PAM 8610 amplifier - Mini amp board (insane bass)

[@byAbhishek]

this is magnificent amplifier... unbelievable sound... honestly i checked 3 inch 4 ohms 20 watt speaker can't handle the power produced by this...

[@LetsGetStarted11]

Can we use 30×2 wat speaker in this circuit.

[@shankarnishad4375]

rply

[@tlrautomotive8410]

Plug in a 12v battery and rock it outdoors

[@juancarlosmelgarejo6120]

Output is wrong, it is L-L+ R+R-, just look at the movement of the speakers cone, it goes back and the forward, when a bass sound is played the cone must move forward first

[@crazyspeakerpro9584]

0:21 that voice crack though

[@riyaanpawar2005]

Because it is recorded on phone microphone 😂

[@riyaanpawar2005]

But truly it sounds good

[@los___santos]

i have many pam8610 its really crazy amplifier i hope i can find new version of pam amplifier maybe pam8650

[@21thTek]

welcome to the most scientific & technical test-review ever !!!

[@haajee1]

Combine it with a VHM-314 bluetooth 5.0 audio module and you have for a few bucks a aweome sound set! :) Please review also the VHM-314 or VHM-314-V2 but the bluetooth 5.0 variants. :)

[@haajee1]

Mine PAM8610 arrives today and it´s indeed really powefull! Think also because the big 2200uF capacitor. :) Works perfect with the VHM-314(-V2) :) very nice!

[@plazmax]

Im thinkin same 👍

[@transporder]

very goog amplifier pam8610 🔊🎶

[@vuilledeeresh4116]

The Amplifier goes below 20 hz and may damage your speakers while getting very hot.

[@macalsuperstarsksk2083]

Hello sir 12v supply but what is the harms of the charger

[@MohammadAsif-mq1ek]

Which amplifier sound good pam8610 or tpa3116d2 your opinion. You check also tpa3116d2 amp with bass and treble. Reply must I m from Pakistan

[@yakshpatel8312]

What was the waltage of your speakers? And can I run a 30w subwoofer with 10w speaker in it?

[@XenyQ_OFF]

Yes

[@tetearalte6226]

Sir how much ampere do you used? Can you please tell me also with voltage input

[@jeffm2787]

Too bad these things throw sooo much RF out it's insane. Edit: purchased a couple, they sound like crap. TPA3116D2 based amps are a better choice. PAM8610 has tons of noise as well.

[@yourajbadgujar7837]

how's bass compare to tpa 3110?

[@shrikantbhoyarphotography8645]

Wich voltage & Amp Adapter use for get best performance ?

[@alexisenciso3247]

Sir how much ampere on your 12v power supply?

[@als-techreview]

I am using 12V 3A. But it will work even on less amperage..

[@dragoncity6909]

@@als-techreview can i use usb instead of power supply?

[@Bljat47]

​@@dragoncity6909no. Its working good only on 12V and minimum 1A

[@balrajbalraj7547]

Lot better than TPA3116D2 which I recently bought 2.1 amplifier from Aliexpress.

[@jeffm2787]

Not sure what you bought, but no generally not. The TPA3116D2 normally blows this away. I own a few versions of both.

[@yahnsolo]

TexasInstruments TPA series are far better than this PAM from Diodes Inc. This PAM especifically is very noisy despite the good bass. Maybe its my boards (had 2 different models) but both have those cracky highs crisps at low volume (distorts like 4bit sound..)

[@euvo_sound]

@@yahnsolo the pam 8610 boards have tons of revisions over the years

[@s.ksondhiya9427]

Good very Nice bass and Volume

[@nandoashari27]

I have a really crazy 8610 pam power amplifier👍

[@Synthematix]

Its not true audio though, class d work from a modulated square wave, classic tda analog chips will sound much better.

[@jtstatus2225]

Can i connect 12 volt setup box adapter ?

[@Rocky69617]

How many watts your speakers ???

[@ECHOVISON]

Can i put a microphone?

[@atrelluzroig8529]

Solo para aportar; la POSICION CORRECTA de los polos es esta |-|L|+| |+|R|-| yo me habia guiado de otros videos y de paginas web que mostraban los contactos asi |-|L|+| |-|R|+| pero esa posición está mal hacia que el parlante derecho(R) sonara muy mal no habia casi nada de graves, asi que esta es la posicion correcta |-|L|+| |+|R|-|

[@extremeroom7u7]

Lo indica la placa

[@jonfrost885]

I cant find any 5w2* +10w amplifier subwoofer circuit board, any suggestions?!

[@ankitbaria726]

You can use any 2.1 home theater board Like tda 2030 ic and many more

[@MACFiFth]

don't buy those amplifiers i tried them already and its awful real tda2030 is discontinued by the real manufacturer

[@MACFiFth]

its better to salvage a working amplifier or car stereo or buy some Class D amplifiers instead of Counterfeit tda2030 if you are planning to make a subwoofer amp then buy Class AB it only costs $20 or $30 only if the seller is trusted and also tested

[@Sulukrindutv]

Speaker Piro inch iku mister?

[@bimmer8061]

it's loud amp?

[@subkarpaty]

better than TDA amp?

[@vighneshnyk1695]

Sir I want to make a speaker but I'm confused which one to take pam8610 or pam8403

[@nishantkushwaha5277]

8610 is best 8403 is outdated

[@umeshyo04]

How to identify +ve & -ve terminal at the output of the amplifier

[@manishsaurav7955]

Middle are negative and side are positive

[@atrelluzroig8529]

@@manishsaurav7955 incorrect

[@atrelluzroig8529]

Solo para aportar; la POSICION CORRECTA de los polos es esta |-|L|+| |+|R|-| yo me habia guiado de otros videos y de paginas web que mostraban los contactos asi |-|L|+| |-|R|+| pero esa posición está mal hacia que el parlante derecho(R) sonara muy mal no habia casi nada de graves, asi que esta es la posicion correcta |-|L|+| |+|R|-|

[@umeshyo04]

@@atrelluzroig8529 thnx for reply bro.

[@AntiKipKay]

Question, does it let you use a microphone as audio input?

[@mitubarman6614]

pre-apm would be required

[@AntiKipKay]

@@mitubarman6614 Thanks I got one and it works

[@sanjeevkumar-ox1tj]

sir, how to connected Bluetooth this board

[@adityakumarsingh5977]

What's the speakers wattage?

[@barserbas7264]

Whats your speakers model?

[@als-techreview]

This are Sony SS H551 speakers

[@barserbas7264]

@@als-techreview thanks

[@gamehacked25th]

Bro were did you find these soeker I want it

[@als-techreview]

Sony SS-H551 I find them from an old stereo..

[@JuanCoataPc]

Very noise ..

[@eraudio]

Music Very low qualit bass

[@andymarshman9546]

sounds awful to my ears (studio engineer)

[@Nexa_Bot77]

This is fake