Look next part here, click link: • How to assemble engine... Look previous part here, click link: • How to assemble engine... How to assemble engine VVT-i Toyota Part 28: Cylinder head
Пікірлер: 30
@GurpreetSingh-qu6tc4 жыл бұрын
Why 90 degree of turn after tightening the bolts by torque wrench,?? I m going to do head job for my 1.8 vvvti how much torque should I give to the bolts ?
@yiannku841Ай бұрын
These bolts are torque to yield. Degrees are more precise in the plastic region of the material, instead of torque spec
@MagicalLisp3 жыл бұрын
What is the tourqe spec for the head bolts?
@PeterFinnTheCarDoctor3 жыл бұрын
Yes, I will do new video: Tourqe spec for the head bolts
@alexmuzinga37614 жыл бұрын
How much if want to buy a spanel key to tie the cylinder board
@lupepantoja4225 Жыл бұрын
Can this torque be done on 07 rav4 2.4 ?
@PeterFinnTheCarDoctor Жыл бұрын
Yes
@williamtips49004 жыл бұрын
Peter finn how about the torque specs for a 2008 Toyota camry 2.4l 2az??
@PeterFinnTheCarDoctor4 жыл бұрын
Hello. Here the torque specs for a 2008 Toyota camry 2.4l 2az, two steps: 1) 1 st 79 Nm or 58 ft lbf 2) 2nd turn 90 degree
@francismarin89055 жыл бұрын
Do you have the repair Manual for SZ-Fe Engine?
@aymanalsanousi42393 жыл бұрын
how much for the cam shaft should i torque it ?
@bonganitshantshana8939 жыл бұрын
hi I put everything according and I started the car Bt now the is noise from cylinder head a tapping sound Bt its not hydraulic lifters
@PeterFinnTheCarDoctor9 жыл бұрын
Bongani Tshantshana Hello. Did you install the lifters to same positions. If we replace lifters position, then they could make noise.
@Imjustanotherguy8 жыл бұрын
It appears you are installing used head bolts. Those bolts are torque to yield bolts and should never be reused, they must be replaced.
@PeterFinnTheCarDoctor8 жыл бұрын
+Imjustanotherguy You are right, use always new.
@Imjustanotherguy8 жыл бұрын
Arek, you are incorrect. When torque-to-yield bolts are tightened they are stretched by over torquing them. They cannot be used again. Read the manufacture's instructions. You are wrong.
@tonykilbourn78125 жыл бұрын
Toyota bolts can be reused if within spec
@augustahill97125 жыл бұрын
Need torque settings
@kb98265 жыл бұрын
TK is 100% correct and you are incorrect Imjustanotherguy. I have the Toyota factory service manuals for a 2004 Toyota Matrix and it states you can reuse the cyl h. bolts if within the specs given in the manual. I do not have it in front of me at the moment but it's listed in step 47 or 48 I think. Your reply is 3 years old but I am replying in case it will help someone in the future. With that said, head bolts are not too pricey and it is a pretty time consuming job when doing this procedure on a Matrix,Vibe, Corolla 1.8 VVTi, so if a DIYer wants to be safe then new h. bolts are the way to go, but it is not required if the old h. bolts are within specs of Toyota's recommendations. Peter was just being nice in his reply to your comment in lieu of starting a battle what is right or wrong to replace or not. He mentions how one can check the h. bolts specs in this video in another part.
@sammaetaa77283 жыл бұрын
Thanks Peter
@PeterFinnTheCarDoctor2 жыл бұрын
Thank you 😀
@mdbadalmiah68085 жыл бұрын
Thank you sir 🇧🇩🤝
@elhectroncamacho25992 жыл бұрын
Thanks You, from Toluca México i see yours videos, i have a Toyota matrix whith motor 1zzfe, when i disessamble this, i see a hole what appear en this vídeo un min 4.23 in the SIDE of The chain this localitation up SIDE right, this conect whit The hole of The solenoide vvt, But appear accidental, My answer si why no is closed y appear maquinacion after fabricación
@PeterFinnTheCarDoctor2 жыл бұрын
You are welcome
@norikghoorchian51284 жыл бұрын
Don't need repair manual, very easy.
@imacarguy336 жыл бұрын
Whats the torque ft lbs. ?
@PeterFinnTheCarDoctor6 жыл бұрын
37 ft lbs.
@augustahill97125 жыл бұрын
torque settings head Toyota hyllux d4d 2006
@j.onofre66135 жыл бұрын
Peter Finn the Car Doctor it is the same torque for a Camry 2010 2.5?