually said oh we are going to replace the thermostat and housing that is why it is so expensive .... um excuse me but it only comes as an assembly so yea of course you are replacing that $40 part. Once I told them I had already replaced the thermostat (I did it for ~$50) they decided it would be $885 to replace this ECT sensor! No thank you. After seeing this video I will do it myself. The garage didn't actually do any troubleshooting other than read the code then blindly suggest thermostat replacement, very frustrating. I won't be going back to that garage.
@PhotomikesGarage Жыл бұрын
Glad I could help.
@whitebreadcantjump Жыл бұрын
Stumbled upon this vid that deals with my exact error code. Kind of sucks you have to take the inner fender off. Would have been nice to be able to get at it from under the hood. Nice troubleshooting and explanation of your troubleshooting results. Did the same thing for my jeep, gets killer heat and engine temp is good. Looks like I'll be doing this same fix. I have a 2014 Jeep Wrangler Sahara. Might be able to use your exact part numbers. Thanks for posting this vid.
@michaelpeterson11692 жыл бұрын
Videos like yours have saved me literally thousands of dollars. Thank you for sharing!
@sherifx51222 жыл бұрын
Thought you are not supposed to use any sealant if it has a crush sleeve.
@tomtravis30772 жыл бұрын
I live in a rental and don't wven have a driveway. The neighborhood is mostly homeowners so working on cars on the street draws frowns. So I was using a local garage for basic maintenance and repairs. They tried to charge me 800 bucks to do this. Looks like the neighbors are going to frown a little today.
@justinwittmer92932 жыл бұрын
How much have you driven it since replacing the sensor? Did it solve the P0128 code? Or still have to replace thermostat. I should have done sensor first because my temp read fine on my gauge too but I chose to change the thermostat. Seemed easy. There’s two bolts, top one came out like butter but bottom one snapped. Was tough to extract but I got it after taking the crossover housing out. I have to wait another 12 hours for gasket maker to cure before I can refill it with fluid and see if it fixed it or if I have to do sensor. Just curious if that fixed your problem.
@JCinHawaii2 жыл бұрын
No, he has another video out where he changes the thermostat & housing and mentions that this didn't solve it
@tonym97719 ай бұрын
Couldn't you also pop the steering shaft off to access this as well? Seems like there's a good gap there that would only take a bolt or two in order to be able to access? EDIT: I did exactly this to access mine. A bit tighter, but doable with the right tools and only requires removing one bolt from the lower steering shaft, to pull it off
@LWRC11 ай бұрын
Just FYI on the teflon thread tape - you applied it backwards on to the coolant temperature sensor. The direction of the tape should always go on so when you thread the sensor in, the tape will not unwind!
@rjlinnovations15163 ай бұрын
Thank you so much for sharing your very informative video tutorials 🙏. Sending my full support. Have a great day
@PhotomikesGarage3 ай бұрын
Thank you!
@foroneanotherwinningtogeth1142 Жыл бұрын
May I ask a silly question? Is this the same one that is on the oil cooler unit or something different? I just replaced my cooler and now have a sensor error. Trying to avoid opening up my whole engine bay again. Thank you!
@xuantrungnguyen319 Жыл бұрын
Me same question too At engine oil coolant has temperature sensor too😂
@eddaeges93092 жыл бұрын
Great video. I have the exact same symptoms. I will. try this first. Again, thank you for the video.
@Smokeyfilms_ Жыл бұрын
It will tell you the engine code if u turn ignition on, then off and on 3 times quickly while pushing in key in ignition.
@CHER19439 күн бұрын
How long can I drive with that engine light on my heat is fine. It’s obviously what you stated in your video faulty coolant temperature sensor.
@istinkatgolfКүн бұрын
Should we be concerned that right after you use the knife to open the package, the newspaper story shown says "Fire at site of previous stabbing"? 🤣
@m0jav3gr33n2 жыл бұрын
Help! I replaced the thermostat first (thinking it was that) and the code went away from the dash but remained on the code reader as a permanent code. Coolant temp at 218 degrees (normal), and gauge read at mid-range but still no heat. Would it be the sensor or something else?
@timhart89472 жыл бұрын
I found that pulling the fender off works for me. They did put it in a tuff spot.
@dangarcia6709 Жыл бұрын
I replaced it in 10 minutes without removing the fender. Used some zip ties to hold the inner fender up
@KISSHOOTERS696928 күн бұрын
The Jeep dealership in my town wanted $25.00 ea for a plastic push pin. Bought a box of 25 from amazon for under $8.99.
@ThomasShueАй бұрын
The plastic $8 each rivets, you press in the center and they pop out
@tdz692 жыл бұрын
Check for leaks after the repair AND AFTER you’ve driven it.
@joeytomato Жыл бұрын
DO NOT USE THREAD TAPE on this part... Ever.
@Jbainbridge59 ай бұрын
It's almost like it's a brass fitting for a better ground or somethin. And B, don't ever put teflon tape on brass because you don't need to...
@SoloHiker13 ай бұрын
I don't understand why he did it when the one that he removed did not have tape on it.
