Pac RP4-CH11 wire harness instructions and troubleshooting

[@Austinwiththe07Aspen]

10:16 Bro I promise none of us are worried about the length of the video, we probably wish it was longer with more details and maybe a actual installation process 💯

[@vgsttvssvisionsvideopromo7249]

Foreal

[@homiefromfl]

Thank you soooo much for this video. Ordered one of these kits for an aftermarket headunit for my 07 Grand Cherokee without nav, but with the Boston Premium sound speakers and amp. This video has explained SOOOOO MUCH and I feel much more confident about doing the install myself. I appreciate you going into detail about this harness. It's as close to getting the job done by you directly. If I have any issues, I'll see if I can reach out with questions!

[@kellyhaydu8712]

This helped me more than you know. Thanks so much!!

[@msburrage74]

Dude thankyou so much for this! I thought my adapter went bad but just need to be relearned. That fixed my volume controls! I was about to spend a $100 for a new one to. You tha man!

[@ncastroclan]

Best video about this kit by far!

[@n3tfury]

Great overview of this harness. Got one coming in the mail in a couple of days. Thanks bud!

[@chandalarranch]

Thanks for your thorough video!

[@gaiusnormanyo]

This is such a timely video! Just got mine from Crutchfield to hook up to my Kenwood DMX47S in my 2013 Dodge Avenger. Had so many issues with an old Metra WM-CH13-SWC that stopped working as soon as I updated it via USB and no connection on an Axxess ASWC-1 after trying to salvage some of the Metra connection. Time to start from scratch, so to speak.

[@UserIsntHere67]

Haha I’m doing a 2011 dodge avenger

[@gaiusnormanyo]

@@UserIsntHere67 Everything worked fine for me watching this vid. Idk how to properly save the custom button controls, but I'm fine with the stock settings. Lmk how it goes for ya!

[@UserIsntHere67]

@@gaiusnormanyo That’s good to hear, my buttconnectors should be here in 3 days. Do you happen to remember what harness you used? If not I’ll just pop my deck out.

[@gaiusnormanyo]

@@UserIsntHere67 I used the non-amp harness that came with the PAC kit in this vid, bought from Crutchfield.

[@MatthewEngleby]

great video. liking your content. can you link video referenced about RP4 and factory amps? i have factory amp with 4 rear wires and no front wires. thx

[@MrInfamous1977]

No response? I have the same issue

[@ericsonic3977]

Very helpful, thank you!

[@chriswhelan1241]

Im using this for an Eonon android radio. What settings to get the swc. And how to hook it up? It doesn’t have a 3.5mm hookup, but it does have 2 swc wires

[@spins8085]

Great video…if i hook up the green reverse wire from the rp4 to the reverse trigger wire on my boss deck will it trigger the radio to switch to the cam when i put car in reverse. Or do instill need to hook up the reverse trigger on deck to a reverse light

[@jump0ffjoey129]

Just order one waiting for it to come in. Hopefully, I can get it done with this chinese Android radio to my 2012 vw jetta gli with fender audio. If I run into trouble, I'll ask you for some help. Thanks for the video knowledge

[@rubenlaroche7655]

I have a kenwood, what wire does the blue & yellow hook up to so that I can have steering wheel controls?

[@diamanteday8580]

Will this work with a boss radio? I noticed boss audio wasn't listed for the unit brands for the turn dial.

[@jeramiahbaronjr8908]

So if your using a boss audio system u would put that on 7 ?

[@MrInfamous1977]

Great info.. answered many questions. I work in a salvage yard and got a Kenwood with a pac and it came out of a gm pick up and I put it in my sons yukon amd I'm having all sorts of issues. I think it's because my sons vehicle has the amplifier. Only sound coming from the front. And I'm getting a buzzing sound. I pulled a wore schematic and im probably tied into the signal wores and not the actual speaker wire if that makes sense.. my sin is looking at me like wtf I need my tunes dad..😂 I'm trying. Any link to the other installation video regarding the factory Amp install?

[@cassandrabeacom4474]

Awesome video. I have a 2014 Jeep Patriot Limited with the extra speakers in the tailgate. I am going from uconnect rhb w/sirius to Amazon JOY-A019 w/dash camera front and rear. Please, advise😢

[@zeetaino62]

best one yet

[@wheelyking23]

now what number would i use on the interface if we use a cheap ebay one?

[@jesusiglesias622]

Hello I have a 2011 dodge Durango and I got a alpine halo9 and was wondering if this would work on my Durango since I got factory amp and steering wheel control

[@matthewbelanger535]

Great video. I got this working in a Jeep wrangler with a factory amp and factory sub but lost my sub. Any ideas?

[@jaecity02]

Thanks for the video. I had my aftermarket stereo installed to my 10 Dodge Charger without the PAC harness. Everything works fine (installed 8 years ago) but my OBD has been showing a U0184 code. Would this harness remove that code?

[@dawnconnelly7238]

Gx3800 install on 2017 jku…how do I get the phone control on steering wheel to stop using uconnect and go through radio?

[@dawalke21]

Should there be a red light on the pac interface device? While hooking my radio up, I spliced the remote wire into the ignition wire and when I pushed the radio back in, the radio seems to have lost power. I’m wondering if the red light on the pack harness is indicating a power surge or just that power is going it it. 2013 town and country. Also I should add that, it’s a kenwood ddx373bt and it’s a red blinking triangle light that keeps flashing. The radio powers on fine when I connected it to an external power source.

[@deejaydemon3145]

This is a common issue, called the company support number and they told me to toss it in the trash and buy another one. For a device that cost me $150, that's some bullshit. It's been a little over a year. Apparently many of the earlier models were defective.

