Pentair SUPERFLO® VS (VST) Variable Speed Pump Operating and Programming

[@jmj002vp]

Every time the pool company gets a new cleaner they tell me my Superflow VS pump is broken and I have to show them your video. Thanks!

[@Doggo_Norse]

This video was extremely helpful!...I just got this pump installed and I didn't know how to program it..this saves alot of money! Thanks

[@loangrant6553]

Thank you for putting the pool pump setup instruction. I just wanted you to know that how much I appreciate it.

[@MrSkid56]

Thanks for the video- I was able to reprogram 2 pumps after someone installed them and set the filter to run 24hrs at 3450rpm and the Infloor pump for 16hrs at 3150rpm. I had to work fast as more than 6 mosquitoes were trying to get my legs!

[@SPL]

LOL - 😆

[@Hiker63]

Installed this pump along with the Flowvis. Surprisingly using your settings I'm getting 50 GPM at program 1 and 20 GPM at program 2 with the Skimmer and Kreepy on. With the Main Drain and Skimmer it's much more GPM and 95 GPM in the Quick Clean mode. The Flowvis really takes the guessing out of how long you should run your pump for a full cycle 👍

[@SPL]

Thanks for the update! The FlowVis is essential. Now you will really be saving on your energy bill. 🤑

[@Lifeafter50SF]

I just programmed my pump using your video..Thank you..

[@EweKnowWho]

Thank you so much! It’s surprising that the manual doesn’t explain the programming process very clearly, so your demonstration was super helpful.

[@katrinahayes7189]

I appreciate your videos I'm just starting a pool route next week it is new to me. I have been spraying Lawns for 15 years and now im moving to pools

[@SPL]

Good move. Pool Service is loads of fun ;).

[@loosenut1969]

Thank you very much! I do have a pool guy, but he does not come for several days and we are just recovering from hurricane Ian and the power wiped out the programming. It’s all set to go. Thanks to you.!

[@SPL]

Stay safe!

[@LongTermHoldr]

thank you for this, just bought this pump for the energy savings and your video made programming a snap.

[@JJ-oq7li]

I use this video every year when opening the pool. I leave it on Lee setting all fall and winter the program for late spring and summer fun.

[@HEAVENLYTUNESDJANGEL]

I was about to say the same thing. Please don't delete this video 😂. For the past 5 years this my to go to

[@vidstan]

So my 10 year old AO smith pump went out the other day and I needed a variable speed pump immediately because my pool was very green. I went to pool stores etc and no one could help me for about two weeks, so I went online, purchased the Pentair Superflo vs. The pump arrived two days later from Amazon (free shipping). I installed the new pump with new plumbing and electrical in two days. TOTAL COST of Pump/Plumbing & Electrical was $769. This was a $500 savings. I would not have done it without David's tips on installation. KUDOS TO DAVID!!!

[@SPL]

Your very welcome. Thanks for the great feedback! 👍

[@robbyantles5148]

😅t

[@laurayveronica]

Excellent video which help me to instruct my technician how to set up the RPM and time according to my pool size. He was going to set it up for longer hours that my size pool didn't need. Your video help a lot. Thanks.

[@2manytoyz123]

I installed one of these at my house earlier today. Your video made programming a snap, thank you!

[@SPL]

Thanks for the great feedback. It is a really good pump. 👍👍

[@katrinahayes7189]

I appreciate your videos I'm just starting a pool route next week it is new to me I burn been spraying Lawns for 15 years and now im moving to pools

[@RobertoMartinez-lr3su]

Thanks!

[@rmt400]

Thank you. This was very helpful and concise. Pentair should put a link to you video in the user guide :>)

[@Nick-ez5wf]

Hi David, thanks you have the best instructies video on youtube! Greetings from the Netherlands!

[@johnandvirginialabar8822]

How do you backwash the pool when the pump is shut down?

[@gcjctc2]

Thanks , your videos helped me install my new Pentair VS!

