Ford S-max 2007 2.0TDCi, Mondeo MK4, Galaxy, 103KW - EGR Valve cleaning

Changing or cleaning of EGR (AGR) Valve on my Ford S-Max 2007 TDCi 103KW.
PCM DTC P1335:77-6C
Kód: P1335 - Minimální doraz snímače polohy EGR
Based on tutorial from there:
www.forum.ford-club.cz/viewtop...
Music:
Sip Racer
Frame of Mine

[@salimmetin]

one of the best diesel engines ever made, is the on DW10 bases 2.0 TDCI of ford. Great engine, reliable. I have been driving with Galaxy 2.0 tdci for about 420.000 km's and it was still going strong.

[@nightstrangler]

Very Good video. Lots of help. Good man. THANK YOU

[@Placekmich]

I am glad that it helps 😊

[@BugRacer1955]

Great video 👍🏻

[@remifrommontpellier]

Thank you

[@1998jarno]

Thanks

[@johnpm1605]

I just blanked it off with a plate, no error codes and the hesitation at 1500 rpm has gone!

[@zlatankovacevic4281]

you blanked 2.0 TDCi or was it 1.8? 1.8 can be simply blanked without any software mods, I don't think that it's possible with 2.0

[@BOGDAN8270]

Спасибо за информацию топ 💯🔥🔥🔥🔥🔥🔥🔥 огонь

[@Dejwiszcze]

Angielski Very good video showing exactly what needs to be done when cleaning the EGR valve. Even if you showed a broken PIN, I really don't know what this part looks like, can it be changed?

[@Placekmich]

I am not sure if it could be changed - never tried.

[@AlexGnok]

What was the mileage (or km) on the car? Did you clean the air intake as well?

[@Placekmich]

The mileage was approx 213k km a I didn't clean the air intake. The main driver for this repair was lighting sign on the dashboard and not fluent moving of the car when it is cold. This repair solved the fluent moving of the car, but not lighting sign.

[@dalibor865]

Na tom egru je 6 šroubu dohromady ?

[@user-wt3zr8xu8e]

Я вывентил все четыре болта, но он не демонтировался. Но ещё одини болт нужно открутить. На видео его нет

[@Placekmich]

Yes you are right, one screw from the bottom. In my case case threw was already missing. In the description of the clip there is a link where is visible how to reach this screw.

[@mariusdorinciobotaru2829]

Hy, please tell me how tot adapt EGR values with forscan .Thank You.

[@Placekmich]

Hi there, after egr replacement i've just connected diagnostic to the car (i have wired version of diagnostic and I am using win10). Then i found in forscan egr adaptation and run. Thats all. Good luck.

[@Placekmich]

kzbin.info/www/bejne/nnupk6iendOIba8 in this video @00:31 it is visible... 8th line from the top is command egr values adaptation... I hope it helps.

[@liborschmid8916]

👍

[@siemensol83]

I have this model and I am wondering if it is better to buy new one or clean the old one. Do you know maybe part number

[@Placekmich]

You can try to clean the old one if it help. If not you can by new one. For my car the part number is 1436390

[@jasoncole7711]

What kind of spanner are you using at 2:30?

[@Placekmich]

Hi, it's 8mm... There are 2 screws visible at @2:06

[@jasoncole7711]

@@Placekmich thanks. "Hinged spanner" is the term I was looking for :)

[@Placekmich]

@@jasoncole7711 aaa... Yes hinged ratchet spanner... I though that you mean wrench size... 🙂

[@markdickenson1338]

Didn't help much because couldn't see ghe location of the 3rd screw holding the egr in , and wish hd would hold bloody think still for a moment!!

[@Placekmich]

Look at the link in the description, there is visible how it could be reached...

[@davidbernardino6636]

Hello, I have a problem and mounted on a Ford s Max, I have an analog scoreboard and I have mounted a digital scoreboard and when I connect everything, I get airbag failure

[@Placekmich]

The dashboard should not affect airbags at all. Maybe you can try to connect old dashboard and see if the airbag sign will turn of. If yes, you could have new dashboard from crashed car and airbag sign is stored in.

[@hahahawillie]

Hi, I have a 2012 2.0 TDci Mondeo 163bhp, would my engine be the same as this?

[@Placekmich]

Hi, your engine should be euro 5, mine is euro 4. There should be a lot of things same, but not completely. Unfortunately I don't have euro 5 available so I cannot tell you exact differences.

