Phanteks Eclipse P600S build - ft. 9700K & EVGA 2070 Super XC Ultra

[@scottyscotty7785]

I just got the same case, great video, this be handy for my building......

[@Subdubbin]

Thank you! Good luck with your build.

[@scottyscotty7785]

@@Subdubbin Finally done, what an awesome case to build in.....

[@LuisitoTX]

Debating if I should do push pull on mine

[@darkktint5974]

Nice you mount 6 fans on aio before mounting how are you able to mount them to the front when the holes are occupied when mounting to radiator

[@LuisitoTX]

How are the temps on it

[@TheMajorlucifer]

Hi , i have a question , can i put to top of case 2 140mm fans and 1 120mm fan ? Thanks.

[@jeremystout9145]

hey man there was a video of gamers nexus that the radiator tubes should be down and not up. did you have any problems yet with the watercooler like extreme noise or performence issues?

[@Subdubbin]

I watched that video. I sold this system a few months ago. I never had any issues with my radiator mounted there. The radiator tubes being down instead of up is a noise issue, not a pump issue by the way.

[@Subdubbin]

Thanks for the question though. It really isn't much of an issue to have the tubes on top instead of on the bottom. If you don't hear any noise, then you're fine.

[@bardavidson2102]

@@Subdubbin Why you sold it? and would you still recommend this case over the O11 Dynamic?

[@dragline.]

Is this a quiet build?

[@darkktint5974]

Ok I See you just mounted 6 in angles then the other 6 when mounting radiators with fans.

[@andresnunez2392]

How much did you invest in the total build I'm considering building one for my son

[@kevykevTPA]

Nice video, but only 2 screws per fan? I'll be using this to help with my build, my case should be here any minute.

[@Subdubbin]

I only had 12 of the long screws, so each fan could only get 2 screws for the AIO. I ended up using 4 screws per fan on the top exhaust fans. If you only use 2 screws per fan on the top fan bracket, then it will bend and not allow you to install it easily. Good luck with your build.

[@emeerhakeem532]

Thank you so much for the video dude... just got the case and dont know how to put the ssd in it

[@Subdubbin]

Check the user manual. Phanteks made a fantastic user manual for this case that should answer all your questions!

[@Subdubbin]

Or I can walk you through it if you can't figure it out.

[@jerry51311]

wow you have 6 fans on your aio. Are these fans controlled by cpu temp? If so, how to connect 6 fans to cpu fan pin on motherboard? I have this nice case, too.

[@Subdubbin]

This case came with a PWM fan splitter on the back ( see 10:57 ). I used this fan splitter to run the CPU AIO fans off the CPU FAN header on the motherboard!

[@jerry51311]

Subdubbin oh, so where did you connect other fans? with corsair hub?

[@Subdubbin]

@@jerry51311 I plugged the Corsair LL140 rear exhaust fan into the CHA_FAN1 header (Case Fan header 1) on the motherboard. I plugged the top 3 Corsair LL120 exhaust fans into a 3-way PWM fan splitter (came with the Deep Cool AIO) and plugged that into the CHA_FAN2 header (Case Fan header 2) on the motherboard.

[@jerry51311]

Subdubbin Thanks for your help! It's a nice tip for me as a beginner!

[@panosntinas2789]

Very nice build mate! I order the same case!! A quick question you have the aio front in push/pull config am i right? Im asking because i also have 360 rad in push/pull and i want to do the same!! There is enough clearance or tight and how much is temps in this case??

[@Subdubbin]

Yes, 360mm AIO is in push/pull. Yes, there is enough clearance to do this. I don't really remember the temps, but the CPU didn't go over 72°C under load.

[@panosntinas2789]

@@Subdubbin Thanks a lot... 😊😊

[@jacobfisch1935]

I'm going to order this case soon what brand parts do u recommend me getting

[@Subdubbin]

What are you using the computer for? What monitor do you have? How much are you trying to spend? I need some details to help you.

[@laz01gr62]

Your monitor is 27’?

[@Subdubbin]

Yes, Asus PG27UQ.

[@adro191]

6 intake and only one exhaust, that's too much positive pressure

[@Subdubbin]

I flipped the top fans to exhaust 9:03

[@stephenkennedy9687]

2:50 overkill much