[@GUNTHER1]

Thankyou you saved me 3 times now from power outages I really appreciate your video cheers mate!!!👍👍💪

[@YOUandMeRealtyDotCom]

It Has To Be Reprogrammed After Power Outages? The Power Grid In Florida Is Shaky at Best and We Are In The US LIGHTNING ⚡️ Capital Here In Tampa Bay... Seems Like More To Go Wrong In This Florida Heat 🔥 The Motor Will Still Wear Out, Is It Easily Replaceable/Serviceable With That Mounting and Motor Controller Or... YOUandMeRealty.com

[@billmadden7280]

Thx for another informative video David. When I need to sharpen my knowledge I turn to your videos 👍

[@SPL]

Thanks Bill! 👍

[@stephaniepope3698]

I just had this installed a few weeks ago. While the start/stop does work on the timer, I recently needed it to run for 24 hours and pressing the start/stop and then 1/2 or 3 does nothing. It isn't on an automated timer that I know of. Any help would be appreciated. Thank you.

[@nang7411]

Thank you very much for the easy-to-follow instructions. I live in So California. Right now the pump is set at Speed 1(3000) for 2 hours, Speed 2 (1650) for 8 hours & zero for Speed 3. Should I make some adjustments in view of the hot weather?

[@SPL]

Yes, Increase speed one by 4 hours to run it 6 hrs at 2800 RPM

[@BetterDoYourHomeWork]

@@SPL You recommend running it for 14 hours a day in summer in California (100 degree temps)? Just had one installed yesterday.

[@LA-zc9rg]

So after using quick clean to vacuum will it default back to options 1 2 or 3 depending on schedule, automatically?

[@SPL]

yes

[@AZCardCollector1]

I noticed after I turn it back on that it says, "Prime" flashing, and it's a lower speed than what was set.

[@bobd3707]

Thanks. I needed something easy to follow. I appreciate it.

[@micheletruax5213]

I have a salt system pool and just had this pump installed on friday. The tech set it at Set1 2200 rpm for 6hours (12am-6AM), set 2 is 2700 RPM for 14 hours(6AM-8P) nd set 3 is set for 3000RPM (8PM-12PM). Is it me or does this seem like the system would be using more electric than doing me good? They did say that the Pentair should really be running for 24 hours a day rather than powering off for so many hours a day Please advise if i should manually adjust the RPM's.

[@micheletruax5213]

also wanted to add my pool is 10,000 gallons

[@SPL]

Would set it for 8-10 hours at 1800 RPM. Then 6 hours at 2200 RPM.

[@Loubrezzy0829]

Pump was set up running at 1 speed @3000 for 8hrs Florida Weather what would be your recommendation to maximize savings.

[@SPL]

1800 RPM for 14 hours. 2200-2400 RPM for 6 hours.

[@hobbswade]

Very helpful. Thanks for creating this content and your other great videos.

[@reactionsok]

Any concerns running the pump at night? Trying to be energy efficient We are on time of use so 8pm is optimal.

[@SPL]

No issues with running this pump at night.

[@tommypham5242]

I set the time and adjustments I wanted. It didn't start at 10am as I programmed by itself. Do I must hit start at 10am every morning for it to run on my settings ?

[@SPL]

No. If the pump is on and you hit start after programming it should run at that time. Check the AM/PM as I have set it wrong myself.

[@joemccart0722]

Thank you for video. Very informative, made it easy for me to configure.

[@Tunder007]

Great Video , Thank you , How can we rest the programing ?

[@SPL]

hold 1-2-3-Quickclean down for 3 seconds all at the same time to factory reset.

[@angelaflow6981]

I'm running the pump 32000 and the jets don't have enough pressure and there's some bubbles, what is the problem? Water turns green over walls. 🤔 Thank you 🙏 👏👏👏👏

[@SPL]

It could be the filter needs to be cleaned.

[@angelaflow6981]

Thank you for your quick answer. No, I'm cleaning the filter just shok the pool and water seems it no running o there's no sufficient flow.🙄🤔 what else can I do?🙏

[@Tunder007]

One more question , the main control board should be on Auto? service ? or timeout ?

[@SPL]

Auto

[@Tunder007]

when is on auto the pump light is on for only 30 sec but when i put in . service is always on how can you program in auto sorry for the headache

[@nerveagent2541]

Good video easy to follow steps and clear. Thank you for the help.

