Phrozen Wash And Cure Kit In-depth Test And Review

kindly support my channel / dennyswang
Phrozen Wash And Cure Kit In-depth Test And Review
Me personally like the cure unit because of the fan feature, it really safe time for drying and less hassle when post curing.
because wash and cure kit come as 2 separate unit, it may take more space, but it helps to keep production rolling when washing and curing.
25% discount using my code : Dewa0310
for DM Stash figure at dmstash.com
Build Plate Leveling Tester
cults3d.com/en...
Bottom Exposure Calibration
cults3d.com/en...
Exposure Tester
cults3d.com/en...
Thicker Validation Matrix
cults3d.com/en...
Print Angle Model
cults3d.com/en...
Amder Antialiasing Test
cults3d.com/en...
Stability Torture Test
cults3d.com/en...
Oval Tube / Tall Elipse
cults3d.com/en...
Compression Disk Test
cults3d.com/en...
Wire Mesh
cults3d.com/en...
Checkout Phrozen Website for Phrozen printer
phrozen3d.com/...
If you in Indonesia, you can buy Phrozen printer at tokopedia here :
tokopedia.link...
If you are in Indonesia, you can buy NFEP at tokopedia here
www.tokopedia....
Chapters :
0:00 - Intro
0:45 - Washing unit
4:21 - Test wash
6:38 - Wash advice
7:22 - Fun test
8:39 - Generate electricity LOL
8:57 - Curing unit
12:36 - A little issue
12:58 - Test Fan + Curing
15:12 - The result
#3dprinting #3dprinter #phrozen
If you interested to check my other work
Here my social media
FB : / nobodycustom
FB : / 3dmikron
IG : / dennys_wang

[@S.A.S.H.]

"So it has a spinning magnet, what if I..." Great idea. Awesome test.

[@2jedi5]

Glad to see you up and running again! Thank you for this review. Awesome print 😎 👍

[@fredy0908]

So this is basically a DIY kit, thanks for sharing :D

[@convolution223]

I enjoyed your humor and found this very helpful, thank you

[@bensgizmo2960]

You mentioned it's difficult to clean the plastic turntable for curing if you get resin on it. You can also sand it down and use an acrylic polish with a small buffing wheel. You have to be careful not to get it too hot from friction since that will create more issues. Much easier to use plastic wrap like you said.

[@wangdennys]

Yeah too much hassle. Plastic wrap is faster and cheaper.

[@S.A.S.H.]

That timer LED would light up my entire neighborhood, I think.

[@rdgd1rd]

Put a piece of black tape on sensor area so you can turn it on without lid .

[@wangdennys]

Indeed

[@allanlarsen3261]

I wonder why the cure timer can be set for hours, not just minutes? What would need to be cured for hours?

[@wangdennys]

IMO some hardcore resin.

[@quyreansoulsealer4002]

Thanks for the info. Does the wash station reverse direction in the middle of the wash? The Elegoo one does have the time clockwise, then the other half counter-clockwise. Im just wondering if the Phrozen does that also? Thanks.

[@wangdennys]

Nope

[@TymonScott]

Mine does

[@Magyarkhan]

my cure station dont rotate out of the box :(

[@OnceShy_TwiceBitten]

How well does it do the bottom or do you put it in a different orientation again later?

[@wangdennys]

Sorry i dont really get the question. But i usually just put it in. Leave it till finish. If the object hollow, after the cycle finish, i just rinse the inside several time manually.

[@plastiksurgeon9129]

If you soak the supports in hot water for a few minutes, they come off much easier. Just be careful not to distort the object when taking them off. 👌🏾

[@wangdennys]

i prefer to use nipper, the clacking sound each time i nip the suport, is like asmr to me LOL

[@plastiksurgeon9129]

@@wangdennys 😆😆😆😆

[@OnceShy_TwiceBitten]

removing them before curing but after washing is best too.

[@CookieManCookies]

Why no testing of ultrasonic cleaners like mean green? Hmm!

[@wangdennys]

Not available in my country. And ipa is dirt cheap here.

[@romancherfan9962]

Why is there such a price difference between the curing kits? I don't see a major difference

[@johnstiveavalosquispe5861]

Todo ese liquido es alcohol o agua? me parece demasiado, creo que no se puede reutilizar ese alcohol despues.

[@wangdennys]

alcohol it is dirt cheap here.

[@coulterjb22]

What have you found to be the best way to clean the wash container? Do you dump it into another container and cure/filter the particles after each use?

[@wangdennys]

Yes

[@tyomakes]

Hi Denny! Do you know where I can get this in Indo? I don't think stores in Tokopedia even have them?

[@wangdennys]

Sold out on tokopedia But you can request indocart in tokopedia to preorder it for you

[@tyomakes]

@@wangdennys Awesome, thank you!

[@sixandup939]

They made the cure station very short!

[@wangdennys]

Yep Very tight fit with full mighty 8k height build size.

[@ccarter1988]

Is there a reason you cured on the supports versus removing supports first?

[@wangdennys]

It is just a test print And would look nice if i place it like that on the shelf Hahahahahaha

[@lloydgregg637]

What % iso did you use in the washing station?

[@wangdennys]

99%

[@lloydgregg637]

@@wangdennys Thanks a bunch, I just got everything to start printing and your videos have really helped.

[@richardaubin1951]

Hi Denny, How would the drying compare to using a compressed air to blow off / evap wet alco?

[@wangdennys]

If you want faster job Definitely using compressed air is faster. But this is good if you hands are full with other work, put, set timer, and let them dry

[@richardaubin1951]

@@wangdennys Thank you for the response. I'm currently sourcing out products for my next venture. I will be printing X-One from BlueCast and their curing procedure involved drying off with compressed air according to their demos. Not sure if this method would work with their product and expected results.

[@kensaiix]

one word: ultrasoniccleaner

[@tek9058]

Pretty cool set, nice review but I would like a cover over my IPA tank. There is UV around, printers, lamps and also sun in sommer, indirect light will cure it also over time. I know from my supports which i didnt remove for 2 weeks, they got half cured by sitting in my basement not even close to my window. Good products but they skipped the thinking for the last 10% again. There are always small issues which create big trouble for the user, like the super small curing plate, firmware, switches on back, not flate plate on washing machine..could be used for general mixing and not only 3d prints. Also alot of stealing from Anycubic, metal parts, rotor, container...

[@yaqwsx0cz]

Look up a blog post named "Hand-on experiences with Mercury X Washing & Curing station and 15 USD must-have upgrades" (I can't post URL as KZbin will delete the comment). There are some tips on this.

[@Octopussy1999]

Never choose the Onlyfans option....