Part 1 How to install Peel and Stick or 2 ply Self adhered modified roof. Base Sheet

[@LifeSurfingDude]

I'm glad this guy posted this video as it shows what you should never do! peel and stick underlayment is a very bad idea. once you get to a point when you need to replace a roof and you WILL get to this point, your cost would incredibly expensive. Contractors won't be able to take it off the roof deck. Sticky part is extremely aggressive. It will fuse to the wood and the cap sheet will fuse to the underlayment. And hence they won't be able to verify if nailing of decking was done properly and won't be able to remove everything properly. It will be extremely labor intensive. as you can see he already did a bad job at putting OSB down - all sheets meet in the same location. So, you would have no choice as to replace decking again. this guy doesn't think about the maintenance of the roof down the road. I see a lot of praising comments here but his video is just bad. do your own research. always put mechanically attached underlayment. avoid expenses down the road.

[@marmarc4203]

what is mechanically attached underlayment,????

[@HsingSun]

Thank you for your video. Question: What is the minimum inches (4" or 6") overlap?

[@OMGITSAAAJ]

Quick question. According to the GAF warranty it says that you'll get a 15-year warranty if installed on a primed plywood deck.. What does that mean simply a clean plywood deck is that considered primed?

[@watertiteman]

Primed with an asphalt primer. Problem with direct to deck install is, it will crack eventually along the seams of the decking. A small cheat is to apply a 4" strip of synthetic underlayment along the joints in the deck, that way the shearing effect is minimized.

[@russelleaves5435]

so this can be applied to shiplap tongue and groove type decking on an older house. the base will stick to that with no problem or should i nail felt first and then apply the base sheet.

[@pcm7315]

Not only do I give him thanks for the info; I give extra credit for keeping that hat clean.

[@jacobbutler6777]

You did very good other than the fact that you should’ve actually cut your very first piece of base at the 18 all the way across started with a half sheet so that way your labs don’t overlap with the cap sheet

[@etow8034]

Why didn't you use a SAM primer/adhesive on the OSB to make the barrier sheet stick better ?

[@thebrickandstoneguy]

Because I have not found it necessary and when I was trained by Polyglass they did not teach that.

[@realasscracka]

@@thebrickandstoneguy can U apply 30# Felt on top of that before Shingles

[@davidsosa7406]

Do they not sell the base sheet at Home Depot anymore

[@kennymartin379]

How does the roof look now it it leaking or not

[@thulsa5218]

How hard will it be to tear off the base sheet 15 years from now when cap sheet needs to be replaced?

[@Rick-yi6kk]

You’ll have to re-deck the entire roof. Search problems with peel and stick on the tube. Miami Dade code requires synthetic underlayment if using peel and stick so it can later be re-roofed.

[@mcw3560]

​@@Rick-yi6kkI don't understand. Do you mean that the felt goes under the peel and stick? If "yes," doesn't that defeat one of the main purposes of the peel and stick, namely that it adheres to the deck so that water cannot get underneath it? I understand the difficulty in getting it up.

[@user-ez2bs3fq1x]

Will this work on a flat patio roof? Do i need any ashesive?

[@thebrickandstoneguy]

It needs to be stuck directly to decking. It’s not an overlay product.

[@thebrickandstoneguy]

When going straight to decking use either asphalt primer or flashing cement (rubberized tar) at least on top of edge metals prior to installing the cap sheet (colored granulated top sheet).

[@12vLife]

Florida Approved? Is there any final roof product that can also be installed over it peel and stick too and not have any nails, screws or holes on the roof?

[@DUZWON]

base coat/ primer followed by Elastomeric coating

[@12vLife]

@@DUZWON over the peel and stick? got any links to that?

[@etow8034]

Not clear what you current roofing material is, but if you already have a peel and stick system you have to know if it has a non-stick or self-stick base sheet system. You cannot install any product over a granule top sheet. If it has a non-stick base sheet you can just remove the cap and base sheet from the substrate reusing your deck material, but if you have self-adhesive base sheet most contractor will simply remove the deck material and replace it with new plywood or OSB.

[@12vLife]

@@etow8034 Replacing the plywood or OSB right now sounds insanely expensive. I'm just wondering about future replacement if going directly over the deck.

[@etow8034]

@@12vLife That is true lumber prices are going through the roof now. This clip explains the difference between non-stick(Roof-Fast Base MA) and self-stick(Roof-Fast 95 Base) base sheets. kzbin.info/www/bejne/gafCqWqdnd5qh6M

[@walden6272]

What's the name of this product? The base sheet and cap sheet? Are they sold at Home Depot?

[@debbielwilliamson8546]

Thank you for all the info.

[@nickklaas4776]

Great video! Thanks for all the tips!

[@Brandon-no3vc]

Can you use this system in canada on a flat roof

[@etow8034]

I wouldn't use this type of roofing for your main house roofing, but they are great for garden and tool shacks with a low 2:12 slope. In Canada go with IKO Fast-Roof 95 Base self adhesive base sheet and Fast-Roof Cap sheet.

[@Brandon-no3vc]

@@etow8034 is that torch down?

[@etow8034]

@@Brandon-no3vc You mean the IKO Fast-Roof system ? No it a Self-Adhesive Membrane system (SAM). For a torch down system look at their IKO Torchflex system.

[@Brandon-no3vc]

@@etow8034you so your systems aren't as good as canadas?

[@etow8034]

@@Brandon-no3vc IKO is a Canadian company, if the roof system can withstand -40C to 40C it's good for all climates.

[@PIANOSTYLE100]

That's an amazing product. Very down to earth video.

[@adrianromerocodes3211]

what's the exact name of this product?

[@abumuna2299]

EXCELLENT EXPLANATION, THANKS

[@jasonsilfies9932]

Can u send a link to the rolls u use for the project. The base and top layers would b helpful please...Thanks

[@thebrickandstoneguy]

I’ll work on it. What part of the country are you located?

[@HmongUniverse]

@@thebrickandstoneguy I'm in Cal. Also would like to know where to get the base sheet and the top sheet. Thanks .

[@johnbuffalohomebuyer9986]

@@HmongUniverse home depot liberty brand

[@whitechris720]

Shouldn't you stagger the decking joints?

[@ydnABB11]

roof cowboy

[@jamesmoody9363]

JOHN 14:6😊❤🎉