[@rubenscott3972]

Again it's been a long time but thank you for the videos

[@emilioreyeschavira6292]

This was every helpful thank you you saved me money and waste of time

[@gambosix6]

Perfect... solved my problem today..!!! However.. What does ALARM mean on the pump which I saw today and shut off the power to reboot. ???

[@SPL]

Just means pump lost prime. Usually air in the pump basket area causes this

[@bludika]

if you have a VS pump, can you no longer use a mechanical Intermatic pool timer?

[@SPL]

No, you can't after going VS.

[@bludika]

@@SPL then what timer can you use that's easy to use and doesn't break the bank?

[@ginacervi]

Your videos are super helpful. I bought a house with the Pentair system. I’m learning how to use it thanks to you. Question. I understand how to set the system but what changes should I make for the weather. How long should I run the filter and at what speed for 90 degree weather and what speed for 70 degree weather?

[@SPL]

I would cut the run time exactly in half from Winter and Summer to make things easy. Glad you found my videos helpful! 👍

[@HowToDoitright]

David i have a goldline hayward controller board inside the house for my single stage pool pump as a timer which allows me to turn the pump on and off as needed. i am thinking about changing my pump to this pentair superflo pump but i am confused how would i be able to integrate the control with my existing controller? any advise? ill appreciate it

[@SPL]

It would be best to go with a Hayward VS pump so that the communication is flawless. The Superflo VS was primarily designed as a stand alond pump without automation. Even connected to Pentair automation it is limited. The Hayward Super Pump VS 700 230/115V (Expert Line) Item # SP2670020VSP. This VS pump is comparable to the Pentair Superflo VS. It is only sold at retail pool outlets and not online. They come with a 3-year warranty. If your going for the Superflo because your pool equipment is 115V you can also get the straight 115V model: Super Pump VS 700 115V (Expert Line) Item # SP2670010VSP

[@danluban3050]

Great instruction and clear details. What does the "External Control Only" feature do? Does it ignore this schedule you programmed? Can the pump run the schedule and receive an override from an external controller?

[@SPL]

It is an option if you have an automated system connected to your pool equipment. The Automated system like a Pentair Easy Touch will override the pump panel and you would run it from the Easy Touch.

[@danluban3050]

Does anyone know what happens if a signal for speed 2 is being sent and another signal is sent for speed 3? Will the most recent signal win or will it give an error code? When signal for speed 3 drops, does it resume speed 2 from the signal which has stayed on?

[@michaelpigneguy6864]

@@SPL my "ext.control only" is lit up, how do i turn it off ? i cant operate the pump with it on, its seems

[@80kenuel]

My pump doesn't turn on automatically. I will have to hit the program 1 button so it can start. Do I have to have the power to the pump on 24/7? I have my control panel set up to give power to the pump at the time a programmed to start. Any help will be appreciated.

[@SPL]

Keep power to the pump 24/7. That is likely the issue.

[@80kenuel]

@@SPL Fixed the issue once I hit the start button. I had pushed the stop button once and left it like that thinking it will start the next day. The pump doesn't need power 24/7. Thanks

[@williamtharp561]

I sure would like to know the answer to a couple very basic question about this pump. Are you still available?

[@SPL]

Yes, they still sell this but in the new upgraded version.

[@ryangentile4592]

Can you recommend how to set it up with an aqua logic automated system?

[@SPL]

They won't communicate in that case - maybe the 2021-2022 version but the older ones won't

[@Aubreykincaid]

How do I keep it on continuous for freezing conditions?

[@SPL]

It does not have a Freeze protect mode so you will have to set a program run time that is 23:59 minutes per day.

[@collincollin8275]

is there anything I need to do to this pump if I drained my pool in preparation for getting a new liner later this season? I had leaks all over my stairs on my vinyl liner from my dogs claws so im going to replace the liner. I drained the pool in the meantime but there is still some water inside the sight glass of the pump and it's starting to turn greenish. Should I have drained that water out before storing for a couple months not in use?

[@SPL]

Would say a good dosing of chlorine once filled will cure everything.

[@Prime.sam.]

I have the same system that you are programming. Is there a way for the pump to stay off a certain amount of hours during the day? And how do I program the pump for a 30000 gallon pool. Like how should i run it.

