Plastic Oddities shares tips for correct installation of its fiberglass shower drain.
Пікірлер: 61
@foreverflowers77532 ай бұрын
thank you! I was told to use plumbers putty! glad I found you and your advice before I installed it! Blessings!
@basilbickford5906Ай бұрын
Thanks so much, my shower was leaking for the past year and I didn’t know how to fix it tell I seen your video….thanks again.
@ocramidajzj3 жыл бұрын
Sure enough the contractor who installed our shower drain (new home in 2012) used a ton of putty on the flange (where you used silicone) and the threads (which blocked the weep channels). No doubt, this contributed to the seal failing over time, as the shower floor flexed and loosened the putty, which was water logged. Replaced the paper and rubber seal and applied silicone per your instruction and no more leak. Thank you
@davehamel92982 жыл бұрын
Thanks for the comment.
@luizzyurr8 жыл бұрын
The best straight forward instructions on KZbin, thanks!
@cliff86756 жыл бұрын
Thanks you, especially for the explanation of the weep slots. That was the problem in my drain, plumbers putty was used.
@thomaswilson41068 жыл бұрын
Straight to the point it was perfect thank you!
@Rosk034 жыл бұрын
Yes Sir... Am doing this right now exactly as per your instructions. Thanks for the info!
@anthonycarr55148 жыл бұрын
Thank you. Saved me from searching the entire web. To the point.
@uptownphotographyАй бұрын
Great info. Could you tell me please what type silicone to use. I need to replace ours drain and want to do it correctly. The old one in leaking badly in basement. Thanks in advance. Phil
@andredicaire4026 Жыл бұрын
Thanks. I had to pull the pan and reinstall without bottom access. This the exact same drain and I now know to use silicone and not plumbers putty.
@blackbear922013 жыл бұрын
Very clear, specific, and helpful. Thanks for posting! :D
@victorian.mccormick62988 жыл бұрын
Blessings to you for a stressless, instructional film.
@davecpgh2 жыл бұрын
This is exactly what I was searching for. Thank you!
@donranski65573 жыл бұрын
Very good video BUT always love it when the instructions say 'do not over tighten'. How tight is too tight, for a 90 lb woman or a 250 lb man?
@joevacante27672 жыл бұрын
If it leaks its not tight enough
@jo-qp7mz Жыл бұрын
Man use left hand woman use right. That's usually how tight.
@shreddog358 жыл бұрын
Great video. To the point and all you need to know.
@jonshomo11678 жыл бұрын
+shreddog35 Perfect, straightforward. He also UNDERSTANDS the reason the drain is designed the way it is, with the side Weep Slots: and yep, seen plumbers I worked with gob those all up with putty. Block those and get a call back at some point with leak issues down below. Would LOVE to work with this guy!
@SaftTechnologies11 ай бұрын
Nice video, and nice choice of words sir.
@0u812icubi9 ай бұрын
Simple, quick, Done. Awesome
@wmborst8 жыл бұрын
Thanks, that was really helpful. I was looking for a special tool to tighten. Duh. Thanks again.
@TheMariCamil5 ай бұрын
What do you use to clean the acrylic surface before applying the silicone?
@catfish244 ай бұрын
Mineral Spirits which is also called paint thinner.
@luizzyurr8 жыл бұрын
Does the female portion get glued into the PVC pipe below?. Can you explain how that is done if you dont have access from underneath?
@stephenbell87573 жыл бұрын
You just replace the top part and the two gaskets under. Use long nose pliers to pull the old paper and rubber gasket out and slide the new one in between.
@catfish244 ай бұрын
@@stephenbell8757 B S you don't know what your talking about once everything is in place and glued up there is no replacing the rubber gasket unless you cut the pipe underneath and replace the whole drain.
@jruff07277 жыл бұрын
how do you connect to the drain to the 2 inch pipe on the floor ?
@peterdavila30455 жыл бұрын
I did an Oatey installation for a drain. The 2" drain pipe fits inside the female 2" piece at the bottom of this unit. You clean/cement the drain pipe and the inside of the female section of this plug. Then, you drop the pan on the drain pipe.