[@hahahawillie]

@@Placekmich Thank you, I will take a look later.

[@tomasvrtilek3591]

Ahoj. Všimnul sem si že vytekla i nějaká voda. Kolik jí asi tak vyteče?

[@Placekmich]

Ahoj, vyteče jen to co je vidět ve videu - pár kapek. V nádržce na vodu to ani nepoznáš. To koleno se ani nemusí vypojovat, ale je pak horší přístup k zadnímu šroubu.

[@ioandanielconstantin9814]

What is the value setting for EGR ?

[@Placekmich]

There is no value in forscan, just command "adapt EGR values"

[@hesperado]

How long did this procedure take?

[@Placekmich]

It depends on which car you're going to perform this procedure. On S-max it's little bit more difficult because you can't see on the screws. In my case it was approx 1,5 hour.

[@mirekmip]

Zdravîm, odkud jsi? Rád bych si vyčistil egr pod tvým dohledem. Dik

[@Placekmich]

Zdravím, opravou aut se neživým, tak že bych asi nebyl nejlepší dohled. Nicméně na čištění tohoto egru celkem není co zkazit. Jediný problém může dělat spodní šroub, který EGR drží - ten už jsem tam neměl od předchozího majitele.

[@dariuszb2834]

On jest niesprawny.zacina sie w polowie zakresu.widac dokladnie 7:55 min

[@dalibor865]

Kolík dohromady šroubku na tom euru ? 4 ? Díky za odpověď

[@Placekmich]

2 drží trubku co vede do sání, 2 co drží EGR na bloku motoru, 2 co drží chladič EGR a 1 že spodu egru (ten už jsem tam neměl, takže na videu není)

[@dalibor865]

Takže 7

[@sigi357]

Hallo muß man kühlwasser ablassen?

[@Placekmich]

Hi, no I did not drain the water. It run out only few drops as you can see on the video.

[@whiteapricot8212]

Привет, может была такая проблема, сейчас пробег 194к и я стал замечать, что при нагреве двигателя около 70 градусов, появляется небольшая вибрация, которая проходит при температуре 80.

[@Placekmich]

In my case the car at cca 1800-2000 Rpm started to twitch or convulsively speed up. The cleaning or replacing of the EGR valve solved the problem.

[@whiteapricot8212]

@@Placekmich Thanks 👍

[@marklong6701]

If u replace the egr valve on a Ford kuga 2.0tdci do u need to reprogram the valve or is it a straight swap over

[@Placekmich]

I never did this job on Kuga, but I think that you have adapt EGR values via diagnostic. Learn the head unit new positions of new valve.

[@vojtechstefan8045]

Odkud jste?

[@Placekmich]

Zdravím, severní Čechy. Ale opravou aut se neživým, jen opravuji na svých autech co je potřeba...

[@BOGDAN8270]

Сп

[@maximolotov]

Fucking looong and difficult

[@Placekmich]

If you are able to do it easier way, I am more than interested to see your work... ;-)

[@maximolotov]

@@Placekmich I am just saying that it is toо hard for me and I will never manage so I have to pay mechanic.

[@Placekmich]

​@@maximolotov Přeložit text It is no so difficult as it looks like... If you are able to use basic hand tools and you have diagnostic soft. than you are able to manage by yourself... Only tricky thing is bottom bolt on the EGR valve which was in my case already demounted...

[@serdarince9101]

I removed all the parts and couldn't find the third screw and agr then put all the parts back all my effort wasted😡

[@daudracip2680]

​@@Placekmich ja genaj schwierig und die ist mir abgebrochen was kan ich jetzt machen die Schraube ist abgebrochen die unterr

[@oilburner225]

I was none the wiser after the watching the video, music was an appaling distraction and the camera work was poor not to mention it was far to fast.

[@Placekmich]

Thank you for your feedback. Please send me example of your work, to I can learn some of your tricks during this kind of work. Thanks.

[@oilburner225]

@@PlacekmichI wouldn't know one end of the camera from the other. However there are dozens of well made instructional video's that present the subject in a well constructed and watchable manner with minimal or no need for music or other distractions. Take a page from their book and see what a well made video looks like, I wish you well.

[@IulianNegru333]

Stupid music...

[@Placekmich]

Nothing easier than turn volume down.... 👍

[@dandyer8351]

What a crap design