[@jtcoker2684]

Hey man, what if your radio is not listed for the rotary switch. What number do you put it on?????

[@jamesak257]

I need some input on this have it in a 2013 jeep wrangler with a factory amp rear is not working and front are working opposite front left is front right front right is front left could you help me where it went wrong

[@Mike-n5l8n]

Trying to hook up a dual aftermarket. My 2013 Jetta had a JVC aftermarket that worked. I cut the wire that connected to the JVC and rewired the connector for the Dual. But no power. No LED to the RP4-VW11, any help?

[@kingme0072]

What is the program number for an atoto radio

[@teenice894]

Red wire doesn't put 12v when key is on.. just learned the hard way. Reverse camera wouldn't trigger on when connected to the red. Did some digging and canbus uses red for data to vehicle computer not 12v

[@reeboostmedia3900]

No clue where to hook up the blue with yellow for my Kenwood. 2015 wrangler with SWC, the blue box is recognizing the signal but nothing for blue w/yellow wire

[@pamelaherman7863]

What dial do i turn it to, i have a ankeway 7inch double din?

[@andygaskins225]

Im sure this has been asked but how do i know whether to use A or B? Do I just look at the wires and make sure they look simular?

[@htes05]

Only one of them will fit. I have a 2012 Ram and it is taking the plug with the beveled corners. Hope that helps!

[@michaelgonzalez6692]

Got cheap double din radio with rearview camera radio off Amazon. Trying to hook up rp4-ch11 interface, can't figure out radio setting for radio select switch. Also ,no steering wheel controls not sure where to hook up harness amplifier wiring . No power antenna just regular antenna. 3wires not hook Ed up purple/white -speed. Key wire- brown, Amplifier wiring blu-white . Both Blu are connected antenna wire.? Is plugging in interface enough if I don't have steering controls, and can't find setting for radio setting to put at on interface

[@michaelgonzalez6692]

The person looked at my car from a radio install place and said I have an amplifier so I purchased the interface

[@cotorro6713a]

Hello, how are you? I wanted to ask you a question. Have you installed a c2r gm29 interface? do you have any video? I installed one in my 08 yukon and when the radio turns on it makes a noise like static, do you have any idea what it could be? Thank you

[@mrgallardo777]

For the new alpine w670 they have 3 wires to connect to the steering wheel. Not the 3.5 plug

[@ronmelbanegas8179]

How I connect the camera to the stereo?

[@556omerta]

Yea same here man I’m having such a hard time with a install is there any way to get into contact with you ? Thank you in advance

[@mattlimmer1406]

Dude I need your help and install a new radio but there's no audio coming out bit there's power to everything and when I plug my old one up it works fine please help 2003 kia sorento

[@TopNoTchVSOP]

Where is the video to bypass that brake light sensor or tie into it?

[@druntyable]

My aftermarket radio is not on the list of radios for the interface module, any suggestions for the number on the dial I should choose for my radio?

[@spins8085]

7 is other

[@ramonwilliams6585]

Other doesn't work for me has it worked for anyone

[@syntaxis5584]

I have a 2008 Jeep grand Cherokee with a Boston premium audio factory amp, my RP4-CH11 does not turn on the amp

[@timspatola1334]

I’m lost. Where do I hook the blue and yellow wire up

[@nvidiashield495]

On an Alpine wire harness the yellow with the blue strip is supposed to go to your parking brake wire. It’s a safety feature to prevent certain functions unless you have the vehicle in park. Some people bypass this by grounding it for example if the radio is installed in a boat. Grounding this wire in a vehicle is never done by professionals because of liability and your safety . If your installing in a vehicle you will need to figure out where your parking brake wire is and use a special connector to tap into your brake wire Like a posi-tap connector

[@ramonwilliams6585]

Need help if i hook the blue/white amp wire from rp4-ch11 harness to aftermarket radio amp wire I still get no sound. Or could it be the amp is not working

[@trippingwiththedrews3850]

Having the exact same problem. 😢

[@ramonwilliams6585]

@trippingwiththedrews3850 said thing is if I slice into two wires from the factory harness I get sound to any other small speaker I hook up. I was trying to save myself from wiring a whole new setup

[@trippingwiththedrews3850]

@@ramonwilliams6585 I ended up hard wiring to the speaker output from the aftermarket head unit to factory amp output plug. I could get the Stinger CH11 to work. Then after that even the Amfm antenna doesn’t work. Most likely powered by the same system somehow.

[@ramonwilliams6585]

@trippingwiththedrews3850 so your wired your speaker directly to the factory amp output

[@gurus5945]

Where you located brother

[@rjjones1106]

How do I hook up sub rcas to the interface?

[@jonathanlaird454]

You'll have to get the wiring harness that goes into the deck itself...

[@nvidiashield495]

You never linked to the video you made on getting speaker outputs wired to allow Bluetooth to work

[@KingZoneOne]

So where's the troubleshooting part?? Mine is not working, and the LED just blinks constantly without changing. The stereo does not come on at all, and there is a parasitic draw from this.

[@de04609]

Mine says to hold the button for 7 seconds. It’s supposed to blink 4 times and then it’s reset.

[@kenlreid]

What if you just have an aftermarket android radio not listed. what do you set the radio select switch.

[@R0CK070]

I'm stumped on this one as well. Did you get resolved? I brought a BMV734 by Belva

[@kenlreid]

​@@R0CK070 I left it on zero. Worked fine in Chrysler Town and country 2014

[@R0CK070]

@kenlreid Appreciate it. I'll update you on my install once I get past wire phobia 🤪. I'm slightly stumped on SWC and Maintaining factory rear view cam. Until I dig into the install. 👍