@carlosarellano135711 ай бұрын
Using logic, By applying silicone on top of flange, & then screwing into body drain, my logic says your disrupting the silicone from staying thick & consistent. Id do the screwing from below, if accessible
@pdanker18 жыл бұрын
EXCELLENT instructions
@Metalhead-4life5 жыл бұрын
That was a very thin bead of silicone. Installed mine earlier had to reuse the old female portion of drain, will leak test tomorrow hope all goes well
@candicearlebemus92787 жыл бұрын
Thanks guys, I'm ready to install a new one in my house.
@macflod Жыл бұрын
Can you use hydrid polymer sealant and adhesive instead of silicone?
@consciousbeing89823 жыл бұрын
Great video ,helped alot thanks
@FreshKicks45457 жыл бұрын
I wonder if we can use this as a reverse method to change the gasket?
@stanmanmedia Жыл бұрын
Great help
@TRINI123A4 жыл бұрын
Thanks. I worried about using putty.
@eddiebaby224 жыл бұрын
Thank you for your help
@Goku_gokum7 жыл бұрын
what about when the base already has the drain molded? That's what I'm installing & having a problem
@americanallthewayredneck39175 жыл бұрын
I ordered one from amazon and installed it..This had no weep holes.?
@dartme183 жыл бұрын
Looks like you'll be the only one weeping then.
@stephenbell87573 жыл бұрын
Either you bought the wrong one or you misunderstand that the "weep holes" are merely channels that are on each side that allow any water to run down into the DRAIN instead of leaking at the rim. If you look closely the channels are on the female part.
@sdranac3 жыл бұрын
Why don't we put another gasket on top isntead of silicone? Why don't they sell the kit with 2 gaskets? Is it possible to remove the top part once the silicone has set in if we have any problems later? thanks?
@Pw68723 жыл бұрын
The purpose of the paper ring is not to seal but to allow for tightening of the large pvc or brass ringnut against the underneath of the base. A pvc or brass ringnut will bind-up when it starts to tighten against a rubber ring, causing a bad seal. Hence the thin, slick paper ring. Up top, the new silicone will not bind when either pvc or brass is tightened against it. (This isn't rocket science.)
@catfish244 ай бұрын
Great informative video but the guy screwed the top portion with the silicone on it around and around when he should of held the top portion in place and tighten the bottom by doing what he did he smeared all the silicone out as he was turning the top portion.
@tomsmith66016 жыл бұрын
Thanks very helpful
@jashimuddin77163 жыл бұрын
Thank you
@CanetCalderon Жыл бұрын
Thanks this helps but i will use a gasket instead of silicone
@MrDan15096 ай бұрын
Then the drain flange is too high and the pan won't drain rt. You'll end up with soap scum all over!
@march7372004 жыл бұрын
Thanks sir.
@theman792005 жыл бұрын
What will happen if you installed the washers on top of the fiberglass vs underneath. I replaced mines because of a leak and it's still leaking. I followed the pattern of installing washers on top like it was when I took it off.
@talktome1004 жыл бұрын
Nothn
@Pw68724 жыл бұрын
First off, many top flanges are slightly sloped downward toward the opening, following the contour of the sloped base. Look at all your sink flanges-- sloped downward. If you compress a gasket under these sloped flanges, you won't get even pressure everywhere and there's a liklihood of leaking. Hence sillcone or plumber's putty used here. The bottom (underneath) flange is always perfectly flat and will accept even, snug pressure all around.
@dartme183 жыл бұрын
@@Pw6872 Excellent answer.
@TheIggypop13 жыл бұрын
Fiberglass bs it warps and it wobbly
@bguen12345 жыл бұрын
Silicone is not a good idea. When it leaks next time, good luck cleaning that silicone off the pan and getting a good seal again.
@bobshanery51525 жыл бұрын
The amount of silicone is not hard to remove. Take a rag and just rub. It will come off.
@KingdomeBleachers4 жыл бұрын
You must never have removed silicone before. It's not hard. Some pans require it over plumbers putty.
@dartme183 жыл бұрын
@@KingdomeBleachers That's right. Perhaps he's confusing acrylic with silicon.
@james-gu5kd3 жыл бұрын
I feel bad for the young fellow working with this guy he seems like a real hard ass. It could only be his son. Lighten up Pops.