[@SPL]

For that size pool the builder should have put a 3 hp Inteliflo VS on it. Would run this at 3100 RPM for 14 hours and then 2100 RPM for 7 hours.

[@darlenemelkonian3073]

question-after pool company installed Superflo VST on 6/13/22 we had reverse flow when we would clean the filter basket of the new pump. Tech added closing multiport (which we have never had to touch for 14 years unless backwashing) we set pump for 12 hours at 3k. Sunday 6/26/22 (13. days after installation of new pump) our system exploded. Pool co claims no responsibility. Others think foul play-we know because of security cameras-there was no foul play. All our valves were opened. Any thoughts on the reverse flow causing a build up in pressure enough to explode pipes? I hav tons of pictures and video-tomorrow the system will be taken apart and pipes will be replaced to try to uncover the mystery.

[@SPL]

Maybe the inlet and outlet were plumbed wrong. That is all I can think of.

[@ccaninus]

Just bought this pump. Thanks for the setup info.

[@SPL]

Nice. It is a great pump. 👍

[@jeffcrowder8013]

Thanks for this. Is there a maximum RPM that should be used during the longest part of the day? I have a small pool (4500gallon), but my heater needs a higher water pressure to run. Wondering what the max is without burning out the motor.

[@SPL]

Max is 3450 RPM and it won't damage the motor.

[@kdimitriu]

You show a graphic at 5:25 with a 14,000-gallon pool and a program that filtrates/circulates 14,400 gallons per day... I have seen videos claiming that pool owners should run the pump for double the size of the water since the water isn't just lining up by the skimmer to be filtered. True or False? Is, therefore, programming the pump for daily filtration equal to 1 times the size of the pool adequate?

[@SPL]

There are those who believe this. I will have to look into it more myself but this last year or so I have heard the same thing.

[@AScottH]

Is there built-in frost protection?

[@SPL]

No, there is no built-in Freeze Protection mode.

[@MHrfffdssswqqwuuu]

When I touch the superflo vs pump start and any button on that black pad I get electrocuted is this serious or can I continue to use plastic gloves when touching it?

[@SPL]

Probably not grounded correctly. There should be a copper bonding wire attached to the pump.

[@MHrfffdssswqqwuuu]

@@SPL when I turn off the breakers and the time clock I still get electrocuted. This pump doesn't have a heater what should I attach the bonding wire too?

[@Tube4Dev]

Hello, I stay in Northern Virginia. We have around a 26000-gallon inground pool. Length 42' and width 18'. My Pentair Intelliflo 3HP motor just went bad on the pool opening. No other Pentair pumps are available apart from this 1.5HP Superflo. We don't have a spa or any water feature, have a booster pump for Polaris. Will this 1.5HP work and if yes, what will be the ideal setting to run 12 hours to cycle all the water? Thanks

[@SPL]

It should work fine. 1800 RPM for 14 hours, 2600 RPM for 8 hours

[@Tube4Dev]

@@SPL Thanks a lot, appreciate it. Just ordered the Superflo pump, Let's hope they actually ship it.

[@saraw112]

Thank you!! What speeds and time durations should I run my 24 hour Pentair variable speed pump? (18000 gallon fiberglass pool)

[@SPL]

1800 RPM for 12 hours. 2400 RPM for 6-8 hours.

[@saraw112]

@@SPL thank you! Should I set the quick clean button too? If so, what speed and duration?

[@salmiddlet7614]

I live in north bay of San Francisco. I want to maximize the lower electricity rates during the overnight hours. Is it ok to have highest rpm’s running overnight, then lower rpm’s during the day? Just wondering if higher rpm’s need to be during hotter sunny part of the daytime? Thanks

[@SPL]

That should work on fine. At 1800 RPM during the day that will be enough to keep the water moving.

[@janarcher3516]

If i top the pump to clean out the pump strainer basket, then push start, the pump goes to number 1 . How do I get the pump back on schedule

[@SPL]

It will automatically go back to the schedule.

[@davidgarza77]

David how many gallons is that pool you just set up with those run speeds?

