Dear Sir, thank you for making the effort to produce this video. I am a Brit living in Sweden, and the local garage wanted an arm and a leg to fix this problem...
@aaanton115 жыл бұрын
Thank you for your kind words, I am so pleased you enjoyed the video, & managed to save a few quid 💷👍🏻👍🏻🚗🎄
@Charlie-be6fx4 жыл бұрын
How do I loosen the tensioner to just put a new belt on? It has to be slid I think but don't have a clue how
@aaanton114 жыл бұрын
Its in the video, pull the tensioner back, Thanks for the great comments👍🏻👍🏻🛠
@Charlie-be6fx4 жыл бұрын
@@aaanton11 Where abouts? Is it at the start where you lever it up? Mines not going anywhere sadly 👎
@nozi20005 жыл бұрын
Hi there great start to video till got to taking the wheel off. Please be safe next time never trust just the wheel jack Axle-stand! My friend die when working on his car with just the wheel jack. Didn't get the full story if he was mess about or it was just an accident. That with the safety side out of the way. I have the same problem with my car Peugeot 307 SW Petrol same looking engine very tight down one-side. I haven't seen anything on my Model but your video has help out many thanks for upload. Try and see i can make video too for upload but i'm an old man now.
@aaanton115 жыл бұрын
Thanks for the great information, hopefully you will figure it out 👍🏻👍🏻
@jameshamilton56476 ай бұрын
Is there two tensioners on this? My 2011 partner is stop start and cant for the life of me get the belt bk on 😢
@aaanton116 ай бұрын
Thanks for the great information👍🏻👍🏻🛠
@blairarcher89526 ай бұрын
What a shit design.Got one to do on my Bipper the same.
@aaanton116 ай бұрын
Thanks for the great comments👍🏻👍🏻🛠
@hobhead844520 күн бұрын
Very helpful video, thank you. Just to add, did this on my berlingo 1.9, didn't need to disturb the bottom engine mount or take the top mount off. There's just enough play if you loosen the three t50 bolts and lower carefully on a jack. Thanks again for a great upload.
@EdgewithHedge3 жыл бұрын
I have similar kind of arrangement in the belt and tensioner in My Fiat 1.9D engine. You are a great mechanic. Greetings from India
@aaanton113 жыл бұрын
Thank you very much! & Thanks for the great comments👍🏻👍🏻🛠
@grahamhanson39033 жыл бұрын
Thanks for this - just had to do my 2002 Berlingo with the same problem. Looked in the Haynes manual and it was useless. Mine has the Gates tensioner and there isn't a matching hole for the pin to take off the tension - there is just a ramp which isn't alot of use. I finally got a 15mm open ended spanner with a tube over it for more leverage and I put a piece of wood down the side of the spanner to stop it slipping out. I then clamped the extension tube under tension with a pair of mole grips. Once I'd removed the belt, I then removed the idlers to make it easier to get the tensioner out and back in again. I had the car on an axle stand and used 2 scissor jacks, one under the sump and the second under the lower engine mount so I could change the angle the engine went up and then down. Not a job I would like to do again but thanks again for the help given by your video.
@aaanton113 жыл бұрын
well done graham, Thanks for the great information👍🏻👍🏻🛠
@deniseclark26393 жыл бұрын
AXLE STAND UNDER SUMP ?????? NO NO NO AND LEFT ON JACK . PLACE STAND S UNDER CHASIS MEMBER
@aaanton113 жыл бұрын
😂 I think you need to watch again, I didn't put the axle stand under the sump, and my jack has a built in safety lock, which turns it into a axle stand, Thanks for the great comments👍🏻👍🏻🛠
@Aeronautico32 жыл бұрын
Señor muy bueno su video y su técnica los felicito por la rapidez y la facilidad cómo cambió su tensor, lástima que no pude traducir al idioma español gracias
@aaanton112 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@laszlomolnar90322 жыл бұрын
Szuper 😀😀 köszönöm szépen a videót. Sokat segitettél vele😀
@aaanton112 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@wayneharper33835 жыл бұрын
Just looking at having ago with my dispatch very similar set up so this should help many thanks for sharing
@aaanton115 жыл бұрын
Thanks for the great comments 👍🏻👍🏻
@AM-zn9gi4 жыл бұрын
If only all the mechanics are goo as you bro respect to you and your expertise
@aaanton114 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@AM-zn9gi4 жыл бұрын
@@aaanton11 Which is the correct amp alternator for Peugeot partner 2011 1.6hdi 150 amp or 180 amp not sure which one to get.
@daleharlow60063 жыл бұрын
Would this cause power problems?
@aaanton113 жыл бұрын
It would affect the alternator charging correctly but not power of the engine as in acceleration et cetera Thanks for the great comments👍🏻👍🏻🛠
@daleharlow60063 жыл бұрын
@@aaanton11 just wondered as it does run the fuel pump? I think. My expert making slipping noises and not running well over 2000 revs
@jessestrum2 жыл бұрын
thanks mate
@aaanton112 жыл бұрын
You're welcome! Thanks for the great comments👍🏻👍🏻🛠