PID REX C100 quick initial setup

[@tysonabed5862]

Hi I already have c100 PID . How can I set tempreature 36.7 . I couldn't find way at the manual to do that . Its always give 36 or 37 never work with me to add dismal

[@glendooer6211]

If you move 8 inches to the left there is light so we can see what is going on.

[@Anarasha]

Thank you! I have this very model for a furnace, and I couldn't figure it out. Tomorrow I'll try doing this, and if it succeeds, I guess I owe you a beer :p

[@kyleio2305]

Hows the furnace?

[@Anarasha]

@@kyleio2305 p io worked perfectly.... for about half a cycle :p then my coil burned out because the one I got was made of too thin wire. I've gotten a new coil and am gonna install it as soon as I get a chance. But the PID controller and thermocouple worked perfectly! :D

[@jimboyechavez1987]

good day sir do you have diagram wiring omron e5cn-q2h03t-flk with solid state relay for my incubator

[@yehtet5673]

Can I have user manual for this controller in your video?

[@jimboyechavez1987]

good day sir do you have diagram wiring omron e5cn-q2h03t-flk with solid state relay for my incubator?

[@nyong97]

how about the REX-S100? ive been searching on the internet for it and it seems this model is already phased out, or maybe its just very rare, not a single youtube video on it, just a user manual in pdf format.

[@miki_car]

how to setup to heat to 36C than waits until drop to 30C and start heating again until 36C?

[@Samson.Boedefeld]

Same here

[@erlendh3257]

@@Samson.Boedefeld you need to tune the controller, thats what the P I D does, A proportional-integral-derivative controller there is a auto tune feature on the controller. use that

[@yoyokmra1]

Set ARU=001 its for activated auto tune, don't forget to set SV first...before set Auto tune

[@rahmatabdurrahim7789]

Hello. I wabt to ask something. How can you set the value into decimal point?

[@sackyrye40]

on page 7

[@tiagoimf]

Sacky Rye i cant put it in decimal

[@marvinloka1246]

Hello How successful is for incubator?

[@warunagayashan689]

I can't enter the initial settings even if I hold the set key together with the shitf key for 3 seconds.. What could be the problem?plz help

[@bennyroux5353]

How can I adjust a decimal point on the PID ? I see only figures before the decimal point.

[@josenungaray3939]

You need the Pt100 thermocouple, that one activate the PGdp function to see decimals, not posible with thermocouple K to N

[@alex-w8p2e]

@@josenungaray3939 how come the thermocouple used in the vide only has 2 leads, but a pt100 has 3?

[@josenungaray3939]

@@alex-w8p2e pt100 have 3 terminals I though that was the reason of the decimal presicion but now I see he uses a thermocouple R and have decimals

[@alex-w8p2e]

@@josenungaray3939 I know it is really confusing why some people have decimal points and others do not. I think it depends on the brand of the rex c100, that's why I want to buy a different model which I am sure has a decimal point.

[@alex-w8p2e]

@@josenungaray3939 I am back with an update. I bought a cheap rex c100 from bangood from EU warehouse and this is what I observed. I am running with a K type thermocouple. When I first plugged it in it did not have decimal point, but I reached the PGdp setting and set it to 1. I now have decimal points with a K thermocouple I cant't believe it. The model I bought doesn't have any brand on the front, it just says REX-C100.

[@yehtet5673]

Dear Sir, Let me know ReX model and sensor type.

[@JhanicSatori]

I am wondering...if we want to cool something? how do we set it?

[@RoboYYD]

Yes sure, if you use REX C series, you can enter the second class menu to set the forward or the reverse modes, two modes one for heating, one for cooling.

[@خالدالدليمي-ص2ق]

Hello Is it suitable for egg incubation

[@blessingtsimba6854]

Need answer too

[@rafawojtaszczyk1409]

what sensor model is used?

[@RoboYYD]

It depends on the temperature range you want to detect, different sensor different ranges. You can ask me to recommend.

[@gregklugiewicz5037]

Is the flickering light normal? Is it supposed to be solidly lit?

[@tanvirhossen5666]

how to reset rkc rexc100 model: rexc100fk02-M*AN please tell me reset all setting

[@bouteraimourad6745]

I have the same probleme, I can't reset it. Please tell me if you are do it.

[@RoboYYD]

I can help you with setting.

[@jinlim6575]

mine only has 3 numbers on the lock screen and will not let me move the numbers left to right. found out the best thing to do was just reset factory settings by making cod 911. some of these rex c100's are programmed differently..

[@PianoLessons_Teacher]

hi, how to reset factory reset?

[@jinlim6575]

@@PianoLessons_Teacher like I said. I changed the cod to 911 on mine to make it work. to access the menu and change things google Rex c100 PID owners - a must know! (how to turn off digital frequency)

[@PianoLessons_Teacher]

@@jinlim6575 This video shows how to access the code screen. When I write 911 to the code screen and save, will it be reset to the factory settings?

[@nguyenvu6371]

how to set up duty cycle for rex c100? because I use contactor instead of SSR.

[@nirobhasan237]

Good job

[@gandhisino3321]

excellent video

[@wangecieriksson7439]

Can you send me data's to program Rec c 100 for chicken hatchery. Thermocouple is K model 0-400Centigrade 2) How to amend overscale and underscale to Rec c 100.

[@carl_doesstuff]

Would have been so much nicer with out the music.

[@nolinicolas4237]

Gudday sir. How about i will use for cooling sir, all i need is 16-17 C means, 16C below it will turn-off and if 17C up it will turn-on. I will use as a switch(i will pluge my refrigerator) for restoring my pig semen. Thank u and God bles

[@jhonybeats210]

excellent tysm

[@cureforchronicdiseases1240]

Extremely ugly music has been given the end of clip😡.