[@SPL]

About 17K Gallons

[@GUNTHER1]

Thankyou you saved me a lot of time and frustration!!!👍👍💪

[@haroldcallahan4887]

hugely helpful thank you

[@maryfrancesbautista7234]

Do you have a video for fixing error codes?

[@SPL]

Not currently. The manual has a good list of them all.

[@maryfrancesbautista7234]

@@SPL unfortunately I didn't have one, however Pentair emailed me one! Awesome that they do that

[@kgcane5195]

Thank you for this. Quick question though? If we want the pool to be heated with this pump doesn’t it have to run at 3000 RPM or above?

[@SPL]

It doesn't need to but it will take longer to heat on a lower RPM

[@sarahmangone7785]

Can you set the prime speed?

[@SPL]

Yes. There is a menu for that

[@julieguglielmi6230]

We just had an older Hayward replaced with this pump. Pump sits about 6 feet higher than pool water level (it's up in a retaining wall bed) -- it seems like the preset speed 2 isn't high enough and causes it to lose prime. Is there a magic number the speed needs to be programmed to or just trial and error? And is there a way to completely override the schedule and have it run on one speed until changed? I need the heat pump to run pretty continuously to get the pool temp up enough to swim in it...

[@SPL]

You have to tinker with the run speeds. There is no always on mode but you can program a 23:59 program by just setting the run time to start a 2:00 pm and turn off for 1 minute at 1:59 pm.

[@julieguglielmi6230]

@@SPL if the pump shuts off by itself at all I lose prime -- because the pump is higher than pool water level, the water drains back down and I have to refill the hair trap with water to get it primed again. It can't seem to self prime because of this. If I manually turn the motor off I close the suction from the skimmers/drain at the same time -- and only then can I just start the motor back up without adding water. I reprogrammed the speeds and times and just now realized it all went back to the factory presets.

[@apex36]

I have a 10, 000 gallon pool with a solar heater. What settings do you recommend?

[@SPL]

1800 RPM for 10 hours a day. 2800-3100 RPM for 4 hours to run the solar.

[@apex36]

Thanks. What times of the day to run the solar?

[@kja328]

newbie with inground pools. I have a pentair superflo vs running a 10000 gallon inground pool. It has a salt chlorinator and a solar panel heater located on the roof. I'm thinking 3000 for 2 hours, 1400 18 hours, then 4 hours at 2000. thoughts? Thanks in advance.

[@SPL]

That sounds fine. But when you want to use the solar to heat the pool you may need a higher RPM for a longer duration of time.

[@kja328]

@@SPL Awesome! thanks for the very speedy reply! loved the instructional video. I learned quite a bit.

[@jackboyne300]

Very very helpful! Thank you so much!

[@TimeFlyingBy1884]

What is the rpm for?

[@SPL]

That is just the revolutions per minute or pump speed.

[@GUNTHER1]

Thankyou very much saved me big time on your videos!!!👍👍💪

[@OLeonOfficial]

What would be the speed the pump needs to run order to use the heater? I have a RayPack new heater. I understand a certain speed is needed for the heater to work. I haven't used it yet (heater), just had the pump installed a few days ago. Thanks for any advice.

[@SPL]

I beleive the lowest RPM for that heater model is 1800 RPM. I prefer to run it at 2800 RMP or even the full 3450 RPM for a short time to heat up the pool or spa.

[@OLeonOfficial]

Thanks for your response. I asked the pool company, they say 28K RPM would be okay. It is raining today in DC, will give it a try by the weekend. But second question would be: what would be the benefit of a variable pump if the heater needs a specific RPM in order to run properly? Thanks again.

[@OLeonOfficial]

Thanks. From your reply I guess that the whole idea of a 'variable pump' looses its meaning, right? I.e. a specific speed is needed for the heater to run.

[@TonyRivera0206]

Excellent explaining

[@erickrhernandez1451]

Do you have any videos on how to program(s) Pentair motors for 24 hours? I have a pool that has algae and I already cleaned the filter. But I would like to programs the filter for 24 hours until the algae is gone.

[@SPL]

No but you need ot reset the schedule to turn on at 11:00 am and then off at 10:50 am 23:59

[@iamomeed]

I have this exact setup. But I put the flow vision after the filter. Also why do you need to have the high rpms for 3 hrs? Why can't you just leave it on low rpms all day?