@kodyrobbins9118 ай бұрын
So I just did this repair and the connector won’t fully lock on to the new sensor it’ll click and lock on but if I give it a decent tug/pull it’ll pop off. And I’m still getting the check engine light
@davidwatson2229 Жыл бұрын
those riffets u were talkin about that u say u messed up. u take a small screwdriver pop out the center button then pry it off the whole thing wit trim tool
@henrybucki78136 ай бұрын
4.24 teflon tape is put on in the same direction as you put on the fitting CW direction
@jimhudacko60152 ай бұрын
No to be used on crush washer applications
@aaronanthony13632 жыл бұрын
So glad this isn't on the oil cooler, I was like please...
@regularguyfixes314211 ай бұрын
So I’ve got the temp sensor code but my temperature gauge is reading correctly…. Not sure what that means if the sensor is still bad or not…
@cali52159 ай бұрын
Thanks for the video. Great help.
@elguapo77222 жыл бұрын
I have aftermarket fenders and liners. Huge pain to remove. Is it really too hard to go in from the top? Is this the 3.6? Mines s 3.8.
@jeffhendrickson8839 Жыл бұрын
I just removed the steering shaft and took about 15 min. Don't have to drop the inner fender
@tbday3322 Жыл бұрын
Just did one at work dropping steering shaft one bolt and easy peazy 15 min all done
@Vin_easel11 ай бұрын
@@tbday3322can you explain this further? I was looking at it and it seemed that this would be the way to go, but I don’t know anything about the steering shaft. Is there tension on it? Can I damage something by removing that bolt? Or is it as easy as remove the bolt and then put it back after and re attach the bolt?
@tbday332211 ай бұрын
@Vin_easel there is just a jam bolt thru the upper part under the brake booster . The shaft is indexed so comes off one way and goes back only one way. Pull the bolt out all the way then the shaft should wiggle down . Once it is you will have plenty of room to get your hand down to tge sensor to unscrew it. Leave the radiator cap on tight you will only loose a cup or 2 of coolant
@Vin_easel11 ай бұрын
@@tbday3322 thank you for the info. In a separate forum, someone suggested I should disconnect the battery so the air bag doesn’t go off? Is that accurate? And does the shaft easily go back into the indexed part, or is there a lot of tension? Do I need any special tools to get it back in place? Thank you for your help
@tbday332211 ай бұрын
@Vin_easel disconnecting battery is never a bad idea . I didn't only had to wiggle the shaft by hand slipped right down . It should slide fairly easily it's designed to collapse in a crash. Turn the wheel till you can access the bolt then lock the steering wheel with the key nothing should move .
@julianbettini52902 жыл бұрын
hey there, did you have any more water leaking issues after the fix that you posted almost 2 years ago?
@PhotomikesGarage2 жыл бұрын
Not really but you have to replace the weather strips every once in a while because they deteriorate.
@heartofthunder1440 Жыл бұрын
I’ve watched plenty of these types of videos, the disconnection of these sensors are the most problematic, and I would say 2-3 out of every connected sensor goes smoothly. Unless if your working on brand new vehicles, I don’t care who you are, disconnecting these sensors aren’t as easy as they normally show in these videos.
@commandowolf94632 жыл бұрын
I saw your car in new west minister we searched up your channel on the window
@kenyadodd90999 ай бұрын
Thank you so much
@salyoungkid Жыл бұрын
Did you have to burp the system after? Or no need
@dangarcia6709 Жыл бұрын
No
@sole_valley3032 жыл бұрын
mine is not on the side ??? Is it behind the oil cooler I seen sometime like that wen I change the oil cooler
@jondunn1980 Жыл бұрын
Thanks for the video!
@G_RAThbun Жыл бұрын
I have searched everywhere on the internet and cannot find that code reader that you're talking about torque Lite, could you give me a link for more information so I can find it
@PhotomikesGarage Жыл бұрын
It is an app available on Google play store.
@G_RAThbun Жыл бұрын
@@PhotomikesGarage I'm looking for the device the app I can find. Tell me where you got your device?
@PhotomikesGarage Жыл бұрын
@@G_RAThbun I actually use this ebay.us/ozVJVR Its cheap and works most of the time.
@jasonparente65856 ай бұрын
Thanks!
@johnvick6855 Жыл бұрын
Is that the 3.6 engine? Is the temperature sensor in the same location as a 3.8?
@mingcong1345 Жыл бұрын
In some engines the sensor is on top front of the engine block. Making it so easy to replace. My 2011 Jku sport is like that.
@Ray526 Жыл бұрын
What is the torque specifications for that sensor?
@WwEN1GM4wW2 жыл бұрын
Thanks man!
@wykkydjvc Жыл бұрын
at 4:20 sound goes off be nice to see a view of the spot from the top
@dangarcia6709 Жыл бұрын
I was able to replace it without removing the fender
@paulcannon37710 ай бұрын
Noooooooo..... This is a 15 minute repair . All you need to do is take the one bolt out of the steering shaft and lay it to the side for easy access to the sensor
@pradeeshabram2 жыл бұрын
🥰🥰🥰
@triptonmiller85327 ай бұрын
Video has no sound. Worthless
@andrewwalls55682 жыл бұрын
Lmao did you really just say something high quality from Jeep??? lmfao
@isidoremartinez25292 жыл бұрын
I also have a 2014 Jeep Wrangler 3.6 can you tell me where the a/c fan relay is located at its not on the driver side by the lights Thanks
@kevinriffey99706 ай бұрын
@@isidoremartinez2529its next to brake booster on the side.