[@SPL]

You can leave it on low all day but this pool has an automatic cleaner and it needs some run time on high speed to operate. Also, just on low speed all day you will notice that the pool gets pretty dirty unless it is screened in. The skimmer works best when running on a higher speed for a couple of hours a day.

[@iamomeed]

Oh ok. If the pool cleaner runs with a Booster pump would you still need high rpms?

[@SPL]

Yes, the booster pump needs the VS pump to be at around 1800 RPM to move the pressure cleaner effectively.

[@iamomeed]

Is there a specific reason why you choose 40 and 15 gpm? Sorry for the trouble

[@SPL]

Not really. I like a good flow during high speed so the surface gets skimmed. You can set the high speed lower if you like. I wouldn't set the low speed much lower.

[@chrissanza5251]

I purchased a home with 36x16 inground salt water pool. Deep end rougly 9ft & shollaw end roughly 4ft. I believe the pool has roughly 24,000-28,000 gallon of water The last pump was set to run 10h at 3000 rpm, 10h at 2200, and 2h at 1400. Not sure who set that program. I believe that is over kill. The motor was just replaced after 1 year since installed today because it became very loud (under warranty). I don't have a flow meter. Do you think the factory settings will work okay? Or could you recommend setting please?

[@SPL]

14 hours at 1800 RPM, 8 hours at 2600 RPM - try that.

[@chrissanza5251]

@@SPL thanks for the suggestion. I really appreciate it.

[@chrissanza5251]

Over time at the 1400 RPMs the pool pump isn't staying full in the glass top. I can basically see the low amount of water being pulled into the pump. Is this just because the rpms are so low? Is this okay? At 2600 rpms it's full.

[@drchamp1902]

How does this work with easy touch panel if I wanted to switch it to spa mode for example

[@SPL]

It doesn't work well with automation. Specifically designed as a stand alone type VS pump.

[@edgarfausto7667]

How do I know if it's A.M. or P.M. on the times

[@SPL]

That is on the program screen.

[@jacko3423]

Stupid questions from a new pool owner here (21,000 gal vinyl): -would programming the time matter if pump is attached to Intermatic timer since it will cut the power at certain time anyway? -when it first cranks up, it goes to prime, then speed 1 (let's say set for 2 hrs), then speed 2 (X how many hours)? -follow up to question 2, how long should I run the pump for each speed for a day? I heard it depends on the season/temp. TIA

[@SPL]

Take off the intermatic on/off trippers and leave that on. That will solve the first issue of it turning off the VS pump. For your size pool I would set it on low speed for 12 hours in the Summer- 1700 RPM and then a medium speed of 2300 RPM for about 4-5 hours each day. That sounds like a long time but the energy use is about 2 hours of a standard pump.

[@brianschin6122]

How do you know what speed to set at to turn the water. My pool is 29000 gallons? Do I have to worry about too high of a speed ruining the sand filter?

[@SPL]

Not really. Your sand filter should be rated for a 1.5 hp pump - especially if your pool is larger. Generally 2400 RPM will get the pool flowing very well and still save you on energy cost.

[@nouransaid3538]

Your Vedic is very helpful! The screen recently doesn’t show, that makes me unable to adjust it and program it! Any tips?

[@SPL]

Check the wire inside to see if it has come loose. Easy to do. Just unscrew the screen and you will see the wires under it.

[@nouransaid3538]

@@SPL thank you so much for your quick reply! I’ll try this and hope it works.

[@linger4605]

I only have program 1 on (cleared the other 2 program numbers.) It won't start. After I enter all the desired information 3000rpm, 5A.M. and 3 hour duration, it doesn't turn on at that time. What am I doing wrong?

[@SPL]

Could be the clock is not set right. The correct time.

[@linger4605]

​@@SPL Just checked and it is set correctly. After I'm done putting all the settings on program 1, so I have to do anything else?

[@linger4605]

I figured it out in case anyone else has the issue. This channel did not have an answer, but I do. Enter whatever you want in the 3 programs. You can't turn any of them off if you wish. Once you're done, start the "Quick Clean" program manually and let it finish. Once that is done, the system will automatically start the next day at your settings. "Quick Clean" forces the programs to start

[@mansonlambright8160]

Great video💪🏼

[@seanstrickland4970]

Thanks for the video!

[@ialien2077]

So... After in install and program it, I assume I turn on the intermatic timer and remove the Off trippers... right?

[@SPL]

Yes. Correct.

[@edwingonzalez6073]

Thanks David very helpful.

[@chrisgonzalez4354]

Thanks for your video! Do these settings work for an 18,000 gallon salt system pool in Northern California? I actually kept 2 hrs at 2200 rpm so I’m running 2 hrs @ 3000, 8 hrs @ 1400, and 2 hrs @ 2200 rpm.

[@SPL]

I would try 12 hours at 1800 RPM and then 8 hours at 2400 RPM. Easy and effective.

[@chrisgonzalez4354]

@@SPL thanks!

[@brianqueen7397]

We have this VS Pump and a Hayward salt chlorine generator for a 20,000 gallon pool any suggestions on run times and settings? Thank you for your videos!

[@SPL]

12 hours at 1800 RPM and 8 hours at 2400 RPM. That is equivalent to your standard speed pump running for 2 hours a day in electricity use.

[@stoneridgelandscaping2073]

Does 2500 rpms at 10 hours sound ok for a 1000 gallon pool? It does have a salt sell.

[@SPL]

Is that 1,000 or 10,000 gallons? I prefer 2 speeds. 1800 RPM for most of the time 75% and then a high speed of 2300-2400 RPM for 25% of the run time.

[@RockyStatue]

In general, is this your common schedule for most pools? 3 hour morning high run followed by 8 hour slow run? Thanks

[@SPL]

8-10 hours on a low speed like 1800 RPM and then 4-5 hours at 2400-2600 RPM. Depending on the pool size. But nothing on high speed at all really.

[@schreinermd]

Great video! Is it possible to program this pump with an app? The Pentair Home app doesn't list the VST as an available pump to add.

[@SPL]

I don't think it is compatible at this point.

[@PatriciaKRose]

Will this pump work with a pool and spa combo. I have a 10,000 gallon pool with spa attached. I have a 2hp pump now. Will it operate the spa with 6 jets? and how do you program it for spur of the moment heating up the spa and using with jets.

[@SPL]

Yes, it will work fine. If you don't have an automated system, you would simply push the Quick Clean Button, turn the valves to spa mode and start your heater. You would set the Quick Clean Button at 3450 RPM and for a run duration of 2 hours. Very easy.

[@tomm9493]

On this pump is there a way to change the pumps prime speed and amount of time? I don't see how? Thanks.

[@SPL]

Yes, the menu on the lid will instruct you. very easy.

[@Robots-and-androids]

how do I set or disable the prime speed?

[@SPL]

When you turn on the pump it will begin it's default priming at 3450 RPM for 5 minutes. To lower the priming speed, as the pump is in it's 5 minute priming mode simply hit the "-" on the control panel. Keep hitting it until the desired New Prime Speed is displayed. Next time the pump primes it should prime at that speed - say 2800 RPM

[@YOUandMeRealtyDotCom]

Lowering The Prime Speed Below 1700 RPM When The Prime Starts Will Disable It... #GotPrime? #AskMeHowIKnow

[@mitchputerbaugh1940]

Do you know what would cause my scheduled run time not to run after using quick clean? If run quick clean today my pump will not run it's scheduled time the next day but the following day (48 hours) later it resumes it's scheduled time.

[@SPL]

Strange. Not sure.

[@mawgs07]

Whats the recommendation for a SoCal 20k gallon pool?

[@SPL]

With an attached spa a 3hp VS pump. Without a spa or water features this 1.5 Superflo VS will work great.

[@mapools]

Thanks, just picked up a green clean with this pump👍

[@michaelpigneguy6864]

i read that to turn the "external control only" light off, i should hold the start/stop button until it turns off.....but ive done this and.....NADA, still lit up, pls help

[@banderajw]

The drive of Pentair 342001 do not retain the clock setting (time) in power faillure.

[@SPL]

I think for 24 hours.